Exsys EX-41021 Manuel utilisateur

Thank you for purchasing this Legacy SPP/EPP/ECP PCI Card. It is an

“ISA-like”PCI parallel port card that is specially designed to support

standard legacy parallel devices to any Desktop computer with PCI

slots. The precise hardware bridges 3BC, 378 and 278 ISA legacy port

address over PCI slots. It supports all enhanced parallel port features

that defined by IEEE 1284 specifications.

Features:

✓Supports 1P (or 2P) SPP/ECP/EPP Parallel Port(s) over PCI Slot

✓Supports PCI Bus Specifications 2.1 or above

✓Selectable Legacy I/O Port Address at 3BC, 378 or 278

✓Provides one DB25-Female External Connector

✓Dual Port Model: Provides one DB25F Flat cable

✓Works with major types of Parallel I/O peripherals

✓Supports Windows 98, ME, 2000, 2003, 2008, XP, Vista and Win 7

✓

Single Port Model:

Dual Port Model:

EX-41021

Legacy SPP/EPP/ECP PCI Card

Installation Guide

1. Introduction

2. Layout

J1: External

Parallel Port

Connector

JP1: Parallel Port Address Selector

Legacy SPP/EPP/ECP PCI Card

Since this card provides legacy parallel port(s) instead of

plug-and-play’s, its I/O port address won’t be assigned by the system

automatically. Instead, it needs to be set by jumpers. Please move

the jumpers (JP1 for Port 1 and JP2 for Port 2) to the designated

address shown by the silkscreen printing next to the jumper(s). Then

you need to do some installations manually to tell Windows where the

legacy parallel port address is, please refer to next section for more

detail of the detail software installation.

Note: Please verify your motherboard BIOS’s settings to prevent

from using the same I/O port address as this card, otherwise it will

cause a system resource conflicting problem.

JP1 (for P1)

JP2(for P2)

Description

I/O Port Address at 378

(Default)

I/O Port Address at 278

J1: Parallel

Port 1 (P1)

External

Connector

JP1: P1 Parallel Port

Address Selector

JP2: P2 Parallel Port

Address Selector

J2: Parallel Port 2

(P2) Connector

(Requires a DB25F

Flat Cable)

3. Selecting I/O Port Address

278

DIS

378

3BC

278

DIS

378

3BC

Legacy SPP/EPP/ECP PCI Card

I/O Port Address at 3BC

(Only SPP mode, no EPP/ECP at

this Address)

Parallel Port Disabled

After plugged the parallel card into your motherboard’s PCI slot, then

power up your system. Windows won’t detect any new PCI device

nor parallel port at this moment because the card indeed is a

“Legacy Parallel Card”like ISA card. You need to add it to Windows,

otherwise, it won’t function. For the dual port model, you need to do

it twice for both parallel ports.

The installation is cataloged to 2 portions, one is for Win7 and 2008.

The other is for Windows Vista, XP, 2003, 2000 and 98.

I. Windows 7 and 2008 Parallel Port Installation:

1. To go to Device Manager, right-click “Computer”icon, select

“Manage”

3. Installing Windows’Parallel Ports

278

DIS

378

3BC

278

DIS

378

3BC

Legacy SPP/EPP/ECP PCI Card

2. Click “Device Manager“, then choose “Action”, select “Add

legacy hardware”

3. With “Add Hardware Wizard”dialog box, click “Next”to continue

Legacy SPP/EPP/ECP PCI Card

4. Click “Install the hardware that I manually select from a list

(Advanced)”, then click “Next”

5. Select “Ports (COM & LPT)”, then click “Next”

Legacy SPP/EPP/ECP PCI Card

6. Choose “ECP Printer Port”device driver, then click “Next”

7. Click “Next”to proceed with ECP Port driver installation.

Legacy SPP/EPP/ECP PCI Card

8. Click “Finish”to complete the Add Hardware Wizard.

9. The new created ECP Printer Port (LPT3) was shown in the Device

Manager, but there is an exclamation mark (!) next to it. It is not

usable until we changed its resource setting to match up with the

hardware jumper settings mentioned in the previous section.

Legacy SPP/EPP/ECP PCI Card

To change its resource settings, right-click “ECP Printer Port (LPT3)”,

choose “Properties”.

10. In the ECP Printer (LPT3) Properties dialog box, click “Resource”

tab, then “Set Configuration Manually”.

Legacy SPP/EPP/ECP PCI Card

11. Click “I/O Range”, uncheck “Use automatic settings”, then click

“Change Setting…”.

12. Choose the I/O address range, please make sure it is the same as

your jumper settings, if the jumper was set at “3BC”(the factory

default was “378”, in this case, you need to choose “0378-037A”

instead), then the correct range selection is 03BC-03BE as shown

in the following screen shot. Please mind the conflict information

Legacy SPP/EPP/ECP PCI Card

window to see if there is any conflict. If the resource was in

conflict with other hardware, the ECP Printer won’t function

correctly.

13. Click “OK”to continue.

Autres manuels Exsys Carte PCI

Exsys

Exsys EX-44062 Manuel utilisateur

Exsys

Exsys EX-6074PoE Manuel utilisateur

Exsys

Exsys EX-3650 Manuel utilisateur

Exsys

Exsys EX-43063 Manuel utilisateur

Exsys

Exsys EX-6500E Manuel utilisateur

Exsys

Exsys EX-11087 Manuel utilisateur

Exsys

Exsys EX-44041-2 Manuel utilisateur

Exsys

Exsys EX-3512 Manuel utilisateur

Exsys

Exsys EX-44098-2 Manuel utilisateur

Exsys

Exsys EX-11042 Manuel utilisateur

Exsys

Exsys EX-44140-2 Manuel utilisateur

Exsys

Exsys EX-11072 Manuel utilisateur

Exsys

Exsys EX-44342 Manuel utilisateur

Exsys

Exsys EX-45362 Manuel utilisateur

Exsys

Exsys EX-41062 Manuel utilisateur

Exsys

Exsys EX-41054 Manuel utilisateur

Exsys

Exsys EX-44352IS-4K Manuel utilisateur

Exsys

Exsys EX-6072-4K Manuel utilisateur

Exsys

Exsys EX-1083 Manuel utilisateur

Exsys

Exsys EX-1093-2 Manuel utilisateur

Exsys

Exsys EX-44088 Manuel utilisateur

Exsys

Exsys EX-44384 Manuel utilisateur

Exsys

Exsys EX-41051 Manuel utilisateur

Exsys

Exsys EX-42372 Manuel utilisateur

Manuels Carte PCI populaires d'autres marques

ERMA

ERMA SSI 1417 Manuel utilisateur

SIIG

SIIG CyberSerial Dual PCI Instructions de montage

Moxa Technologies

Moxa Technologies CP-102E Manuel utilisateur

I-Bus

I-Bus IBC2602 Manuel utilisateur

Chelsio Communications

Chelsio Communications T5 Series Manuel utilisateur

Conrad Electronic

Conrad Electronic 97 46 71 Manuel utilisateur

Micro Innovations

Micro Innovations USB650A Manuel utilisateur

KTI Networks

KTI Networks KF-310 Manuel utilisateur

Asus

Asus SpaceLink WL230 Manuel utilisateur

SIIG

SIIG SC2475 Manuel utilisateur

TRENDnet

TRENDnet TEW-703PI Manuel utilisateur

Belkin

Belkin F5D7000F Manuel utilisateur

Pericom

Pericom PI7C7100 Manuel utilisateur

ADLINK Technology

ADLINK Technology cPCI-3548 Manuel utilisateur

Digium

Digium TE200 Series Manuel utilisateur

Allo.com

Allo.com 2nd Gen E1/T1/J1 Manuel utilisateur

Western Digital

Western Digital FireWire PCI Adapter Manuel utilisateur

Pyle

Pyle Gamelink PLINK1 Manuel utilisateur