Exsys EX-1309-9 Manuel utilisateur

Congratulation on your purchasing this high performance 4-port

RS232/422/485 3-in-1 to USB2.0 Adapter Cable. It supports 1 serial port which

can be set in RS232, RS422, RS485-2W, or RS485-4W modes. The UART based

serial port is fully compatible with most of the RS232C, RS422 and RS485

devices available from the market. It is an ideal solution for most of serial

applications.

Features:

USB 2.0 Full Speed (12Mbps) Compatible

Supports 1x DB9-Male-Connector RS232/422/485 3-in-1 Serial Port

Supports 4-wire RS422, RS485 and 2-wire RS485 Modes

Supports RS485 Auto Transceiver Turn Around by Unique Featured ATTATM

Hardware

Supports Baud Rate up to 921.6Kpbs

Supports Win2000, XP, 2003, 2008, Vista, Win 7, 8.x, 10, Linux and others

EX-1309-9

RS232/422/485 3-ini-1 to USB2.0 Adapter Cable,

w/ DB9M Connector

1. Introduction

2. Connector Layout

USB Type-A

Plug

DB9M Connector

(R232/422/485)

Mode

Selection

Switch

RS232/422/485 3-in-1 to USB2.0 Adapter Cable, w/ DB9M Connector

There is an eight 8-pin DIP switch next to the connector for changing the

operating modes, enable/disable terminator and the bias for transmitter and

receiver signals.

1. Mode Settings:

The DIP switch has 8 pins, the first 3 pins (M0, M1, M2) are for mode settings

(RS232, RS485-2wire, RS485-4wire or RS422 modes), pin 4 (TERM) is to enable or

disable terminator. Pin 5 and 6 (T+, T-) is for biasing TX+ and TX- signals. Pin 7

and 8 (R+, R-) is to enable or disable bias for RX+ and RX- signals.

Note: Pin 4 to 8 are designed for RS422 and RS485 only and should be

set to OFF when you are setting the port to RS232 mode.

Modes

Settings

(ON)

RS232

3. Mode Switch Settings

RS232/422/485 3-in-1 to USB2.0 Adapter Cable, w/ DB9M Connector

RS485-2W

(Default)

RS485-4W

RS422

2. Termination Resistor Settings:

The pin 4 of the DIP switch is to enable the 120 Ohm termination resistor

between RX+ and RX- signals.

DIP Switch Pin 4

RS485-2wire mode:

RS485-4wire or RS422 mode:

RS232/422/485 3-in-1 to USB2.0 Adapter Cable, w/ DB9M Connector

Terminator disabled (OFF, default) Terminator enabled (ON)

3. Bias Resistors Enable/Disable:

Pin 5 to 8 of the DIP switch are to enable (ON) or disable (OFF) the 4 bias

resistors for TX+, TX-, RX+, RX- signals respectively. Please note that you have to

set them to OFF if you are setting the port in RS232 mode.

Disable (default) all 4 Bias resistors for TX+, TX-, RX+ and RX-:

DIP Switch Pin 5

DIP Switch Pin 6

DIP Switch Pin 7

DIP Switch Pin 8

RS232/422/485 3-in-1 to USB2.0 Adapter Cable, w/ DB9M Connector

Enable all 4 Bias resistors for TX+, TX-, RX+ and RX-:

This Adapter Cable can be hot-plugged to the USB port of your computer

due to the specifications of USB. It supports the following operating systems.

The drivers were shipped in the following folders on the supplied driver CD.

1. Driver Locations on the CD

These instructions are for installing the drivers from the CD supplied with the

product. If you are installing drivers for Windows, when prompted for the

location of the drivers, specify your DVD drive and the locations according to

the following folder list:

4. Software Installation

RS232/422/485 3-in-1 to USB2.0 Adapter Cable, w/ DB9M Connector

2. Installing Drivers for (32-bit and 64-bit) Win7, 8.x, 10, XP, Vista,

2008, 2003 and 2000:

Insert the Driver CD supplied with the Adapter Cable.

Run (or double click) the Installer Program (e.g.CDM20824.exe ) in

the following folder of the driver CD:

\USB_to_IO\FTDI\(32_64bit)Win7_8_XP_Vista_2008_2008R2_2003

_2000

Follow the instructions of the installer program to complete the setup

procedures.

Plugging the Adapter Cable will hook the drivers into the Windows

kernel automatically.

The pin assignment of the DB9 male connector of the Adapter Cable is

dependent on its operation modes. Please refer to the following figure for the

corresponding mode:

1. RS232 Pin Assignment:

RS232 DB9(Male) to DB9(Male) Wiring:

5. Connector Pin Assignments

DB9 Male(Adapter Cable) DB9 Male(Serial Device)

1 DCD 1 DCD

2 RXD 2 RXD

3 TXD 3 TXD

4 DTR 4 DTR

5 GND 5 GND

6 DSR 6 DSR

7 RTS 7 RTS

8 CTS 8 CTS

RS232/422/485 3-in-1 to USB2.0 Adapter Cable, w/ DB9M Connector

2. RS422 and RS485-4wire Pin Assignment:

RS422 Cable Wiring:

3. RS485-2wire Pin Assignment:

RS485-2wire Cable Wiring:

DB9 Male (Adapter Cable)

1 TXD-

2 TXD+

3 RXD+

4 RXD-

5 GND

(RS422 Device)

1 TXD-

2 TXD+

3 RXD+

4 RXD-

5 GND

DB9 Male (Adapter Cable)

1 DATA-

2 DATA+

5 GND

(RS485 Device)

1 DATA-

2 DATA+

5 GND

RS232/422/485 3-in-1 to USB2.0 Adapter Cable, w/ DB9M Connector

Type

Specifications

Device Connector

Cable

Host Connector

Number of Ports

RS-232 Signals

RS422 Signals

RS485-4wire Signals

RS485-2wire

Baud Rate

Data Bits

Stop Bits

I/O address/IRQ

Parity

Flow Control

Power Requirement

Operating Temperature

Operating Humidity

Storage Temperature

DB9 male

USB

USB Type-A

TXD, RXD, RTS, CTS, DTR, DSR, DCD, GND

TXD+, TXD-, RXD+, RXD-, GND

DATA+(B)/DATA-(A)

110 bps to 921.6Kbps

5,6,7,8

1, 1.5, 2

Plug-and-Play (various)

None, Even, Odd

RTS/CTS, XON/XOFF

5V/110mA (USB Bus Powered)

0°C to 55C(32 to 132F)

5 to 95% RH

-20°C to 85C (-4 to 185F)

5. Specifications

Autres manuels pour EX-1309-9

Table des matières

Autres manuels Exsys Adaptateur

Exsys

Exsys EX-47925 Manuel utilisateur

Exsys

Exsys EX-45362IS Manuel utilisateur

Exsys

Exsys EX-6114 Manuel utilisateur

Exsys

Exsys EX-6011 Manuel utilisateur

Exsys

Exsys EX-1234HMVS Manuel utilisateur

Exsys

Exsys EX-1331-4KVIS Manuel utilisateur

Exsys

Exsys EX-47999 Manuel utilisateur

Exsys

Exsys EX-62020POE-SFP Manuel utilisateur

Exsys

Exsys EX-47000 Manuel utilisateur

Exsys

Exsys EX-1225 Manuel utilisateur

Exsys

Exsys EX-6001 Manuel utilisateur

Exsys

Exsys EX-1320 Manuel utilisateur

Exsys

Exsys EX-2346 Manuel utilisateur

Exsys

Exsys EX-1329 Manuel utilisateur

Exsys

Exsys EX-1322 Manuel utilisateur

Exsys

Exsys EX-6111 Manuel utilisateur

Exsys

Exsys EX-3505 Manuel utilisateur

Exsys

Exsys EX-1452IS Manuel utilisateur

Exsys

Exsys EX-6112 Manuel utilisateur

Exsys

Exsys EX-2346IS Manuel utilisateur

Exsys

Exsys EX-1177HMVS-WT Manuel utilisateur

Exsys

Exsys EX-47960 Manuel utilisateur

Exsys

Exsys EX-1331 Manuel utilisateur

Exsys

Exsys EX-1346 Manuel utilisateur

Manuels Adaptateur populaires d'autres marques

PCB Piezotronics

PCB Piezotronics 090B274 Manuel utilisateur

Auvidea

Auvidea J20 Manuel du produit

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuel utilisateur

Akribis

Akribis ITF-21-BISS-MIT Manuel utilisateur

Tenda

Tenda W54U Manuel utilisateur

ROHO

ROHO AGILITY Manuel utilisateur

PROLiNK

PROLiNK WN2001 Manuel utilisateur

Hawking

Hawking HUF2 Manuel utilisateur

Airlink101

Airlink101 AWLC4030 Manuel utilisateur

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuel utilisateur

Philips

Philips SWA4554S/10 Manuel utilisateur

JVC

JVC TS-C9D2B Manuel d'instructions

NETGEAR

NETGEAR A6100 Manuel utilisateur

D-Link

D-Link DWA-121 Manuel utilisateur

Philips

Philips SWA2037 Manuel utilisateur

Basalte

Basalte 0610-20 Manuel utilisateur

Yealink

Yealink EHS40 Manuel utilisateur

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuel utilisateur