Evoqua IONPURE IP-POWERDSP-G2 Manuel
10 Technology Drive
Lowell, Massachusetts 01851
Tel: (866) 876-3340 Fax: 978-934-9499
www.ionpure.com
IONPURE
®
G2 DISPLAY
BOARD
For use with G2
Power Controllers
Operation
&
Maintenance
Manual
IP-POWERDSP-G2MAN
November 2011
Revision 1
Manual Covers Part #:
IP-POWERDSP-G2
IONPURE ®
G2 DISPLAY BOARD – IP-POWERDSP-G2
IP-POWERDSP-G2MAN Rev 1 Page 2 of 25
Table of Contents
DISCLAIMER STATEMENT .................................................................................................................. 4
PROPRIETARY RIGHTS STATEMENT ................................................................................................ 4
MANUAL REVISION HISTORY............................................................................................................. 4
1INTRODUCTION ............................................................................................................................. 5
1.1 Caution and Warning Messages ................................................................................................ 5
1.2 General Description ................................................................................................................... 5
2INSTALLATION............................................................................................................................... 7
2.1 Requirements............................................................................................................................. 7
2.2 Panel Mount............................................................................................................................... 8
2.3 Connections ............................................................................................................................... 8
2.3.1 Connections to a Single G2 Power Controller....................................................................... 8
2.3.2 Connections to Multiple G2 Power Controllers ..................................................................... 9
2.4 Power Controller Setup ............................................................................................................ 10
2.4.1 DC Output Current Range Selection .................................................................................. 10
2.4.2 Unit ID Selection................................................................................................................. 11
3OPERATION.................................................................................................................................. 12
3.1 Control/Navigation Keys........................................................................................................... 12
3.2 Menu Structure......................................................................................................................... 13
4GETTING STARTED ..................................................................................................................... 23
4.1 Initial Startup ............................................................................................................................ 23
4.2 Output Current Adjustment ...................................................................................................... 23
5TROUBLESHOOTING................................................................................................................... 24
APPENDIX – UL AND CE COMPLIANCE........................................................................................... 25
List of Figures
Figure 1: G2 Display Board.................................................................................................................... 5
Figure 2: G2 Display Dimensions........................................................................................................... 7
Figure 3: Panel Cutout Dimensions ....................................................................................................... 8
Figure 4: Connections to a Single G2 Power Controller......................................................................... 9
Figure 5: Connections to Multiple G2 Power Controllers...................................................................... 10
IONPURE ®
G2 DISPLAY BOARD – IP-POWERDSP-G2
IP-POWERDSP-G2MAN Rev 1 Page 3 of 25
Figure 6: Current Range Selection DIP Switch .................................................................................... 10
Figure 7: Control/Navigation Keys ....................................................................................................... 12
Figure 8: Menu Tree Structure............................................................................................................. 13
Figure 9: OVERVIEW Screen Example ............................................................................................... 14
Figure 10: RUN Screen – Page 1 ........................................................................................................ 14
Figure 11: RUN Screen – Page 2 ........................................................................................................ 15
Figure 12: RUN Screen – Page 3 ........................................................................................................ 15
Figure 13: RUN Screen – Page 4 ........................................................................................................ 16
Figure 14: RUN Screen – Page 5 ........................................................................................................ 16
Figure 15: SETUP Screen – Page 1 .................................................................................................... 17
Figure 16: SETUP Screen – Page 2 .................................................................................................... 18
Figure 17: ALARMS Screen – Page 1 ................................................................................................. 18
Figure 18: ALARMS Screen – Page 2 ................................................................................................. 19
Figure 19: LOGS Screen ..................................................................................................................... 20
Figure 20: MAX VALUES Screen......................................................................................................... 20
Figure 21: MIN VALUES Screen.......................................................................................................... 21
Figure 22: MODULE OHMS&S Screen ........................................................................................ 22
Figure 23: DIAGNOSTICS Screen....................................................................................................... 22
List of Tables
Table 1: Unit ID Selection .................................................................................................................... 11
Table 2: Troubleshooting ..................................................................................................................... 24
IONPURE ®
G2 DISPLAY BOARD – IP-POWERDSP-G2
IP-POWERDSP-G2MAN Rev 1 Page 4 of 25
Disclaimer Statement
The operation and maintenance manual should provide complete and accurate information to meet
your operating and/or service requirements based on the information available at the time of
publication. The information in this manual may not cover all operating details or variations or provide
for all conditions in connection with installation, operation and maintenance. Should questions arise
which are not answered specifically in this manual, contact your equipment supplier.
Siemens reserves the right to make engineering refinements that may not be reflected in this manual.
The material in this manual is for informational purposes and is subject to change without notice.
Proprietary Rights Statement
This manual discloses information in which Siemens has proprietary rights. Neither receipt nor
possession of this manual confers or transfers any right to the client, and by its retention hereof, the
client acknowledges that it will not reproduce or cause to be reproduced, in whole or in part, any such
information except by written permission from SIEMENS. The client shall have the right to use and
disclose to its employees the information contained herein for the purpose of operating and maintaining
the SIEMENS equipment, and for no other purpose.
In the event the content of this manual is altered or section/items are omitted during reproduction, in
whole or in part, and instructions or definitions within the reproduction result in personal injury to those
who follow the altered instructions, the burden of responsibility for personal injury falls solely on the
party who effects the reproduction.
Manual Revision History
Event Date Description
Original Publication
Rev 0
September 2011 Original publication
Rev 1 November 2011 Updated remarks on firmware in sections 3.2 and 5
Updated Figure 23
IONPURE ®
G2 DISPLAY BOARD – IP-POWERDSP-G2
IP-POWERDSP-G2MAN Rev 1 Page 5 of 25
1 Introduction
1.1 Caution and Warning Messages
WARNING and CAUTION labels are used to attract attention to essential or critical information in
this manual. The labels are located to the left of the associated messages. Caution and Warning
messages will be located immediately before related text.
Warnings indicate condition, practices, or procedures that must be
observed to avoid personal injury or fatalities.
Cautions indicate a situation that may cause damage or destruction of
equipment or may pose a long-term health hazard.
Notes are also used to draw attention to information. Notes may be located before or after the
related text.
NOTE: Notes are used to add information, state exceptions, and point out areas that may be of
greater interest or importance.
1.2 General Description
Figure 1: G2 Display Board
The Ionpure® G2 Display Board IP-POWERDSP-G2 is a digital controller designed specifically to
function as the human interface that allows an operator to control and monitor the Ionpure
G2 DC
Power Controller IP-POWER600-G2.
IONPURE ®
G2 DISPLAY BOARD – IP-POWERDSP-G2
IP-POWERDSP-G2MAN Rev 1 Page 6 of 25
The display board employs a 20 X 4 LCD backlit display for a clear view of data under most lighting
conditions. Parameters can be adjusted and screens can be navigated using the four membrane
switches on the front panel. Once the parameters have been configured, the setup menu may be
locked out to require a four-digit password for further modifications.
One of the two RJ-45 ports available on the back of the unit is used for connection with the G2
power controller utilizing a Cat 6 cable, Ionpure
part numbers IP-CABLE50CM-G2 or IP-
CABLE2M-G2. One display board can independently operate up to sixteen G2 power controllers
when they are linked together in a daisy chain. No external power supply is required with the
G2 display board.
IONPURE ®
G2 DISPLAY BOARD – IP-POWERDSP-G2
IP-POWERDSP-G2MAN Rev 1 Page 7 of 25
2 Installation
2.1 Requirements
The G2 Display Board meets NEMA 4/IP65 requirements when properly installed. The unit is
intended to be mounted into an enclosed panel with the supplied gasket to provide a seal at the
panel cutout and it is secured from the back with the provided nuts.
The environmental limits for operation are 0 to 50 °C at up to 95% relative humidity
(non-condensing).
Consider the display’s dimensions shown in Figure 2 to select the proper size for the panel.
Figure 2: G2 Display Dimensions
All connections and settings in this section should be made without
energizing the power controller(s). Review other safety procedures prior to
working in the panel.
IONPURE ®
G2 DISPLAY BOARD – IP-POWERDSP-G2
IP-POWERDSP-G2MAN Rev 1 Page 8 of 25
2.2 Panel Mount
To mount the G2 display into a panel:
a. Prepare a cutout and four mounting holes in the door of the panel as shown in Figure 3. All
cutouts should be clean and free of burrs.
Figure 3: Panel Cutout Dimensions
b. Install the display board on the door of the enclosure using the supplied hardware and
gasket.
2.3 Connections
2.3.1 Connections to a Single G2 Power Controller
To connect the G2 display to a single G2 power controller:
a. Connect one end of a standard Cat 6 cable to one of the two RJ45 ports on the back
of the display.
b. Connect the other end of the cable to one of the two RJ45 ports on the G2 power
controller.
IONPURE ®
G2 DISPLAY BOARD – IP-POWERDSP-G2
IP-POWERDSP-G2MAN Rev 1 Page 9 of 25
c. Once the power controller is turned on, the display should power on.
Figure 4 illustrates the connections described above:
Figure 4: Connections to a Single G2 Power Controller
2.3.2 Connections to Multiple G2 Power Controllers
To connect the G2 display to multiple G2 power controllers:
a. Connect one end of a standard Cat 6 cable to one of the two RJ45 ports on the back
of the display.
b. Connect the other end of the cable to one of the two RJ45 ports on the first G2
power controller.
c. Use additional standard Cat 6 cables to daisy-chain other power controllers, as
shown in Figure 5.
d. Once any of the power controllers is turned on, the display should power on.
IONPURE ®
G2 DISPLAY BOARD – IP-POWERDSP-G2
IP-POWERDSP-G2MAN Rev 1 Page 10 of 25
Figure 5: Connections to Multiple G2 Power Controllers
2.4 Power Controller Setup
2.4.1 DC Output Current Range Selection
To limit the possibility of applying excessive current to a CEDI module, it is recommended to
select an appropriate output current range with DIP switch SW1 of the G2 Power Controller as
described in Figure 6. Select the current range that can limit the current closest to the
maximum value that could be required by the module. Table 3 of the G2 Power Controller
manual lists the maximum DC currents required by each module.
Figure 6: Current Range Selection DIP Switch
Ce manuel convient aux modèles suivants
1
Table des matières
