Evolution Evoflow TUF Manuel utilisateur

EVOFLOW

POOL AND SPA PUMPS

Installation and Operation Manual for

EVOFLOW POOL AND SPA PUMPS

TUF | TUF ECO-V | STREAM

This equipment must be installed and serviced by a qualied technician. Improper installation can create electrical

hazards which could result in property damage, serious injury or death. Improper installation will void the warranty.

This manual contains important information about the installation, operation and safe use of this product. Once

the product has been installed this manual must be given to the owner/operator of this equipment.

1.0 FOREWORD

1.1 Congratulations on your recent purchase of an Evolution Evoflow Pump. Please take a

moment to read through the entire manual before using the pump. The pump must be

installed and operated as specified.

2.0 ELECTRICAL SAFETY NOTICE

2.1 The electrical installation is to be done by a licensed electrician.

2.2 Each pump requires a circuit breaker to separate the pump from the electrical supply.

2.3 The contact separation has to provide full disconnection in all poles under over voltage

category III conditions.

2.4 If the pump is to be installed on a swimming pool or pond situation it is mandatory that

an earth leakage circuit breaker with a rated tripping current not exceeding 30mA be

installed.

2.5 Check the pumps nameplate for the following: Voltage, Amp draw and Cycle.

2.6 The power cord, including the ground wire shall have a qualityof 60245 IEC 66 (H07RN-F)

for models greater than 1kW power input.

2.7 For models less than 1kW input the quality shall be of 60245 IEC 57 (H05RN-F).

2.8 All installations must comply with local codes, based on IEC 60364-7-702 requirements.

3.0 ELECTRICAL CONNECTION

3.1 Check that the information on the nameplate corresponds to the power supply.

3.2 Employ a competent electrician to ensure wiring installation is made in accordance with

any local/national rules in the country where the pump is installed. The national wiring

rules in Australia & New Zealand is AS/NZS 3000.

3.3 Install and set the safety devices according to the current stated in the nameplate.

3.4 Single phase motors have a built in thermal overload switch.

4.0 SAFETY

4.1 The equipment mentioned in the manual is specially designed for the filtering and

recirculation of water in swimming pools.

4.2 They are designed to work with clean water at temperatures not exceeding 45°C (113°F).

4.3 The user should make sure that assembly and maintenance tasks are carried out

by qualified authorised persons and that these persons have first carefully read the

instructions for service and installation.

4.4 The installation should be carried out in accordance to the safety instructions of

swimming pools, especially Standard HD 60364-7-702, and the specific instructions for

each facility.

4.5 Follow any general safety rules or guidelines and any safety legislation and directives

given by local, state or national authorities.

4.6 Any modification of the pump requires the prior consent of the manufacturer. Original

replacement parts and accessories authorised by the manufacturer ensure a high

level of safety. The manufacturer of the pump assumes no liability for the damage and

injuries caused by unauthorised replacement parts and accessories.

4.7 During operation, some parts of the pump are subject to dangerous electric voltage.

Work may only be performed on the pump or on the equipment connected to it after

disconnection from power sources and after disconnecting the starting device.

4.8 The operating safety of the pump is only guaranteed if the installation and service

instructions are correctly followed.

4.9 The limit values stated in the technical table should not be exceeded under any

condition.

4.10 In the event of defective operation or fault, contact the manufacturer’s technical

support department or its nearest authorised agents.

4.11 If the supply cord is damaged, it must be replaced by an authorised service agent.

4.12 This appliance is not intended for use by children or persons with reduced physical,

sensory or mental capabilities or lack of experience and knowledge unless they have

been given supervision or instruction concerning the use of the appliance by a person

responsible for their safety.

5.0 GENERAL INSTALLATION

5.1 The pump must be located as close as practical to the pool. The pump must also be in a

position that enables easy access for periodic servicing.

5.2 Care must also be taken to position the pump in an area that is free from flooding in a

well-ventilated and dry location.

5.3 The pump motor cooling fan must have a minimum clearance of 150mm (6”).

5.4 The pump suction line should be not smaller than 40mm (1.5”).

5.5 The suction line is to have as few bends or elbows as possible. There must not be an air

trap on the suction line.

5.6 Use only the pump barrel unions supplied with the pump.

5.7 Ensure the pump is securely fastened to a level surface in the required position to

prevent movement.

5.8 The pump electrical cable must be wired for the proper voltage and rotation in

accordance with the wiring instructions.

5.9 All wiring and electrical work must be carried out by licensed electricians and installed

in accordance with applicable local codes.

5.10 The motor must be grounded.

5.11 The weight of the plumbing and fittings is to be independently supported and not

carried by the pump.

6.0 PRIMING

6.1 The pump will prime and reprime providing the hair and lint pot bowl is full of water and

there is sufficient supply from the suction point.

6.2 If you lose water from the hair and lint pot bowl, it will be necessary to refill it before

starting.

6.3 Remove the clear lid and fill the hair and lint pot bowl with water. Replace the lid,

ensuring the o-ring is correctly located.

6.4 Ensure all suction and discharge valves are open before you start the pump. Operating

the pump with these valves shut can damage the pump.

6.5 Start the pump.

6.6 Allow a few minutes (maximum) for the pump to start delivering water.

6.7 iWARNING: High suction lift or long suction lines will require additional time to prime

and can severely affect the performance of the pump. If the pump will not prime or

produce flowing water, repeat the steps above.

6.8 iWARNING: If allowed to run dry, mechanical seals can be damaged rapidly and may

need to be replaced.

6.9 Ensure that there is always adequate water in the hair and lint pot bowl before starting

the pump.

6.10 If you are unable to prime the pump see 8.0 Troubleshooting.

7.0 MAINTENANCE

7.1 The hair and lint pot should be inspected and cleaned at regular intervals.The procedure

for inspection and cleaning is as follows:

1. Remove the lid and lift out the hair and lint pot.

2. Remove debris and hose off with clean water if necessary.

3. Inspect the lid gasket, lubricate with silicon-based grease only if needed. If it is

damaged, replace.

4. Replace the hair and lint pot.

5. Reprime the hair and lint pot bowl.

6. Correctly locate the o-ring.

7. Replace the lid, hand tight only.

8. Switch on pump.

7.2 In climates where the pump may be exposed to frost or freezing, care must be taken

to ensure the pump is protected from damage. It is recommended that if the pump is

not used during this winter period, it should be drained completely. Drain plugs can be

supplied for this purpose. The winterising procedure is as follows:

1. Drain the pump.

2. Do not replace the drain plug. Store it in a safe place until you require the use of the

pump. An example would be within the hair and lint pot bowl basket.

3. If possible, remove the pump and store it in a dry location during this period.

4. When you reactivate the pump, ensure all seals and o-rings are in operational

condition and replace them if necessary—Regrease o-rings and gaskets with silicon-

based grease on refitting.

5. Check that the motor shaft moves freely before reactivation.

6. Reprime pump as per 6.0 Priming.

8.0 TROUBLESHOOTING

Fault/Problem Possible Cause Remedy

Pump will not

prime

Suction air leak.

Make sure water level is correct through suction points.

Ensure baskets and strainers are free of debris. Tighten all

ttings/unions on the suction side of the pump, remove and

replace mechanical seal.

No water in the pump. Make sure hair and lint pot is full of water.

Closed valves or blocked

lines.

Open all valves in system, clean skimmer and pump basket,

check pump impeller for blockage.

Motor will not run

No power to motor.

Check that all electrical switches are on. Ensure the circuit

breakers are properly set. Check if timer is set properly. Check

motor wiring at terminals.

Pump jammed. With power switched o, turn pump shaft (should spin freely).

If not contact electrician or Evolution for service.

Low ow

Dirty lter. Backwash lter or clean/replace cartridge lter element.

Dirty skimmer and pump

strainer. Clean skimmer and pump strainer.

Suction air leak. Refer to Pump will not prime.

Closed valve or blocked

line. Refer to Pump will not prime.

Motor runs hot

Be aware some heat from motors is normal. Do not touch hot motors. Thermal overload

protector will deactivate pump if there is an overload or high temperature problem.

Low or incorrect voltage. Supply to be corrected by electrician.

Cooling fan clearance. The pump motor cooling fan must have a minimum clearance

of 150mm.

Installed in direct

sunlight. Shield from the weather.

Poor ventilation. Do not tightly cover or enclose motor.

Noisy pump

operation

Bad bearing. Have electrician replace.

Air leak in suction. Refer to Pump will not prime.

Suction blockage. Locate and clear blockage.

Foreign matter in

impeller.

Dismantle pump and remove foreign matter and debris

from around impeller.

Cavitations.

Improve suction, reduce suction lift, reduce number of

ttings, increase pipe size, increase discharge pressure

and reduce ow by throttling discharge valve

Motor overload

cut outs

Motor not connected

properly. Have electrician check wiring.

Low incoming voltage. Have electrician check voltage, ensure pump is not running on

an extension cord. Report low supply to authorities.

Overload due to binding

in pump or wrong size

impeller.

Contact Evolution for service.

Evolution Water and Lighting Solutions

1/33 Hinkler Drive, Highland Park QLD 4211, Australia +61 7 5565 0000

Unless otherwise indicated, copyright in the content of this document is the property of Evolution Water and

Lighting Solutions under Australian copyright law. Unless otherwise indicated, content may not be reproduced

or transmitted without our prior written permission.

(W99188EV) 09/2022

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Evolution Pompe de piscine

Evolution

Evolution Evoflow Storm Eco-V Manuel utilisateur

Manuels Pompe de piscine populaires d'autres marques

TIP

TIP STEAM 35000 INV Schéma de câblage

Jacuzzi

Jacuzzi J-HI27C Manuel utilisateur

PoolRite

PoolRite SQI 400 Manuel utilisateur

Pentair

Pentair IntelliComm Manuel utilisateur

Calpeda

Calpeda NMP Manuel utilisateur

WilTec

WilTec 50374 Manuel utilisateur

AquaTools

AquaTools AT240701 Manuel utilisateur

Sibo

Sibo AquaForte RD352 Manuel utilisateur

CLS

CLS VICTORIA PLUS SILENT Manuel utilisateur

Pond One

Pond One Piranha 800 Manuel utilisateur

Hayward

Hayward VSP Manuel utilisateur

Resol

Resol DeltaSol B Pro Manuel utilisateur

Evolution Aqua

Evolution Aqua UniTech Perfect 5000 Manuel utilisateur

Outside Living Industries

Outside Living Industries Ubbink Heatermax Pool Guide de démarrage rapide

CPI

CPI Olympic 2P1815 Manuel utilisateur

Flotec

Flotec FP6121-01 Manuel utilisateur

Pentair

Pentair ONGA LEISURETIME LTP400 Manuel utilisateur

Polygroup

Polygroup SUMMER WAVES SKIMMERPLUS SFX330 Manuel utilisateur