Evikon PluraSens E2670-HFC Manuel utilisateur

PluraSens®

Flameproof

Refrigerant Detector-Transmitter

E2670-HFC

User Manual

E2670-HFC Rev 15.03.2023

Table of contents

Hydroﬂuorocarbons 3

Speciﬁcations 5

Product description 7

Safety requirements 7

Operating conditions 8

Installation guidelines 8

Mounting dimensions 10

Electrical connections 11

Correct and incorrect cabling for 24 VAC 13

Operation 14

Maintenance 14

Calibration 14

Delivery set 15

Order code for E2670-HFC options 15

Conﬁguring 16

Return to default settings 16

Modbus RTU Communication 17

RS485 communication interface 17

Communication parameters 17

Modbus holding registers 17

Warranty 22

Manufacturer contacts 22

E2670-HFC Rev 15.03.2023

Hydroﬂuorocarbons

HFCs are relatively non-ﬂammable, chemically stable, and nonreactive.

Classiﬁcation of halocarbon refrigerants

Group

Refrigerants

Chloroﬂuorocarbons (CFC)

R11, R12

Hydrochloroﬂuorocarbons

(HCFC)

R22, R141b, R142b

Hydroﬂuorocarbons (HFC)

R32, R125, R134a, R143a

Hydroﬂuorooleﬁns (HFO)

R1234ez, R1234yf, R1336mzz

Chlorine-containing refrigerants (CFC and HCFC) are considered to be damaging to the ozone layer

and contributing to the greenhouse effect. According to the Montreal Protocol, chlorine-containing

halocarbons should be completely dismissed and their manufacturing closed down.

Hydroﬂuorocarbons (HFC) contain no chlorine and are safer for the environment. Now

hydroﬂuorocarbons are the most commonly used halocarbon refrigerants.

Hydroﬂuorooleﬁns (HFO) is the last generation of refrigerants, more environmentally friendly than

HFCs, but moderately ﬂammable (A2L Class).

Properties of selected halocarbons

Name

Type

Components

Components weight %

Boiling point

R12

CFC

CCl F

2 2

100

−29.8 °C

R22

CFC

CHClF2

100

−40.8 °C

R125

HFC

CHF CF

2 3

100

−48.5 °C

R134a

HCFC

CF CH F

3 2

100

−26.2°C

R143a

HCFC

CF CH

3 3

100

-47.5 °C

R32

HFC

CH F

2 2

100

−52 °C

R1234yf

HFO

2,3,3,3-Tetraﬂuoropropene

100

-30 °C

R1234ze

HFO

1,3,3,3-Tetraﬂuoropropene

100

-19 °C

R404a

mixture

R125, R143a, R134a

44:52:4

−47.8 °C

R407c

mixture

R32, R125, R134a

23:25:52

−43 °C

E2670-HFC Rev 15.03.2023

R410a

mixture

R32, R125

50:50

−48.5 °C

Overexposure may cause dizziness and loss of concentration. At higher concentrations, CNS

depression and cardiac arrhythmia may result from exposure. Vapors displace air and can cause

asphyxiation in conﬁned spaces. At higher temperatures (>250°C) decomposition products may

include hydroﬂuoric acid (HF) and carbonyl halides.

An escape of refrigerant through a leak may damage the refrigerating facilities.

E2670-HFC Rev 15.03.2023

Speciﬁcations

Sensor type

Metal oxide semiconductor

Sampling method

Diffusion

Typical detection range

0...1000 / 2500 ppm

Resolution / digital unit

1 ppm

Response time T90

< 120 s

Sensor lifetime

> 5 years

Calibration interval

12 months

Signal update

Every 1 second

Power supply

12...36 VDC (default),

24 VAC or 230 VAC as options

Power consumption

< 2 VA

Analog outputs

2 × 4-20 mA / 0-10 V, user settable

Output scale width

> 10 × resolution

Recommended: 20-100% of the detection range

Outputs assignment

OUT1 2 gas; OUT2 2 gas

Load resistance

RL< (Us - 2 V) / 22 mA for 4-20 mA

RL> 250 kOhm for 0-10 V mode

Digital interface

RS485, Modbus RTU protocol

No galvanic isolation

Cable connections

Screwless spring-loaded terminals

Enclosure

Grey die-cast aluminium, wall mount, protection class IP65

Dimensions

H155 × W145 × D110 mm

H155 × W155 × D110 mm (with one cable gland)

H155 × W165 × D110 mm (with two cable glands)

Protection

Flameproof, ATEX: II 3G Ex d IIC T6 Gc

II 3D Ex tb IIIB Ip65 T85°C Dc

ATEX Approvals

Enclosure:

ATEX / IECEx

FTZU 03 ATEX 0207U

IECEx FTZU 12.0017U

II 2 G Ex db IIC Gb

II 2 D Ex tb IIIC Db

E2670-HFC Rev 15.03.2023

Glands:

ATEX / IECEx

EESF 19 ATEX 023X

II 2G Ex db IIC Gb

II 2D Ex tb IIIC Db IP66

CE marking

According to 2014/30/EU and 2014/34/EU,

EN 61000-6-3:2020, EN 61326-1:2013 (EMC, Emissions)

EN 61000-6-1:2019, EN 61000-6-2:2019, EN 61326-2-1:2013 (EMC,

Immunity)

EN 60079-0:2018, EN 60079-1:2014, EN 60079-31:2014,

EN 60079-29-1:2016, EN 60079-29-2:2015, EN 60079-29-3:2014

Operating conditions

-30...+60 °C; <95% RH non-condensing, 0,9...1,1 atm

Explosion-safe zones and ATEX Zones 2 and 22

Normal ambient oxygen level

Avoid exposure to corrosive gases, carbon disulﬁde or silicon containing

volatile products

Relay option

Output relays

2 × SPST relays (closing contact),

250 VAC / 30 VDC, 5 A max

Alarm set-points

Determined by the user within 5-95% of the detection range

E2670-HFC Rev 15.03.2023

Product description

E2670 is a series of ﬂameproof gas detectors-transmitters intended for operation in safe

zones and ATEX Zones 2 and 22. E2670 series devices are based on the PluraSens®

multifunctional platform and provide all its features. The instruments utilize gas sensors of

various types with excellent repeatability, stability, and long lifetime.

The E2670 series provides two independent analog outputs OUT1 and OUT2,

user-selectable to 4-20 mA or 0-10 V, proportional to gas concentrations. RS485 Modbus

RTU digital communication interface allows easy instrument conﬁguration and integration

into various automation systems.

The following features are available as an option:

●Two relays RE1 and RE2 with closing contacts. Relay outputs can be used to

switch alarm sirens, ventilation fans, shut-off valves, or other actuators,

●24 VAC or 230 VAC as options for power supply.

The version of your detector is marked on the package. If the symbol

⚠

is marked on the

equipment, consult the documentation for further information.

Safety requirements

Misuse will impair the protection of the product. Always adhere to the safety provisions

applicable in the country of use.

Do not perform any maintenance operation with the power on. Do not let water or foreign

objects inside the device.

Removal of the PCB from the enclosure voids the warranty. Do not touch the electronic

components directly, as they are sensitive to static electricity.

Connection diagrams can be found in the electrical connections section. The device might

not perform correctly or be damaged if the wrong power supply is connected.

It is crucial to tighten properly all the thread connections (screws, cable glands). Use ATEX

certiﬁed armored cables or cable conduits that are rated for use in the desired

environment.

A disconnecting device that is marked as such and easily accessible should be included in

the installation of this product.

The device should be properly earthed.

E2670-HFC Rev 15.03.2023

Operating conditions

The device should be used in a basic electromagnetic environment, where the latter is

deﬁned in EN 61326-1. Avoid strong mechanical shock and vibrations. Although E2670

series devices are suitable for use in the presence of ﬂammable dust, special precautions

should be taken when operating in a dusty environment. Dust may block the porous ﬁlter of

the sensor and compromise the results of the measurement. The detector should be

inspected regularly if used in a dusty atmosphere. Keep the instrument away from direct

sunlight. A sudden temperature or humidity change might affect the sensitivity of the

sensor. Make sure that installation and maintenance are performed in an explosion safe

atmosphere.

Installation guidelines

Before proceeding with the installation it is mandatory to read the Safety requirements

section and make sure to comply with all listed instructions. Installation standards EN

60079-29-2 and EN 45544-4 are also recommended for further instructions and related

information about the installation. During the installation of the detector-transmitter the

following points must be considered:

●Application (air quality control or leakage detection.)

●Properties of the space under investigation (room geometry, direction, and

velocity of airﬂows, etc.),

●Halocarbons are heavier than air and tend to sink. The sensor should be placed

near the ﬂoor.

●The device should be accessible for maintenance and repair.

The aforementioned conditions above will affect the coverage area of the device. However,

the coverage area for a detector-transmitter is usually between 2.5 to 5 meters radius.

For early leakage detection, install the sensor as close as possible to the potential leakage

sources (ﬂanges, valves, pressure reducers, pumps, etc.), taking into consideration other

points listed above.

For general area monitoring without deﬁnite leakage sources, the detectors should be

distributed evenly in the room.

For personal safety control, the detectors are installed in the breathing zone (at the height

of the head of people or animals). The recommended sensor position is vertical, pointing

downwards.

E2670-HFC Rev 15.03.2023

The device is ﬁxed on the wall using two ﬁxing holes located outside the sealed area of the

device (see dimensional drawing). Unscrew four lid screws and detach the lid from the

detector. Fix the detector on the wall and earth the enclosure using an earthing terminal on

the side of the device.

NOTE! Never perform installation or maintenance in an explosive atmosphere!

E2670-HFC Rev 15.03.2023

Mounting dimensions

Mounting holes

Table des matières

Autres manuels Evikon Capteur de sécurité

Evikon

Evikon E2610-LEL Manuel utilisateur

Evikon

Evikon PluraSens E2608-NH3 Manuel utilisateur

Evikon

Evikon PluraSens E2608-NH3-P Manuel utilisateur

Evikon

Evikon PluraSens E2670-VOC Manuel utilisateur

Evikon

Evikon PluraSens E2670-ETO Manuel utilisateur

Evikon

Evikon PluraSens E2638-LEL Manuel utilisateur

Evikon

Evikon E2610-VOC Manuel utilisateur

Evikon

Evikon PluraSens E2670-NH3-E Manuel utilisateur

Evikon

Evikon E2610-NH3 Manuel utilisateur

Evikon

Evikon E2630-HFC Manuel utilisateur

Evikon

Evikon E2618-PID Manuel utilisateur

Evikon

Evikon PluraSens E2648-ETO Manuel utilisateur

Evikon

Evikon PluraSens E2670-CO2 Manuel utilisateur

Evikon

Evikon PluraSens E2658-VOC Manuel utilisateur

Evikon

Evikon PluraSens E2670-C2H4 Manuel utilisateur

Evikon

Evikon PluraSens E2670-NH3-P Manuel utilisateur

Evikon

Evikon PluraSens E2608-CO2 Manuel utilisateur

Evikon

Evikon E2610-HFC Manuel utilisateur

Evikon

Evikon PluraSens E2670-O3 Manuel utilisateur

Evikon

Evikon PluraSens E2638-HFC Manuel utilisateur

Evikon

Evikon PluraSens E2658-CH4 Manuel utilisateur

Evikon

Evikon PluraSens E2670-SO2 Manuel utilisateur

Evikon

Evikon PluraSens E2638-O2 Manuel utilisateur

Evikon

Evikon PluraSens E2648-O3 Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur