EVERSPRING EVRESP816 Manuel utilisateur

Everspring

OUTDOOR MOTION DETECTOR

SKU: EVRESP816

Quickstart

This is a secure Motion Sensor for Europe. To run this device please insert fresh 3 * AA 1,5V batteries. Please make sure the internal battery is

fully charged. To add this device to your network execute the following action:

Press the tamper switch 3 times within 1.5 seconds to put the unit into inclusion mode.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart

section. (For more information about frequency regulations please refer to the frequency coverage overview at Sigma Designs Website ).

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication)

and every mains powered node can act as a repeater for other nodes (meshed network) in case the

receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-

Wave device regardless of brand and origin as long as both are suited for the same frequency

range.

If a device supports secure communication it will communicate with other devices secure as long as

this device provides the same or a higher level of security. Otherwise it will automatically turn into a

lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

The SP816 Outdoor Motion Detector is a Z-Wave Plus enabled device and is fully compatible with any Z-WaveTM enabled network. The device can be set

up in a Z-wave network to communicate directly with other end devices such as lighting controllers, or to report directly to a Z-wave controller (usually a

gateway).

This motion detector is primarily designed for outdoor lighting control application. It features a PIR motion detector to detect movement in a protected area

and a lux sensor for determining brightness of its surroundings. It comes with a built in timer to set the duration for light turn on. The lux level and the timer

can be set through knobs on the device itself.

If the PIR detects motion when lux level falls below a preset setting, the device will transmit a signal to turn on the outdoor lighting (or indirectly through

gateway) and then later turns it off when its timer has elapsed.

This device can also be used as a basic motion sensor for indoor security

application.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

1 Front Cover

2 Motion Sensor

3 Time-off / Lux Knob

4 LED indicator (hidden behind lens)

5 Battery

6 Rear Cover

7 Tamper Switch

Prepare for Installation / Reset

Please read the user manual before installing the product.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You

can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is

recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is

inoperable.

1. Press the tamper switch 3 times within 1.5 seconds to put the unit into exclusion mode.

2. Within 1 second of step 1, press the tamper switch again and hold until LED is off (about 5 seconds).

3. Node ID is excluded. The device reverts to factory default state and will be in auto-inclusion mode for 4 minutes.

Safety Warning for Batteries

The product contains batteries. Please remove the batteries when the device is not used. Do not mix batteries of different charging level or different

brands.

Installation

1. Use the rear cover to mark the two mounting holes.

2. Drill the holes, insert the plastic wall plugs and screw the rear cover to the wall using the screws supplied.

3. Assemble the detector back to its rear cover using screws as originally supplied.

4. The detector will enter Normal mode after 10 seconds.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate

with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave

network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right

on the device.

Inclusion

Press the tamper switch 3 times within 1.5 seconds to put the unit into inclusion mode.

Exclusion

Press the tamper switch 3 times within 1.5 seconds to put the unit into exclusion mode.

Auto-Inclusion

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Beside the standard inclusion this devices supports the so called auto inclusion. Right after powering up the device remains in inclusion state and can be

included by (any) gateway without further actions on the device itself. The auto inclusion mode will time out after some time.

Product Usage

Warm-Up

It will take approximately 1 minute for the detector to warm up after a battery is inserted. During this period the LED behind the lens will turn on. When the

LED turns off, it implies warm-up procedure is complete and the detector is ready for detection.

Note:

- This will not affect the Inclusion/Exclusion process.

- After removing batteries, wait for 5 seconds to refit batteries.

Quick Test

1. With the tamper switch not being pressed, the unit will enters Test mode to allow the user to test the device before it is mounted on the wall.

2. During Test mode, if movement is detected, the LED on the detector will illuminate implying the unit is working properly.

3. To exit the Test mode, simply press the Tamper switch for more than 10 seconds to enter Normal mode.

Mounting the Detector

Choosing the location

The recommended location for the detector is outside the house under the eaves or other shaded areas where it is not directly exposed to sunlight. Though

the detector is waterproof (IP44 rated), avoid direct contact with rain.

- Do not position the detector facing a window or direct sunlight.

- Do not position the detector directly above or facing any source of heat, eg: fires, radiators, boiler etc.

- Where possible, mount the detector so that the path of an intruder would cut across the fan pattern rather than directly towards the detector.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Mount the detector 2m from the floor. At this height, the detector will detect movement within its 100 degrees fan-shaped detection pattern up to 6-

12m depending on adjustment.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Walk Test

The user can perform a walk test to ensure the detector’s detection range falls within the desired area of coverage. This test also checks if the detector is

still within the communication range of the controller. For this test, the detector needs to be configured to turn on a connected lighting or other observable

action set using the controller.

1. On the detector, turn both knobs Time-Off and Lux to the “T” mark.

2. Walk into the detector’s range and check if the connected lighting turns on and off.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

3. If necessary, tilt the head of the detector to achieve desired result.

Operation

When the detector is mounted on the wall, i.e. tamper switch is pressed, for more than 10 seconds, it will enter Normal mode.

- Upon motion being sensed, the detector will turn ON the connected lighting. After the elapse of preset time-off, the detector will turn OFF the connected

lighting (see Time adjustment knob below).

- In Normal mode, the red indicator LED on the detector will not illuminate when the detector is triggered in order to conserve battery life, unless the battery

is low.

- If the Tamper switch is released, the detector will send a Notification command

(1) Time adjustment

Time-off knob controls how long the connected lighting will stay on after the motion is detected. It can be set from 5 seconds to 12 minutes.

(2) Lux adjustment

The LUX adjustment sets the brightness level threshold that will activate the motion sensor in the detector.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

For instance, turning the LUX knob clockwise to the MOON position will activate detector’s motion sensor only night and inactivated during the day. The

adjustable Lux range is about 30 - 200 Lux.

To set the lux level:

1. Turn the Time-off knob to “T” for maximum response.

2. Turn the LUX control knob to the edge clockwise at the “moon” (dusk) position.

3. Wait until the ambient light level reaches the level of darkness at which you wish the detector to activate.

4. Slowly rotate the Lux knob while anti-clockwise while keep creating motion during the process until the detector sends out a signal to turn on

the connected lighting. At this position the light should become operative at approximately the same level of darkness each evening

5. Set the Time-off knob back to the desired preset time.

Maintenance

Low Battery: When the battery becomes low, the LED will flash for 1 second when motion is detected in Normal mode to indicate low battery condition to

the user. When the battery becomes low in Test mode, the LED will flash once every 30 seconds.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

1. Make sure a device is in factory reset state before including. In doubt exclude before include.

2. If inclusion still fails, check if both devices use the same frequency.

3. Remove all dead devices from associations. Otherwise you will see severe delays.

4. Never use sleeping battery devices without a central controller.

5. Dont poll FLIRS devices.

6. Make sure to have enough mains powered device to benefit from the meshing

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Table des matières

Autres manuels EVERSPRING Capteur de sécurité

EVERSPRING

EVERSPRING SP817 Manuel utilisateur

EVERSPRING

EVERSPRING HSP01-0 Manuel utilisateur

EVERSPRING

EVERSPRING SM103 Manuel utilisateur

EVERSPRING

EVERSPRING SP814 Manuel utilisateur

EVERSPRING

EVERSPRING ST812 Manuel utilisateur

EVERSPRING

EVERSPRING HSM01 Manuel utilisateur

EVERSPRING

EVERSPRING EVR HSP02 Manuel utilisateur

EVERSPRING

EVERSPRING HSM02 Manuel utilisateur

EVERSPRING

EVERSPRING ES34T Manuel utilisateur

EVERSPRING

EVERSPRING SP103 Manuel utilisateur

EVERSPRING

EVERSPRING SP103 Manuel utilisateur

EVERSPRING

EVERSPRING SM201 Manuel utilisateur

EVERSPRING

EVERSPRING HSP02 Manuel utilisateur

EVERSPRING

EVERSPRING SE812 Manuel utilisateur

EVERSPRING

EVERSPRING SP816 Manuel utilisateur

EVERSPRING

EVERSPRING ST802 Manuel utilisateur

EVERSPRING

EVERSPRING ES160 Manuel utilisateur

EVERSPRING

EVERSPRING ST802 Manuel utilisateur

EVERSPRING

EVERSPRING SP815 Manuel utilisateur

EVERSPRING

EVERSPRING SP819 Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur