Evergreen twinkly pre-lit tree Manuel
pre-lit tree
INSTRUCTIONS GUIDE
attention
Class B Disclaimer: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
Please note that changes or modifications of this product not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Set up the tree according to the number tag sequence attached to each tree section from the bottom to the top.
Section #1 from the bottom on the tree stand, followed by Section #2 on top, and so on. Random setup will result in electrical malfunction.
WARNING!
1. This product may potentially trigger seizures for people with photosensitive epilepsy when using the motion effect light modes.
2. The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
3. Do not connect the chain to the supply while it is in the packing.
4. The lamps are not replaceable.
5. Do not interconnect parts of this lighting chain with parts of another manufacturer's lighting chain.
6. Interconnection shall be made only by the use of the supplied connectors. Any open ends must be sealed-off before use.
7. The controller and remote controller (if included) can only be used with this product.
CAUTION! For indoor use only.
The crossed-out wheeled bin symbol indicates that the item should be disposed of separately from household waste. The item should be handed in for recycling
in accordance with local environmental regulations for waste disposal.
Power supply: see label
Technical Specifications
When using electrical products, basic precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
a) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to
a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
b) This seasonal use product is not intended for permanent installation or use.
c) Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
d) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
e) Do not let lamps rest on the supply cord or on any wire.
f) Unplug the product when leaving the house, or when retiring for the night, or if left unattended.
g) This is an electric product – not a toy! To avoid risk of fire, burns, personal injury and electric shock it should not be played with or placed where small children can reach it.
h) Do not use this product for other than its intended use.
i) Do not hang ornaments or other objects from cord, wire, or light string.
j) Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
k) Do not cover the product with cloth, paper or any material not part of the product when in use.
l ) The lamps of this product are not replaceable. Do not attempt to change or modify the lamps.
m) Read and follow all instructions that are on the product or provided with the product.
SAVE THESE INSTRUCTIONS.
IMPORTANT SAFETY INSTRUCTIONS
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
3
physical setup
12 3
4
c. d.
e. f.
1
2
3
5
1.
Note: Do not step on the tree stand legs during the setup.
This may deform the tree stand and may result in an unbalanced tree.
6
1. Assemble the tree as shown in pictures.
2. Plug the power adapter into an AC outlet.
The tree will illuminate with default effects.
3.
2. 3.
BUTTON
LED INDICATOR
• CONTINUOUS GREEN: Direct Wi-Fi mode, connected
• FLASHING GREEN: Direct Wi-Fi mode, no device connected
• CONTINUOUS BLUE: Home Wi-Fi network mode, connected
• FLASHING BLUE: Home Wi-Fi network mode, connection in progress
• FLASHING RED: Home Wi-Fi network mode, unable to connect
• LIGHT BLUE: SETUP MODE (Bluetooth ON)
• YELLOW: Firmware Update in progress
• CONTINUOUS RED: General error
• FLASHING WHITE: Reset procedure in progress
7
RAINBOW SNOW UPDOWN FIREWORKS GLOW
preset eects
Twinkly comes with 5 preset effects that may be used without downloading the app.
Simply plug in the tree to a power outlet, then press the button on the controller
to switch between the 5 preset effects.
Light arrangements vary by models
8
app download &setup twinkly
1. 3. 4.2.
1. Go to App Store/Google Play Store (or scan QR code).
2. Download and install the Twinkly app.
3. Launch Twinkly app.
4. Select GENERATION II controller for your tree. Follow the setup process on the app.
Note: All app illustrations in this document are a mere representation of the functionality
and may vary from the actual app visuals.
Choose your controller
Generation I
Generation II
Twinkly
9
connection modes
B. DIRECT Wi-Fi CONNECTIONA. HOME WI-FI NETWORK CONNECTION
Bluetooth
Bluetooth
Connecting...
5
sec
1. Twinkly uses Bluetooth for the setup process only. Wi-Fi connection is required for operation. You can use:
2. Select the correct light count of your tree and tap "Configure” to complete the connection to your Twinkly tree.
A. Home Wi-Fi network connection (recommended):
Connect with your home/office WiFi from the list of available networks.
B. Direct Wi-Fi connection:
Select “Twinkly_xxxxxx” WiFi from the list of available networks. Password:
Twinkly2019
(NOTE: the internet on your phone will not be available in this case)
1. 2.
SKIP SETUP
Configure your Twinkly
Please select the LED count of your Twinkly
If you’re not sure, please see the number under the
Twinkly controller
210 270 330
390 435 480
540
750
600 660
Configure
10
Table des matières
Autres manuels Evergreen sapin artificiel
Manuels sapin artificiel populaires d'autres marques
Trim a Home
Trim a Home TY-S6-250L Manuel utilisateur
Polygroup
Polygroup TG7600NVQC03 Manuel utilisateur
Sears
Sears Donner & Blitzen M44814 Manuel utilisateur
BETHLEHEM LIGHTING
BETHLEHEM LIGHTING 6.5’ Tinsel Tree Manuel utilisateur
Home Accents Holiday
Home Accents Holiday TG76P3D93L08 Manuel utilisateur
Polygroup
Polygroup TG76M3S45C02 Manuel utilisateur
Polygroup
Polygroup TG90P3693L00 Manuel utilisateur
Costway
Costway CM23595US Manuel utilisateur
Polygroup
Polygroup TV46M3ADVC05 Manuel utilisateur
Home Accents Holiday
Home Accents Holiday TG76P4C15D03 Manuel utilisateur
Polygroup
Polygroup TV46P7001X00 Manuel utilisateur
Holiday Living
Holiday Living TV40EH339C01 Manuel utilisateur
