EverAccess EFM-AL-1A Manuel utilisateur

User Manual

M-

-A

L-

-1

Volume

EverAccess

EVERFOCUS ELECTRONICS CORPORATION

EFM-AL-1A

Instruction Guide

1801 Highland Ave Duarte CA 91010

Phone 626.844.8888 • Fax 626.844.8838

form or by any means without written permission of the Everfocus Electronics Corporation.

Table of Contents

CHAPTER 1

Product Overview 1

Features 1

Parts List 1

Specifications 2

CHAPTER 2

Installing an Alarm Module into the Controller 3

CHAPTER 3

Terminal/LED Definitions 4

Alarm Module Terminal Definition 4

Alarm Module LED Definition 5

CHAPTER 4

Wiring 6

Connection to Alarm Input 6

Connection to Alarm Output 6

Notes 8

Product Overview

The EverAccess®Flex Series controller (part number: EFC-02-1A) incorporates

state-of-the-art technology and modular design to provide reliable performance, user-

friendly installation, expansion capabilities, and flexible but powerful configuration

options. The alarm module (part number EFM-AL-1A) is the alarm expansion unit

for the Flex Series Controller.

The alarm module provides 8 alarm inputs and 8 alarm outputs. With the expansion

alarm module and 4 door modules installed, the EverAccess Flex Series controller can

support up to 10 alarm inputs and 18 alarm outputs. The alarm module is installed in

a right to left cascading fashion. The features for the alarm module are listed in the

next section.

Features

¾Supports 8 alarm inputs

¾Supports 8 alarm outputs

¾Built-in transient voltage suppressor (TVS) to protect controller from electric

surge

¾Large durable relay, max current draw up to 2A at 30VDC

¾Built-in LEDs display the system status intuitively

Parts List

Please be careful when you unpack the box due to the electronics devices inside.

Check and make sure that you have all the items below inside the original box:

¾3 mm* 4mm screws (to mount the module to the controller)

If an item appears to have been damaged in shipment, replace it properly in its carton

and notify the shipper. If any items are missing, notify your Everfocus Electronics

Corp. Sales Representative or Customer Service. The shipping carton is the safest

container in which the unit may be transported. Save it for possible future use.

Chapter

In addition, the following EverAccess products are required for use with the door

module to achieve the correct functionality:

¾EverAccess Flex Series Controller (part number EFC-02-1A)

Specifications

Items Parameter

Input 8 alarm inputs

Relay output 8 alarm outputs

LED 2x4

Power supply Provided by the controller

Max current draw for relay outputs 2A

Installing an Alarm

Module into the Controller

The EverAccess Flex series controller can accommodate up to 4 door modules and 1

alarm module. The alarm module connects to the door modules in a cascading

fashion. It can be installed in any of the 5 available positions; the order of installation

of the door modules and alarm module does not affect the functionality.

The steps to install an alarm module are described below:

Figure 2.1 Install an alarm module into Controller

1. Connect the pins on the lower right corner of the new module to the connector

on the bottom left corner of the installed module. Make sure that the pins fit

snugly into the receiving module.

2. Secure the module to the controller base board using the three screws (provided

in the module package).

Chapte

Terminal/LED Definitions

The definitions of the module terminals are presented in this chapter.

Alarm Module Terminal Definition

There are 36 terminals on the alarm module. The positions and indexes are described

in Fig 3.1. The definitions are described in Table 3.1.

Fig. 3.1 Alarm Module Terminal Definition

The definitions of the alarm module terminals are defined in the following table:

Table 3.1 The definition of LEDs on the alarm module

No Terminal

name Function No Terminal

name Function

larm1_In

larm signal input 1 19

larm5_In

larm signal input 5

2 GND GND 20 GND GND

larm2_In

larm signal input 2 21

larm6_In

larm signal input 6

Chapter

larm3_In

larm signal input 3 22

larm7_In

larm signal input 7

5 GND GND 23 GND GND

larm4_In

larm signal input 4 24

larm8_In

larm signal input 8

larm1_NO

larm 1 output for normally-open 25

larm5_NO

larm 5 output for normally-open

larm1_COM

larm 1 output in common 26

larm5_COM

larm 5 output in common

larm1

larm 1 output for normally-close 27

larm5

larm 5 output for normally-close

larm2

larm 2 output for normally-open 28

larm6

larm 6 output for normally-open

larm2

COM

larm 2 output in common 29

larm6

COM

larm 6 output in common

larm2

larm 2 output for normally-close 30

larm6

larm 6 output for normally-close

larm3

larm 3 output for normally-open 31

larm7

larm 7 output for normally-open

larm3

COM

larm 3 output in common 32

larm7

COM

larm 7 output in common

larm3

larm 3 output for normally-close 33

larm7

larm 7 output for normally-close

larm4

larm 4 output for normally-open 34

larm8

larm 8 output for normally-open

larm4

COM

larm 4 output in common 35

larm8

COM

larm 8 output in common

larm4

larm 4 output for normall

-close 36

larm8

larm 8 output for normally-close

Alarm Module LED Definition

There are 8 LED indicators on each door module. The positions and indexes are

shown in Fig. 3.2. The definitions of the LED indicators are presented in Table 3.2.

Fig. 3.2 Alarm Module LED Definition

The definitions of LEDs on the alarm module are defined in the following table:

Table 3.2 The definition of the LED indication on the alarm module

LED Meaning LED Meaning

1 Alarm 1 5 Alarm 5

2 Alarm 2 6 Alarm 6

3 Alarm 3 7 Alarm 7

4 Alarm 4 8 Alarm 8

The alarm LED has four different indications:

Light off: No alarm alert for the alarmed zone.

Light flashes slowly: The alarmed zone is in the alert delay stage.

Solid light on: The alarm alert is on for the alarmed zone

Light flashes quickly: The alarmed zone is in danger; alarm signal is input

Wiring

This chapter will describe, in detail, how to wire the terminals in the door modules.

Connection to Alarm Input

The alarm signals other than the fire alarm and alarm input 0 are controlled by the

alarm module, which contains 8 alarm inputs and 8 alarm outputs. Using the 5th

channel alarm signal input as an example, the method to connect the alarm module to

the alarm sensor is shown in Fig. 4.1:

Alarm sensor

for alarm in 5

Alarm input

GND

Fig.4.1 Connecting alarm-sensor to controller

Connection to Alarm Output

The alarm module provides 8 alarm inputs and 8 alarm outputs. The user can assign

the corresponding relay status to the different events. There are three terminals:

COM, N.O and N.C. The wiring depends on the alarm device. Please read the user

manual of the external alarm devices before wiring. Using the 5th channel alarm signal

output as an example, the wiring is shown in Fig. 4. 2 and 4. 3.

Chapte

larm

module

N.O .

COM

N.O. termina

C.terminal Exteral

Alarm

Device

Fig. 4. 2 Normally open connection for alarm output 5

N.C.

COM N.C. terminal

C.terminal Exteral

Alarming

Device

Fig. 4. 3 Normally closed connection for alarm output 5

larm

module

larm

module

Table des matières

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur