Event Lighting SPLIT228RDM Manuel utilisateur

SPLIT228RDM

8-way DMX and RDM Splitter

USER MANUAL

For your safety, please read this user manual carefully before use.

Event Lighting reserves the right to revise the manual at any time. Information and specifications

within this manual are subject to change without notice. Event Lighting assumes no liability or

responsibility for any errors or omissions. Please consult Event Lighting for any clarification or

information regarding this item.

Version 1.0

www.event-lighting.com.au

Safety Instructions

WARNING

•Do not open this device, there are no user serviceable parts inside. Risk of electric

shock.

•Do not operate this device outdoors or in any location where dust, excessive heat, water

or humidity may affect it.

•Do not connect this device to a dimmer or rheostat.

•Do not operate this device at temperatures higher than 40°C (104°F).

Product Description

SPLIT228RDM is a rack mountable DMX and RDM splitter designed to optically insulate and

distribute two DMX inputs into eight outputs via 5-pin XLR connectors.

1: 5-pin DMX Signal Connector In (A-Amber). 7: Output Status Indicator.

2: Input Selection Button (A-Amber). 8: OLED Display and Controls.

3: 5-pin DMX Signal Connector In (B-Blue). 9: Power Switch.

4: Input Selection Button (B-Blue). 10: Powercon Power Connector In.

5: 8x 5-pin DMX Signal Connectors Out. 11: Fuse.

6: Input Signal Selector. 12: Ground Connection.

Installation

Rack

SPLIT228RDM has four holes on the rack ears that suit a 1RU rack mount.

www.event-lighting.com.au

Input

Use the input selector button to view the status of the selected input: Amber or Blue.

Press Up/Down to view incoming DMX signal values.

Assign Input Signals to Outputs

•Press one of the eight input signal selectors to view the input signal source.

•Repeatedly press one of the eight input signal selectors or press the Up/Down buttons to

switch the input source.

•The output’s LED indicator will light up green if it is assigned to the Amber input.

•The output’s LED indicator will light up blue if it is assigned to the Blue input.

www.event-lighting.com.au

Control Panel

A: Display

B: Up button

C: Left button

D: Home button

E: Down button

F: Right button

Main Menu Options

SPLIT228RDM will display the following screen upon start-up:

No DMX signal DMX signal present DMX Signal Weak

Press Left to enter the main menu. The following options will be displayed:

•Input A

•Input B

•Merge

•Outputs

•DMX Error Alarm

Press Up/Down to move the selection.

www.event-lighting.com.au

Press Right to enter the selected option.

Press Left to return to the previous screen.

Press Home to return to the main menu.

Input A/Input B

Use these options to select either Input A or Input B and adjust the settings of that input.

Press Up/Down to select one of the options:

•Mode

•Failure Behaviour

•Status Information

Press Right to enter the selected option.

Mode

Press Up/Down to select the desired DMX mode from the following options:

•DMX and RDM (SPLIT228RDM functions as a bi-directional RDM splitter)

•Classic DMX (SPLIT228RDM only receives DMX signals, disables RDM)

•DMX 40Hz Frame Int. (Frame integrity ON)

•DMX 30Hz Frame Int. (Frame integrity ON)

•DMX 20Hz Frame Int. (Frame integrity ON)

•DMX 10Hz Frame Int. (Frame integrity ON)

•DMX 40 Hz (Frame integrity OFF)

•DMX 30Hz (Frame integrity OFF)

•DMX 20Hz (Frame integrity OFF)

•DMX 10Hz (Frame integrity OFF)

Press Right to confirm the selection.

www.event-lighting.com.au

Frame Integrity

On –Incoming DMX data will be received and used as a whole package, providing smooth

performance, with a longer delay time.

Off –Incoming DMX data will not be used as a whole package, and SPLIT228RDM will react

immediately to DMX input adjustments, resulting in shorter delay times. However, not all

changes will be visible until a new DMX data package is loaded.

Failure Behaviour

This option determines how SPLIT228RDM reacts to a DMX signal error.

Press Up/Down to select from the following options:

•Off: SPLIT228RDM will black out the output.

•Hold Last Look: SPLIT228RMD will continue to display the last working DMX signal.

Press Right to confirm the selection.

Status Information

This option displays the currently active DMX channel, frequency, operation mode and any

assigned outputs.

Press Up/Down to view the incoming DMX signal values.

www.event-lighting.com.au

Merge

Mode

Use this option to configure Merge settings.

Press Up/Down to select from the following options:

•HTP: Highest level of source A OR B on a merged channel takes priority.

•LTP: Last changed level of source A OR B on a merged channel takes priority.

•A+B: Select the start address of the second controller. The address must be between 1

and 512. Source A starts at 1 and Source B starts at the selected address.

oExample: When using two 36 channel controllers, set A+B to 37. 1-36 will be

from source A and 37-72 will be from source B.

•Backup: Source A is higher priority until signal is lost.

Press Right to confirm the selection.

Frame Rate

Use this option to select the desired DMX refresh rate after a Merge is configured.

www.event-lighting.com.au

Press Up/Down to select from the following options:

•DMX 40Hz

•DMX 30Hz

•DMX 20Hz

•DMX 10Hz

Press Right to confirm the selection.

Failure Behaviour

This option determines how SPLIT228RDM reacts to a DMX signal error.

Press Up/Down to select from the following options:

•Off: SPLIT228RDM will black out the output.

•Hold Last Look: SPLIT228RMD will continue to display the last working DMX signal.

Press Right to confirm the selection.

www.event-lighting.com.au

Outputs

Use this option to display status information about the selected output.

Press Up/Down to select from the following options:

•Output 1

•Output 2

•Output 3

•Output 4

•Output 5

•Output 6

•Output 7

•Output 8

Press Enter to confirm the selection.

DMX Error Alarm

Use this option to select whether an alert should be displayed when a DMX output error is

detected.

Press Up/Down to select from the following options:

•Off

•On

Press Enter to confirm the selection.

www.event-lighting.com.au

Settings

Use this option to configure SPLIT228RDM.

Press Up/Down to select from the following options:

•Label: View and edit the display name of the unit.

•Information: Display the unit’s unique identifiers, software and firmware versions.

Press Enter to confirm the selection.

Table des matières

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur