5
■3 - SOLO MODE | LIVE MODE
■5 - TRICKS
- Left led is Green: Push the pedal to your max toe.
SAVE ►Hold Down «ACTIVE» for 2s. The controller
displays toE StorEd.
- Left led turn to red: Now push the pedal to your
min heel
SAVE ►Hold Down «ACTIVE» for 2s. The controller
displays HEEL StorEd.
The pedal max (toe) should not go to 99 during
ACCESS | Hold down «PSW + ACTIVE» for 2 seconds.
- If the yellow Solo Led is On, you’re in Solo Mode.
The controller displays U1. Left Led state devices:
Nothing: U1 | Green: U2 | Red: U3 | Green+Red: U4
- If the yellow Solo Led is O you’re in Live Mode. The
controller displays preset number like 2A.
In Solo Mode, you can control 4 devices separately
by switching between the 4 devices with «PSW»
Footswitch. «PSW» footswitch doesn’t send any Midi
messages in Solo Mode if you control more than 1
device. If you have only one device, PSW send Control
Change CC0.
In Live Mode, you can control 4 devices at the same
time. There is a full mode with all presets scrolling (1
to 99) and bank mode with 9 banks of 3 presets (1A
to 9C). The 27 presets can be fully customised, check
2B-Live mode Settings.
«PSW» = Bank up (from1to 9 )
«Active» Preset A| «Down» Preset b| «Up» Preset C
By re-pressing on the same footswitch the eect is
bypassed (EvenMidi® send ProgramChange125 on
Eventide® corresponding to Bypass).
You can’t access to Looper Mode in Live Mode.
You can access to Looper if if the controller is in Solo
Mode and if you set your device to H9(& TimeFactor)
or Strymon Timeline. Check 2A-Midi Settings.
Set your Eventide H9 to load Looper Preset on
Program Change 127:
- For H9: Press Hotknob+Right Footswitch:
MIDI ► RCV.MAP ►127 . YourLooperPresetNumber.
- In H9 control App Pedal ► Midi Settings ► Program
calibration. Don’t worry it’s a normal behavior.
EXIT ►Press «PSW». The controller displays
rEturn.
Note: To prevent incorrect calibration, if the gap
between the 2 values is too short, the controller
displays too Short. Retry again.
Check Generic Device Settings on Annex page.
■2F- GENERIC DEVICE SETTINGS
MODES
1 - In Solo Mode hold down «DOWN» or «UP» for 1s.
to quickly scroll presets.
2 - You can quicky enable/disable Pots : hold down
«UP+DOWN» for 2s. The controller displays Pots
On or Pots OFF.
■4 - LOOPER MODE
Change Receive map ►Program Change 127 ►
YourLooperPresetNumber.
ACCESS | Hold down «ACTIVE» for 2 seconds. The
controller displays L1, L2, L3, or L4.
EXIT | Hold down «UP» for 2 seconds.
You can switch to other device by pressing «PSW»
Footswitch. Looper Mode is Stored. Check
1 - EVENTIDE® SETTINGS AND MIDI WIRING to set the
MIDI CC on the Eventide ® H9.
You can’t access to any settings in Looper mode.
■6 - WARRANTY
One year warranty for a normal usage. Don’t put it on
the water and do not apply an excessive voltage
(max 12V). If the warranty time is over we can x your
controller at your charge.
■7 - MAINTENANCE
You normally don’t have any maintenance. Clean the
controller with a damp cloth.
■8 - CONCLUSION
Well it’s time to play! Hope EvenMidi controller will t
perfectly on your pedal board. Have fun!
Franck Graziano - EvenMidi
EvenMidi® is a trademark by Webrox. Eventide® is a trademark by Even-
tide inc. Strymon® is a trademark by Damage control inc and Digitech®
is a trademark by Harman inc . EvenMidi has no connection or aliation
with Eventide® inc. The TimeFactor PitchFactor ModFactor and Space
products are eects created by Eventide®. The Timeline, Mobius and
BigSky are Strymon® products. The Whammy® is a Digitech® product.
