Eve Audio SC Series Manuel utilisateur

EVE AUDIO PRODUCT MANUAL

EVE AUDIO 产品说明书

Dec 2022

2022

年

月

SC2070

SAFETY INSTRUCTIONS 安全须知

To avoid the risk of electrical shock, do not attempt to open the unit. There are no user-serviceable parts inside.

Do not attempt to service the equipment yourself. In case of problems, please contact your local dealer or

distributor.

为避免触电，请勿试图打开箱体。箱体内没有可供用户自行维修的元部件，请勿尝试自行修理产品。如遇

到问题，请联系当地经销商或代理商。

This unit should be connected to a grounded power outlet. If you use extension cords and power distributors they

should be grounded as well.

此产品所连接电源插座应该接地。假如您使用的是外接线和配电器，那么请确保它们也是接地的。

Verify that the specified operating voltage on the rear side matches the local mains voltage. If these values do not

match you will have to adjust the loudspeaker setting appropriately and change the fuse type.

请确保产品背面上标注的操作电压符合使用环境当地电压。假若两者电压不匹配，请调整音箱设定并更换

保险丝。

Use only the fuse types specified on the rear side of the unit. Never bypass the fuse.

请使用产品背面上标注的保险丝类型，不要忽视保险丝。

Make sure that no liquids wet the inside of the cabinet. Never spray, pour or spill liquids directly onto the unit.

请避免液体弄湿箱体内部。请不要直接喷洒、灌注或泄漏液体在产品表面。

Do not use a wet cloth nor flammable or acid chemicals for cleaning.

请勿使用湿布、可燃或酸性化学试剂清洁产品。

Do not touch the diaphragms of the loudspeaker and do not obstruct the bass reflex ports.

请勿触碰单元的振膜，也不要遮挡低音反射端口。

Make sure there is enough air flow behind the loudspeaker to maintain the electronic components cool.

请确保音箱后方留有足够空气流动区域，以维持电子元件的正常温度。

Do not expose this product to extreme temperatures.

请勿将产品置放于极端温度环境下。

The diaphragms build up a magnetic field around the loudspeaker.

振膜会在音箱周围建立起一个磁性区域。

High sound pressure levels can damage your hearing permanently! Avoid standing close to loudspeakers producing

high sound pressure levels.

高强度的声压级会对您的听力造成永久性损坏！在大音量播放时请避免离音箱过近。

EVE Audio product manual

EVE Audio 产品手册

TABLE OF CONTENTS 目录内容

INTRODUCTION 介绍.................................................................................. 4

QUICK START 快速启动 ...............................................................................5

2.1.

First Steps 初始步骤 ................................................................................................... 5

2.2.

Speaker Connection

扬声器连接

................................................................................5

2.3.

Powering On

开机

........................................................................................................ 5

OPERATION 操作 ........................................................................................ 6

3.1.

First Steps 初始步骤.....................................................................................................6

3.2.

Operating Modes 运行模式 ........................................................................................7

3.3.

Powering on/off: Standby Mode

开/关机：待机模式

........................................... 7

3.4.

Volume Mode 音量模式 ............................................................................................. 7

3.5.

Settings Menu 设置目录 ............................................................................................. 9

3.6.

Filters 滤波器 ...............................................................................................................9

3.7.

Low Filter

低通滤波器

................................................................................................ 9

3.8.

High Filter

高通滤波器

............................................................................................. 10

3.9.

Mid Filter 中值滤波器............................................................................................... 10

3.10.

Desk Filter 桌面滤波器..............................................................................................11

3.11.

LED Mode

LED 模式

.................................................................................................11

3.12.

Saving Your Settings

保存设置

................................................................................. 12

3.13.

Power Switch 电源开关............................................................................................. 12

3.14.

DIP Switches

DIP 开关

............................................................................................. 13

3.15.

Mains Voltage Selector主电压选择器...................................................................... 13

3.16.

Power Connector (IEC) 电源连接器（IEC）......................................................... 13

POSITIONING 摆位....................................................................................14

4.1.

Speaker Positioning + Rubber Feet

扬声器位置+橡胶脚垫

................................. 14

4.2.

Height and Distance

高度和距离

.............................................................................15

4.3.

Stereo Setup 立体声设置.......................................................................................... 15

4.4.

Stereo Setup + Subwoofer (2.1)

立体声设置+低音炮（2.1）

........................... 16

4.5.

Multichannel Setup (5.1) 多通道设置（5.1）........................................................17

4.6.

Mixer/Workplace Reflections 调音台/工作场所反射............................................18

4.7.

Room Acoustics

室内声学

........................................................................................ 19

TECHNICAL SPECIFICATIONS 技术参数 ...............................................20

DECLARATION OF CONFORMITY 符合标准声明 .................................21

WARRANTY 保修........................................................................................22

1.INTRODUCTION

Th ank you for your time and int erest in the EV E Audio product ra nge.

非常感谢您对 EVE Audio 产品所给予的兴趣和付出的时间。

EV E Aud io is a loudspeaker manufacturer based in Berli n, Germany , that sp ecializes in the

development and de sig n of un ique studio monito rs.

EVE Audio 是一家基于德国柏林的音箱制造商，专注于设计和研发独特的录音室监听。

Th e us e of first-class compon ents is ou r hig hest priority beca use we firml y beli eve thi s is the

only way to manufactu re fir st-c las s produc ts.

使用最优质的元件是我们生产的第一要求，我们坚信这是制造最高质量产品的唯一途径。

Yo u have chosen a loud speaker from our Silvercon e SC se ries. Th e SC2070 was conceived as a

two-wa y system . The features all ow multipl e applic ations for use in prof essi onal reco rding

st udios as well as home studios.

您选择的是我们 SilverCone SC 系列。SC2070 被设计为双分频系统，产品特性可以让其在专业录音室和家庭

录音室中使用。

Th e SC2070 combines a 6.5 ” Silve rCo ne chas sis with the Air Motio n Tran sformer developed by

EV E Audio fo r the RS series . The loudspea ker sys tem is complet ed by hig h-performance

amp lif ier s and high- resolution DSP te chno log y. The woofer of the SC2070 is powered by a

dedica ted 15 0W amplifie r, while the tweeter is fed by a 100W amplifier.

SC2070 结合了一个 6.5 英寸的 SilverCone 低音单元，以及 EVE Audio 为RS 系列产品研发的 Air Motion

Transformer（气动高音头）。扬声器系统由高解析度 DSP 芯片支撑。SC2070 的低音单元由一个专业150

瓦功放供电，高音单元则是一个100 瓦的功放支持。

We wish you enjo y your new EVE Audio monit or. If you have any questions regardin g our

products, do not hesitate to contact your nearest deal er or get direc tly in touch with us... We

will be more than happy to help you out !

衷心希望您对 EVE Audio 监听感到满意。若有任何产品相关的疑问，请联系离您最近的经销商，或直接与

我们联系。我们非常愿意对您提供帮助！

Al l the best fro m Berli n.

来自柏林的美好问候。

Th e EVE Audio Team

EVE Audio 团队

2.QUICK START 快速启动

If you alrea dy have experi ence with stud io monitors, the Quick Start guide ought to be more

than enough to get you started.

假如您有使用录音室监听的经验，那么快速启动指南应该可以让您获得除简单操作以外更多的内容。

Fo r un ex pe ri en ce d us er s we re com me nd re ad i ng th e wh ol e us er ’ s ma nu al in or der to pr ev en t

any misuse.

对于零经验的用户，我们建议您阅读整本用户手册，以防止任何误操作。

2.1 First Steps 初始步骤

Ch e ck th e pac ka ge co mpon en ts (l ouds pea ke r, us er ’ s ma nua l, po wer co rd, g ri d , rubb er fe et ).

检查包装内的原件（扬声器、用户手册、电源线、网格、橡胶脚垫）。

Ch e ck th e vol tag e se t ti ng (s ee “ Ma in s V ol ta ge Sel ec to r ”).

检查电压设置（参见 "电源电压选择器"）。

Ch eck the set ting of the DIP Switc hes (var iab le).

检查 DIP 开关的设置（可调）。

2.2 Speaker Connection扬声器连接

Co nnect on e of the monit or inputs on the rear side (RCA or XLR) to the line output of a

pla yba ck sour ce, for instance an audio interf ace. Th e outpu t level shou ld be as low as pos sible.

将后面板的其中一个监听输入（RCA或XLR）连接到播放源的线路输出，例如一个音频接口。输出电平应尽

可能的低。

2.3 Powering On开机

En gage th e Power swi tch on the rear si de of the loudspeaker to turn it on or of f.

按位于扬声器后面板的开关键，即可开启或者关闭扬声器。

Th e LE Ds around the Volume cont rol on the fr ont pane l will light up clockwise. If the LED on

the right en d is di mly lit, this indica tes that the louds peaker is in Sta ndby Mode. Press the

Volume contro l to turn the loudspeaker on. If you tur n the Volume control counter clockwise

until the LE D on the le ft end li ghts up dimly the loudspeaker will be muted.

环绕在前面板Volume音量旋钮的 LED 会顺时针亮起。如果右侧最底端的 LED 颜色较暗，则代表扬声器处于

Standby待机模式。单击Volume音量旋钮，开启扬声器。如果逆时针转动Volume音量控制旋钮，直至左侧

LED 颜色变暗，可以使扬声器静音。

In crease the out put leve l on the sourc e devic e until the LED ring starts to blink, then reduce

the output level a bit. The ma ximum operating level for the inp ut (i.e. the analog to digital

converter ) is now set opt imally. To set the desir ed listenin g vol ume use the Volume control on

the loudsp eaker.

增加音源或声卡的输出电平直至扬声器的LED 开始闪烁，然后减少一点音源的输出电平，最大的输入电平

（模拟至数字转换器）就被设置好了，这时可以随意使用扬声器上的Volume音量旋钮调节音量。

The LED ring indicates the volume setting. If the LED ring starts to blink, reduce the output level on the signal

source.

LED 灯环代表音量位置。如果 LED 环开始闪烁，请降低信号源的输出电平。

Analog Input 模拟输入

Unbalanced 非平衡

Volume 音量

Filter 滤波器

Max. Input 最大输出

not used 未使用

locked 锁定

variable 可变

Balanced 平衡

Rear connectors & DIP switches

后面板的连接器和DIP开关

Check the package components (loudspeaker, user’s manual, power cord, grid, rubber feet).

检查包装内的原件（音箱、用户手册、电源线、橡胶脚垫）。

Check the voltage setting (see “Mains Voltage Selector”).

检查电压设置（详见“主电压器”章节）。

Check the setting of the DIP Switches (variable).

检查 DIP 开关的设置（可变）。

Connections: there are two input connectors on the rear side. These allow the connection of

balanced sources with XLR connectors or unbalanced sources with RCA connectors.

连接：在设备背面有两个输入接口，可以连接 XLR 插孔的平衡信号源或 RCA 插头的非平衡信号源。

•Pin assignment XLR: 1 = Shield, 2 = hot (+), 3 = cold(-).

Pin 分配 XLR: 1 = 屏蔽， 2 = 热（+），3 = 冷（-）

•Pin assignment RCA: Center conductor = Signal, Ring = Shield.

Pin 分配 RCA: 中心导线 =信号，环 =屏蔽

Both analog inputs can be used simultaneously, whereby the signals are summed.两个模拟输入可被

同时使用，信号将汇合至一起。

The maximum level of the source signal should not exceed 8dBu. If the input is overloaded the LED

ring will start blinking.

信号源的最大电平不应超过 8 dBu。若输入超载，则 LED 开始闪烁。

EVE Audio product manual

EVE Audio 产品手册

3.2 Operating Modes 运行模式

Standby Mode | Volume Mode (-10dB) | Setting Menu (Low filter @ -2dB)

待机模式|音量模式（-10dB）|设置菜单（低通滤波@-2dB）

3.3 Powering on/off: Standby Mode 开/关机：待机模式

Press and hold the control three seconds in order to put the monitor in Standby Mode. The volume

will decrease gradually while the LED ring lights up once around the Volume control. Afterwards,

the LED on the right end will light dimly and the power consumption is reduced to 1 watt.

按住按钮 3秒钟可进入”Standby Mode”待机模式。此时音量将逐渐降低，LED 圈将围绕音量旋钮依

次亮起。接下来位于最右侧底部的一格 LED 将会变暗，同时待机功耗将降低至 1瓦特。

！To exit the Standby Mode press briefly the Volume control once again. The level will increase

gradually.

再次单击Volume音量控制按钮，即可退出”Standby Mode ”待机模式，设备电平将逐渐增加。

3.4 Volume Mode 音量模式

•Level adjustment 电平调整

The maximum input level for balanced (XLR) and unbalanced signals (RCA)

is +7dBu or +22dBu, depending on the position of the Max. Input switch

on the rear panel (see DIP Switches). Higher levels produce distortion due

to the overloading of the analog to digital converter.

平衡信号(XLR)和非平衡信号(RCA)的最大输入电平是 +7dBu或+22dBu，这取决于最大输入开关的位置。

在后面板上的输入开关（见DIP开关）。由于模数转换器的过载，较高的电平会产生失真。

Given that some professional studio devices can produce in excess of

+22dBu, the LED ring will start blinking whenever the AD converter is

overloading. If that is the case, the output level of the source should be

reduced.

考虑到许多专业录音室设备的输出都高于 +22dBu，在 A/D 转换过载时LED 将开始闪烁。当这种情况

发生时，请减少声源的输出电平。

•

Volume adjustment

音量调整

Turn the knob to adjust the volume. Depending on the LED mode selected (see LED Mode), the volume will be

displayed as a dim/bright circle or as a dim/bright point.

转动音量旋钮对音量进行调整。根据所选择的 LED 模式（详见“LED 模式”），音量将会显示为微暗

/明亮的一圈或者是昏暗/明亮的点。

The control’s response curve is not linear. The increments become finer as the volume increases:

-80dB (minimum) to -48dB: 2dB

-48dB to -20dB: 1dB

-20dB to 0dB (maximum): 0.5dB

该控制器的反应曲线不是线性的。随着音量的增加，增量变得更精细：

-80dB（最小）到 -48dB：2dB

-48dB到-20dB：1dB

-20dB到0dB（最大）： 0.5dB

•Mute 静音

To mute the monitor, turn the Volume control counter clockwise until you reach the minimum level. When the LED

on the left end lights up dimly the Mute Mode is activated.

要静音监听，逆时针转动音量控制，直到达到最低电平。当左端的LED灯亮起时，激活Mute Mode 静

音模式。

! To exit the Mute Mode simply turn the control clockwise until you reach the desired volume.

要退出静音模式，只需顺时针转动控制器，直到达到所需的音量。

EVE Audio product manual

EVE Audio 产品手册

3.5 Settings Menu 设置菜单

Press the control once to enter the Settings menu. Here you can set four different filters (High, Mid,

Desk, Low), as well as the LED ring’s behavior. The LED of the currently active function will blink.

按控制键进入Settings设置菜单。在这里，你可以设置四个不同的滤波器（高频、中频、桌面、低

频），以及LED灯环的反应。当前激活的功能，LED灯会闪烁。

Turn the control to choose the filter or LED mode desired. The blinking LED indicates the function

selected while the steady-on LED indicates the value assigned to that function.

转动控制键，选择所需的滤波器或LED 模式。闪烁的LED代表所选的功能，而持续的LED代表分配给该

功能的数值。

Press the control to confirm your selection. The blinking will stop once the selection is confirmed.

按控制键确认你的选择。一旦选择被确认，闪烁将停止。

Turn the control to adjust the filter or the LED behavior.

转动控制器来调整滤波器或LED 的行为。

When you are satisfied with the setting, press the control again to go back to the Settings menu. You

can then select and edit another function.

当你对设置感到满意时，再按一下控制键，就可以回到Settings设置菜单。接着你可以选择和编辑另

一个功能。

！To exit the Settings menu press and hold the control for three seconds or simply wait 10 seconds.

The loudspeaker will then return automatically to the Volume Mode.

请按住控制键三秒钟，或仅等待10秒钟，可退出 "Settings"菜单。然后扬声器将自动返回到 Volume

音量模式。

3.6 Filters 滤波器

The filters of the EVE Audio monitors were specially developed to offer you the possibility of adjusting

your monitoring system to the characteristics of your room.

EVE Audio监听的滤波器是专门根据房间的特点，提供调整监听系统的可能性而开发的。

These filters help correct the alterations to the frequency response produced by the room acoustics

and listening distance. Do bear in mind that correcting bad room acoustics with filters will only

achieve average results. In any case, you should try to use the filters as little as possible.

这些滤波器有助于校正由房间声学特点和聆听距离所产生的频率响应的变化。请注意，房间声学很差，

用滤波器校正只能达到一般效果。在任何情况下，你都应该尽量少使用滤波器。

3.7 Low Filter 低频滤波器

The Low-Shelf Filter allows you to boost or attenuate frequencies below 300Hz in 0.5dB steps. Use this

filter whenever the acoustics of your room cause problems in the low frequency range.

低频滤波器可以以0.5dB为单位，提升或衰减300Hz以下的频率。当你房间的声学特性在低频范围内

引起问题时，就可以使用这个滤波器。

If the low frequencies are boosted by the room, you can attenuate them with the Low-Shelf Filter. The

reasons for this boost could be the room modes or the loudspeakers being too close to the walls. In

the same way, if the low frequencies are to weak, you can boost them to balance the frequency

response.

如果低频由于房间的声学被提升了，你可以用Low-Shelf低频滤波器来衰减调整它们。造成这种提升

的原因，可能是房间模式或扬声器离墙太近。同样地，如果低频太弱，你可以提升它们以平衡频率响

应。

3.8 High Filter 高通滤波器

The High-Shelf Filter allows you to boost or attenuate frequencies above 3kHz in 0.5dB steps. High

frequencies are affected depending on the distance from the sound source to the listening position.

The further you are from the loudspeakers, the weaker the high frequencies. In such cases the filter

should be set to boost them. In desktop applications, distances can be as short as 1m (3ft), which

results in the high frequencies being boosted. To compensate for this effect you should use the High-

Shelf Filter to attenuate the high frequencies.

High-Shelf Filter 高通滤波器可以以0.5dB的一步（的距离），提升或衰减3kHz以上的频率。影响高频，

与声源到聆听位置的距离有关。你离扬声器越远，高频就越弱。在这种情况下，应该设置滤波器为提

升。在桌面应用中，距离可以短至1米（3英尺），这样高频会提升。为了抵消这个效果，你应该削弱

高频。

If you have a very dead room, it might be wise to boost the high frequencies in order to have a more

balanced overall sound. When the listening position is too close to the loudspeakers or the room has

reflective surfaces, it is reasonable to attenuate the high frequencies.

如果是在消声室，提升高频可能有一个更平衡的整体声音。当聆听位置离扬声器太近，或房间有反射

面时，削弱高频是合理的。

3.9 Mid Filter

中频滤波器

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Eve Audio Intervenants

Eve Audio

Eve Audio SC207 Manuel utilisateur

Eve Audio

Eve Audio ThunderStorm TS110 Manuel utilisateur

Eve Audio

Eve Audio sc3010 Manuel utilisateur

Eve Audio

Eve Audio SC204 Manuel utilisateur

Eve Audio

Eve Audio SC4070 Manuel utilisateur

Eve Audio

Eve Audio SC204 Manuel utilisateur

Eve Audio

Eve Audio SC407 Manuel utilisateur

Eve Audio

Eve Audio SC3070 Manuel utilisateur

Eve Audio

Eve Audio SC305 Manuel utilisateur

Manuels Intervenants populaires d'autres marques

argon audio

argon audio IE20 Manuel utilisateur

Denon

Denon SC-N7 Manuel utilisateur

Gemline

Gemline Ace 3952 Manuel utilisateur

Focal

Focal ON WALL 300 Mode d’emploi

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manuel utilisateur

SoundLogic

SoundLogic BCCS-6/6395 Manuel utilisateur

Peavey

Peavey DTH 218 Manuel utilisateur

Avantree

Avantree Pluto Air Manuel utilisateur

Morel

Morel Integra Series INTEGRA OVATION 4 Manuel utilisateur

Oppo

Oppo SONICA Manuel utilisateur

Bose

Bose SoundLink Wireless Music System Manuel utilisateur

Rocksteady

Rocksteady Stadium Manuel utilisateur

Bowers & Wilkins

Bowers & Wilkins 4 Manuel utilisateur

Sonance

Sonance SONOS OUTDOOR Series Manuel utilisateur

Electro-Voice

Electro-Voice EVID FM4.2 Manuel utilisateur

Pioneer

Pioneer XW-HTD630 Manuel utilisateur

Onn

Onn BWA16AA002 Manuel utilisateur

HP GL313AA - USB Speakers PC Multimedia Manuel utilisateur