Evak DPC-10 Manuel utilisateur

www.evak-pumps.com

Vol.PMDPC-15051-1.2-R

DPC-10

Water Pump Digital Pressure Controller

Installation and Operation Manual

EVAK PUMP TECHNOLOGY CORP.

No. 551, Zhongshan Rd., Qingshui Dist., Taichung City 436, Taiwan.

TEL:+886-426-233556 Fax:+886-426-235559

EC DECLARATION OF CONFORMITY

Applicant : EVAK PUMP TECHNOLOGY CORP.

Address of Applicant : No.551, Zhongshan Rd., Qingshui Dist., Taichung City 436,

Taiwan (R.O.C.)

Product Name : Water Pump Digital Pressure Controller

Model No. : DPC-10

Test Report No.:

E14060543

Directive : 2004/108/EC Electromagnetic Compatibility Directive

For the most specific risks of this machine, safety and compliance with the essential

requirements of the Directive has been based on elements of:

EN 61000-6-3:2007/A1:2011 / Electromagnetic compatibility (EMC) -- Part 6-3: Generic standards -

Emission standard for residential, commercial and light-industrial environments

EN 55011:2009/A1:2010 / Industrial, scientific and medical equipment - Radio-frequency disturbance

characteristics - Limits and methods of measurement CISPR 11:2009 (Modified)

EN 61000-6-1:2007 / Electromagnetic compatibility (EMC) -- Part 6-1: Generic standards - Immunity

for residential, commercial and light-industrial environments

IEC 61000-4-2:2008/Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement

techniques - Electrostatic discharge immunity test

IEC 61000-4-3:2006+A1:2007+A2:2010/Electromagnetic compatibility (EMC) - Part 4-3: Testing and

measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test

IEC 61000-4-8:2009 / Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement

techniques - Power frequency magnetic field immunity test

Date :

Signature :

Qualification : General Manager

Place : Taichung City, Taiwan

EVAK PUMP TECHNOLOGY CORP.

No.551, Zhongshan Rd., Qingshui Dist., Taichung City 436, Taiwan (R.O.C.)

1.DPC-10 Panel introduction

2.Technical data

Supply voltage:115~220Vac ± 10% 50/60HZ

Maximum ambient temperature:+40℃

Maximum liquid temperature: +65℃

Maximum system pressure: 10bar

Maximum contact load AMP: 12A

Ingress Protection Rating: IP55

Dry Running

Digital Pressure Controller

DPC-10

bar

kg/cm

psi

Over Pressure

Power :115-220Vac ±10% 50/60HZ

Max :12A / Max :10bar / IP55

Model Number

LED Light

LCD Display

Technical Data

Button

Pressure Unit

Relay Capacity: 1HP in 110V or 2HP in 220V

The Max. motor size is 1HP in 110V or 2HP in

220V, but if connect to contactor in the control

panel then DPC-10 controller can fit the pump

over 2HP.

4.Button Function Introduction

3.Wiring diagram

Note:

L,N: Power Supply

W1,U1: Motor Wire

Blue,Brown: Controller Power Supply

Yellow,White: Controller Relay

WARNING Incorrect wiring could cause damage to the pressure controller,

confirm the color of the wires with the operation manual before wiring.

Button Icon Function

Browsing original pressure value.

Downward adjustment of the parameter value.

Pump start and stop operation.

Upward adjustment of the parameter value.

Possible with Button

Short press once:

Switch to Basic parameter setting.

Long press for 3 seconds:

Switch to Advance parameter setting.

After entering the parameter setting,short press once again:

Switch to next setting mode and enter the set value.

Blue

Brown

Yellow

Blue

White

Brown

Yellow

White

a. Single phase wiring connection

b. Three phase wiring connection-220V

c. Three phase wiring connection-380V

3 phase PUMP

AC 220V

Coil

DPC-10

Controller

White

Brown Blue

Yellow

U V W

3 3W AC 220V

R S T

3 phase PUMP

DPC-10

Controller

White

Brown Blue

Yellow

U V W

3 4W AC 380V

R S T N

NFB

(MCCB)

AC 220V

Coil

WARNING

!If connecting to a pump driven by 3ph/380V pump (Please

AC 110V,220V

NFB

(MCCB)

1 phase PUMP

DPC-10

Controller

White

Brown Blue

Yellow

NFB

(MCCB)

L N

If installing DPC-10 with a varistor, please connect varistor wire in parralled with

thin Brown and Blue wires of the DPC-10.

note the power voltage is not allowed over 400V.), the blue and yellow

wires of DPC-10 are forbidden connecting to R or S wire, otherwise the

DPC-10 controller will be burned out.

220V( <250V)

Note: If the voltage is over 250V, please add transformer by yourself.

WARNING

Any connection to the contactor, please add a

R.C capacitor (spark eliminator) to reduce the

possible electromagnetic interference.

WARNING

Any connection to the contactor, please add a

R.C capacitor (spark eliminator) to reduce the

possible electromagnetic interference.

5.The status of LED lights

6.Parameter display and settings

Item Light Message indication

Control loop off from the systemNon

Green

Orange

Red

Pump status

Control loop command the pump of

system to start running

Control loop is loaded into the system

Warning message to shut down the

system temporarily

Pump off

Pump on

Pump standby

Pump auto stop and display

the fault message(Dry running

Item

Parameter

Display

Code

Default

Unit

P-max kg/cm²

kg/cm²

P-min

P-Dry

Description

Pressure of

water shortage

setting display

(Dry running)

Min. Pressure

setting display

Max. Pressure

setting display

» Press once: To see the

Max.

pressure setting value.

» Or stay on this screen for 5 seconds it will return to

the actual pressure status display automatically.

» Press again: To see the Min. pressure setting value.

» Or stay on this screen for 5 seconds it will return to

the actual pressure status display automatically.

» Press again: To see the pressure

of water shortage

setting value.

» Or stay on this screen for 5 seconds it will return to

the actual pressure status display automatically.

“ ” (Pressure value display)

or Over pressure)

Item Parameter Pump action Description

Stop (OFF)

Restart (ON)

Pump off Non

Pump on Orange

Press once to restart the pump running.

Long press for 3 seconds to stop the pump

“ ” (Restart or stop the pump running)

“ ” (Short press once to enter Basic Setting Mode)

Setting procedure : Max. pressure →Min. start pressure →Time-Delay

Item

Parameters

Display

Code

Default

Unit

Data

Range

P-max kg/cm²

0.01~

10.00

Description

Max. pressure

setting

(high pressure)

a.Select to modify Max. Pressure, press the

left or right button to adjust the value, after

finishing the setting, press the SET button

once and go to Min. start pressure

running.

0~60

kg/cm²

sec

- -

P-min

Delay

loAd

Min. start

pressure setting

(low pressure)

Time-Delay

setting when

reaching the

Max. Pressure

Load for 3

seconds to store

setting value

b.Stay on this screen for 30 seconds, the

display screen will back to the actual

pressure conditions automatically and the

preset data value is not stored.

c.Choose not to modify the pressure, press

the SET button, and go to next parameter

setting.

a.Select to modify Min. start pressure , press

the left or right button to adjust the value,

after finishing the setting, press the SET

button once and go to Time-Delay setting .

b.Stay on this screen for 30 seconds, the

display screen will back to the actual

pressure conditions automatically and the

preset data value is not stored.

c. Choose not to modify the pressure, press

the SET button, and go to next parameter

setting.

a.Select to modify the Time-delay setting

when reaching the Max. Pressure, press

the left or right button to adjust the value,

after finishing the setting, press the SET

button and go to " loAd " display.

b.Stay on this screen for 30 seconds, the

display screen will back to the actual

pressure conditions automatically and the

preset data value is not stored.

c.Choose not to modify the delay time, press

the SET button, and LCD display " loAd "

Above setting value are stored and

3 seconds later, go to the actual pressure

value display automatically.

setting.

Light

0.01~

10.00

“ ” long press for 3 seconds (Advanced setting Mode)

Item

Parameters

Display

Code

Default

Unit

Data

Range

Unit - -

Description

Switch the

display working

pressure unit

a.Select to switch the Unit of working

pressure, press the right button to change

the pressure unit (Cycle : kg/cm² → Psi

→ bar→ kg/cm²), then press the SET

button once and go to next parameter

setting.

b.Stay on this screen for 30 seconds, the

display screen will back to the actual

pressure conditions automatically and the

preset data value is not stored.

c.Choose not to modify the working pressure

unit, press the SET button once, and go

to next parameter setting.

P-Dry sec 1~120

0.01~

10.00

P-Dry

Detection time

setting of water

shortage

Pressure of

water shortage

setting

(Dry running)

a.Select to modify the detection time after

reaching the pressure setting of water

shortage (Dry running),press the left or

right button to adjust the value, after

b.Stay on this screen for 30 seconds, the

display screen will back to the actual

pressure conditions automatically and the

preset data value is not stored.

c.Choose not to modify P-Dry detection time

setting, press the SET button once, and

go to next parameter setting.

a. Select to modify the Pressure of water

shortage, press the left or right button to

adjust the value, after finishing the setting,

press the SET button and go to next

b.Stay on this screen for 30 seconds, the

display screen will back to the actual

pressure conditions automatically and the

preset data value is not stored.

c.Choose not to modify the pressure of water

shortage, press the SET button, and go

to next parameter setting.

1~600sec

hour

Auto

Reset

Auto

Time setting of

automatic

re-start running

after warning

shutdown (Dry

running or

Over pressure)

(α value)

Auto shutdown

setting after

continuous

running

a.Select to modify automatic re-start time,

press the left or right button to adjust the

value, after finish the setting,press the SET

button, and go to next parameter setting.

The time of automatic re-start = (automatic

time setting) * (trip times)³

(Cumulative trip times is up to 10 times, if

press the right button to re-start, then the

trip times can be re-calculated.)

b.Stay on this screen for 30 seconds, the

display screen will back to the actual

pressure conditions automatically and the

preset data value is not stored.

c.Choose not to modify the automatic re-start

time, press the SET button, and go to next

parameter setting.

a.Select to modify the auto shutdown setting

after continuous running, press the left or

right button to adjust the value, after finish-

ing the setting, press the SET button and

go to next parameter setting.

St-0: Pressure controller keeps running

and won’t shut down automatically.

St-.5: Pressure controller will auto shut

down after continuously running 0.5 hours

and won’t auto restart after the shutdown.

St-1~5: Pressure controller will auto shut

down after continuously running 1~5 hours

and won’t auto restart after the shutdown.

finishing

the setting, press the SET button

kg/cm²

parameter setting.

Item

Parameters

Display

Code

Default

Unit

Data

Range

Description

and go to next parameter setting.

St-0

St-.5

St-1

St-5

b.Stay on this screen for 30 seconds, the

display screen will back to the actual

pressure conditions automatically and the

preset data value is not stored.

c.Choose not to modify the automatic re-start

time, press the SET button, and go to next

parameter setting.

7.Standard default value

(Factory preset settings)

8.Setting value range

a. Pressure setting range : 0.01 ~ 10.00bar

b. Time-Delay setting range : 0 ~ 60 seconds

c. Detection time after Dry-running setting range: 1~120 seconds

d. Time of automatic re-start running after warning shutdown

(α value) setting range : 1 ~ 600 seconds

e. Auto shutdown setting range: St-0~St-5 (None and 0.5~5Hours)

a. Max. pressure value : 2.5kg/cm²

b. Min. pressure value : 1.5kg/cm²

c. Delay Time when reaching the Max. Pressure : 15seconds

d. The pressure unit : kg/cm²

e. Detection time of water shortage : 30 seconds

f. Pressure of water shortage : 0.5kg/cm²

g. Time of automatic re-start running after warning shutdown

(α value) : 60 seconds

h. Auto shutdown setting after continuous running : St-0

i. Over pressure value is fixed in 10bar and cannot modify

9.The actual operating parameters display

1).Max. pressure setting display (high pressure) (Show code P-max)

2).Min. start pressure setting display (low pressure) (Show code P-min)

↓ Press once

a. Press once to browse original pressure value

↓ Press once

- -

dF-n

dF-y

- -

- - - -

loAd

Restore to

default value

setting

LCD screen

display “loAd”

or “ ----” for 3

seconds to

store and finish

the setting

a.Select to restore default value settings

(dF-y), press the right button and adjust the

parameter value from dF-n to dF-y.

After finishing the setting, press the SET

button, then all the advanced value

settings are returned to default value.

LCD screen display "- - - -" for 3 seconds

and back to the actual pressure conditions.

b.Stay on this screen for 30 seconds, the

display screen will back to the actual

pressure conditions automatically and the

preset data value is not stored.

c.Choose not to return to default value

settings (dF-n), select dF-n and press the

SET button again, LCD screen display

"loAd" for 3 seconds and will back to the

After LCD screen display “loAd” or “ ----” for

3 seconds later, above setting value are

stored and go to the actual pressure value

automatically.

Item

Parameters

Display

Code

Default

Unit

Data

Range

Description

actual pressure conditions automatically.

1).Max. pressure setting (high pressure) (Show code P-max)

3).Pressure of water shortage setting display (Dry running)

(Show code P-Dry)

4).Actual pressure status display

↓ Press again

b. Press once to enter basic setting

Press

to adjust the value upward

Press

to adjust the value downward

2).Min. Start pressure setting (low pressure) (Show code P-min)

↓ Press once

Press

to adjust the value upward

Press

to adjust the value downward

↓ Press once

1).Change the display working pressure unit (Show code Unit)

3).Time-Delay setting after reaching the Max. Pressure(Show code

Delay)

4).All parameter settings is stored (Show code loAd)

c. Press for 3 seconds to enter advanced setting

Press

to adjust the value upward

Press

to adjust the value downward

↓Press once

↓3 seconds later

5).After finishing above setting, 3 seconds later will go to the actual

pressure status display automatically.

Press to set up unit

Cycle of working pressure unit:

kg/cm² → psi → bar → kg/cm²

↓Press once

2).Detection time setting of water shortage (Show code P-Dry & sec)

3).Pressure of water shortage setting (Show code P-Dry) 5). Auto shutdown setting after continuous running (Show code Auto)

Press

to adjust the value upward

Press

to adjust the value downward

↓ Press once

4).Time setting of automatic re-start running after warning shutdown

(Dry running or Over pressure) (α value) (Show code Auto reset)

Press

to adjust the value upward

Press

to adjust the value downward

↓ Press once

Press

to adjust the value upward

Press

to adjust the value downward

↓ Press once

St-0: Pressure controller keeps running and won’t shut down

automatically.

St-.5&St-1~5: Pressure controller will auto shut down after

continuously running 0.5 or 1~5 hours and won’t auto restart

after the shutdown.

Press

to adjust the value upward

Press

to adjust the value downward

↓ Press once

6).Restore to default value setting or not

Restore to default value settings (show code dF-y)

Press to adjust the value to dF-y

Press once and restore to default value (Show code ----)

7).After ﬁnishing above settings, LCD screen display “loAd” or “ ----”

3 seconds later, go to the actual pressure status display automati-

cally .

Not restore to default value settings (show code dF-n)

Press to set the value to dF-n

Press once then all settings are stored. (Show code loAd)

Pressure controller display “EEEE”

It means the failure of pressure

sensor.

Pressure controller display “FFFF”

It means the failure of temperature

sensor.

Pressure controller display “EEFF”

It means the failure of pressure and

temperature sensor.

b).FFFF

c).EEFF

a).EEEE

10.Fault Display

Autres manuels pour DPC-10

Table des matières

Autres manuels Evak Contrôleurs

Evak

Evak DPC-10 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur