ETL PANSAT 330A Manuel utilisateur
FCC ID:PZ8PANSAT330A
Report No: E01.1105.FCC.451N
Test Date: February 18~21, 2002
Appendix F. User’s Manual
ETL Inc.
371-51 Gasan-Dong,
Geumcheon-Gu, Seoul,
153-023, Korea
1of 1
Hyundai Digital Technology Co., Ltd
.
Digital Satellite Receiver
Model :PANSAT 330A
1
1. Introduction 2
1.1. Overview
1.2. Main Features
2. Safety/Precautions 3
2.1. Safety
2.2. Precautions
3. Check Point before Use 5
3.1. Accessories
3.2. The Satellite dish
4. Controls/Functions 6
4.1. Front Panel
4.2. Rear Panel
4.3. Remote Controller
5. Using Remote Controller 12
5.1. Batteries
5.2. Range Of Operation
6. How to Connect 14
7. Operation 16
7.1. Getting Started
7.2. Channel Editing
7.3. System Parameters
7.4. Transponder
7.5. Factory Set
7.6. Other Function on Remote Control
8. Trouble Shooting 65
9. Specifications 66
DiSEqC is a trademark of EUTELSAT.
2
This satellite receiver is designed for using digital free-to-air channel reception. Enjoy
the rich choice of more than 4,000 different channels, broadcasting a large range of
culture, sports, cinema, news, events, etc. This receiver is a technical masterpiece,
assembled with the highest qualified electronic parts.
Fully compliant with MPEG-2 and DVB standards
User friendly operating Menu and On-Screen Graphic Menu
Easy to use EPG(Electronic Program Guide) on screen
Age protection lock function
Tele-text encoding
Manual PID control
Software downloading via RS-232C connector
DiSEqC 1.2 compatible
3
Be sure to read the user's manual
before starting the operation of the
unit.
Never open the cover. It is very
dangerous to touch the inside of the
unit due to possible electric shock.
When you do not use this unit for a
long time, make sure that power
cord is pulled out from the outlet.
Also do not use a damaged power
cord as it may cause fire or electric
shock.
Do not touch the power cord with
wet hands as it may cause electric
shock.
A professional installation is
required.
If reception is interrupted, contact
your local service centre.
Place the unit in a well ventilated
and no-heat environment.
4
When installing the unit
Install the unit horizontally. An
uneven installation may cause the
unit to be damaged.
Do not put heavy items such as a TV
on the unit. That may cause the unit
to be damaged.
Moving the unit to a hot area from a
cold one will cause condensation.
Do not operate the unit for one or two
hours or until it has dried completely.
Where it is subject to vibrations
Where it is exposed to direct sunlight
Where there is humidity
Where the temperature is too high or
too low.
Where there is no ventilation
Do not install the unit:
5
User's manual : 1
User's manual
Remote control : 1
Batteries (AAA type) : 2
If any accessories listed above are
missing, contact the sales
representative where you
purchased this unit.
This unit is working with DiSEqC 1.2 on a compatible antenna positioner.
Ask your dealer for information.
Accessories of the Unit
QZ-
123
456
78
0
9
ABC DEF
GHI JKL MNO
PRS TUV WXY
INFO AUDIO
GUIDE CH.LIST
MENU EXIT
RECALL
TV/RADIO AUX IN TV/SAT
SLEEP
VOL
CH
VOL
CH
Your dish should be properly installed and azimuth and elevation must be precisely set up.
6
Power
To switch the receiver in “standby” mode or in power on mode.
Standby/Power on Indication light
Turn on red while in the “standby” mode and turn off the red light while in the
power on mode.
Remote Sensor
Receives the infrared signal from remote control.
Channel Display(4 Digit)
- When you connect the power line of the receiver, the current time is displayed.
- After programming, the program number is displayed.
Menu
To launch or terminate the menu application.
Select
To activate a highlighted item or go to next level on hypertext menu or confirm
the user s action.
7
- Vol. /
To adjust the volume level or change the value of an item with preprogrammed
values. The Key can be used as a backspace to cancel the numerical
input.
- CH. /
To change channel or cursor position on the application screen.
8
No. Name Connector Function
1. TV ANT IN IEC 169-2 female Input from terrestrial antenna.
2.
RF OUT UHF 3-4
IEC 169-2 male Output to TV.
3. AUDIO L RCA cinch Left audio output.
4. AUDIO R RCA cinch Right audio output.
5. VIDEO RCA cinch Composite video output.
6.
Digital Audio
RCA cinch Digital Audio Output
7. S-VHS Output to VCR or TV.
8. RS-232C DB-9 Low speed serial port.
9. LNB INPUT
IEC 169-24 female
IF input from LNB to digital tuner.
10. LOOP OUT
IEC 169-24 female
IF loop-through output from
digital tuner.
9
POWER :
To switch into ‘standby’ or ‘power on’
mode.
MUTE :
To turn the sound on/off.
Numeric Keys(0-9) :
To select channels and input of
channel numbers or characters.
INFO. :
To display the information of the
current channel.
AUDIO :
To change the audio track, stereo-
mono mode.
GUIDE :
(EPG : Electronic Program Guide)
To watch program information. Press
once more to return to normal mode.
CH LIST :
To watch the channel list.
Press to confirm or press EXIT to
return to previous chosen channel.
-Up & Down :
To change the value of a selected
item with preprogrammed values
in menu.
QZ-
123
456
78
0
9
ABC DEF
GHI JKL MNO
PRS TUV WXY
INFO AUDIO
GUIDE CH.LIST
MENU EXIT
RECALL
TV/RADIO AUX IN TV/SAT
SLEEP
VOL
CH
VOL
CH
Table des matières
