ETL 40829 Manuel utilisateur
Questions, problems or missing parts? Before returning this item to your retailer, call our customer service department
at 1-800-643-0067, Monday - Thursday, 8am - 6pm, Friday, 8am - 5pm EST.
ITEM #0845047
MODEL #40829
ST. KITTS CEILING FAN
2
PACKAGE CONTENTS HARDWARE CONTENTS
(not drawn to scale)
Mounting Bracket Screw (x 4)
Note: Some extra fasteners are included for your
convenience.
Blade Balancing Kit
Plug Button
Blade Washer (x 15)
Lock Washer (x 15)
Blade Screw (x 15)
Wire Connector (x 3)
Pull Chain Extension (x 2)
Switch Housing
Screw (x 3)
Bulb (x 2)
Mounting Bracket
Canopy
Canopy Cover
Downrod
Clip
Pin
Blade Arm (x 5)
Blade (x 5)
Yoke Cover
Yoke
Finial
Closemount
Screw (x 3)
Motor Assembly
Switch Housing
Switch
Housing
Cap
Light Kit
Glass Bowl
Finial Cap
3
TABLE OF CONTENTS
PREPARATION
Before beginning the assembly of this product, ensure all parts are present. Compare all parts with the package contents list and hardware contents
list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 120 minutes
Tools required for assembly (not included): Electrical tape, Phillips Screwdriver, Pliers, Safety Glasses, Step Ladder, and Wire Strippers
Helpful Tools (not included): AC Tester Light, Tape Measure, Wiring Handbook and Wire Cutters
Package Contents .....................................................................................................2
Preparation ..........................................................................................................3
Initial Installation ......................................................................................................5
Downrod or Angle Mounting .............................................................................................6
Closemount Instructions ................................................................................................8
Final Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installation Without Light Kit ............................................................................................13
Operating Instructions .................................................................................................14
Safety Information ....................................................................................................15
Care and Maintenance ................................................................................................15
Troubleshooting......................................................................................................16
Warranty ...........................................................................................................17
Replacement Parts List ................................................................................................18
4
PREPARATION
1. Turn o power.
Turn o the power to the fan at the breaker
box and the wall switch.
2. Choose mounting option.
Standard Mounting is best suited for
ceilings 8 ft. or higher. For very high ceilings,
use a longer downrod (not included).
Angle Mounting is best suited for angled
or vaulted ceilings. A longer downrod is
sometimes necessary to ensure proper
blade clearance. Ensure the ceiling angle is
not steeper than 16 degrees.
Flushmount installation is not available for
this item.
Closemount installation is best suited for
ceilings 8 ft. or lower.
3. Choose suitable location.
Ensure the blades will be at least 30 inch-
es from any obstructions. Also check the
downrod length to ensure the blades will be
at least 7 feet above the oor.
Failure to disconnect the power supply
prior to installation may result in serious
injury or death.
See page 15 for complete description of
cautions and warnings.
Downrod Mounting
Flushmount Closemount
Angle Mounting
5
INITIAL INSTALLATION
Standard and
Closemount
Mounting
Angle
Mounting
D
2. Install the mounting bracket.
Install the mounting bracket to the outlet
box (sold separately) using the screws and
washers provided with the outlet box.
1. Remove the mounting bracket.
Loosen all four mounting bracket screws
and completely remove the two screws from
the round holes in the canopy. Then, remove
the mounting bracket from the canopy.
Note: Save the mounting bracket screws for
later use.
3. Remove the motor blocks.
Remove the ten motor screws from the
underside of the motor. Keep the motor
screws for later, but discard the motor
blocks.
For downrod or angle mounting
instructions, proceed to the next page. For
CLOSEMOUNT INSTALLATION, skip to
page 8.
x 4 x 10
Motor Block
Motor Screw
Mounting
Bracket
Screw
6
1. Loosen set screws and remove
pin and clip.
Remove the clip and pin from the downrod.
Then partially loosen the two set screws in
the yoke at the top of the motor assembly.
2. Feed the wires through the yoke
cover, canopy, and downrod.
Insert the downrod through the yoke cover,
canopy, and downrod.
3. Install the downrod into the
yoke.
Slide the downrod into the yoke at the top
of the motor assembly. Align the holes, and
reinstall the pin and clip. Then tighten both
set screws.
DOWNROD OR ANGLE MOUNTING
Clip
Clip
Pin
Pin
Set Screw
Set Screw
Downrod
Canopy
Yoke Cover
Yoke
7
Tab
Slot
4. Trim fan wires.
Depending on the length of downrod you
use, you may want to cut the fan wires to
simplify wiring. After pulling the wires all the
way through the downrod, measure 8 inches
of wire. Cut o the excess wire using wire
cutters (not included).
5. Strip 1/2” of wire insulation.
Strip 1/2 inch of insulation from the end of
each wire. Twist the stripped ends of each
wire strand.
Note: If you didn’t trim the wires in the
previous step, this step is not necessary.
6. Hang downrod in mounting
bracket.
Install the ball end of the downrod into the
opening of the mounting bracket. Align the
slot in the ball with the tab on the mounting
bracket.
Proceed to FINAL INSTALLATION, page 9.
DOWNROD OR ANGLE MOUNTING
Failure to align the slot in the ball with the
tab on the mounting bracket may cause
the fan to fall, which could result in injury
or death.
8 in.
8
1. Remove canopy cover from
bottom of canopy.
The canopy cover snaps out of the hole in
the bottom of the canopy.
2. Install canopy to top of motor
assembly.
Remove the three Phillips head closemount
screws from the top of the motor assembly.
Then, align the canopy with the holes in the
top of the motor assembly. The larger holes
in the canopy will encompass the remaining
screws. Secure the canopy to the top of
the motor assembly with the closemount
screws.
3. Hang canopy on mounting
bracket.
Raise the motor assembly and place the
canopy on the mounting bracket hook to
temporarily hold the fan during the wiring
process.
CLOSEMOUNT INSTALLATION (optional)
x 3
Canopy Cover
Canopy
Closemount Screw
Mounting Bracket
Hook
Canopy
9
1. Wire the fan.
Connect household supply and fan wires
according to the diagram and these steps:
• Connect the Green wire from the downrod
and mounting bracket to the Bare/Green
supply wire. Note: Closemount installation
does not use downrod, so there will only be
two Green wires to connect.
• Connect the White wire from the fan to the
White supply wire.
• Connect the Black and Blue wires from the
fan to the Black supply wire.
• Secure all wiring connections together with
wire connectors.
2. Attach the canopy to the
mounting bracket.
Align the canopy over the loosened
mounting bracket scews preassembled to
the mounting bracket. Place the L-slot of the
canopy onto the mounting bracket screws
and rotate counterclockwise.
3. Re-install the mounting bracket
screws.
Re-install the two previously removed
mounting bracket screws into the round
holes of the canopy.
FINAL INSTALLATION
x 3 x 4 x 4
Mounting
Bracket
Screw
Mounting
Bracket
Screw
Canopy
Black (Hot)
Wire Connector
White (Neutral)
Bare/Green (Ground)
Black
Blue
White
Green
Note: If there is a second hot supply wire
coming from the outlet box, connect it to the
blue (light power) fan wire for separate light
and fan control.
10
4. Attach the blades to blade arms.
Partially insert blade screw along with lock
washer and blade washer through one blade
and into one blade arm. Tighten each blade
screw, starting with the one in the middle.
Repeat this step for the remaining blades
and blade arms.
5. Attach blade arms to motor.
Install the blade arm to the underside of
the motor assembly with the ten previously
removed motor screws.
6. Connect light kit wires.
Remove the three switch housing screws
from the switch housing cap. Then, connect
the single-pin wire connectors from the fan
to the light kit -- blue to black and white to
white. Ensure the connectors are secure.
Then attach the switch housing cap to the
switch housing using the switch housing
screws.
FINAL INSTALLATION
x 3 x 3
Blade Washer Lock Washer
Blade Arm
Blade Screw
Single-pin
Connector
Blade Arm
Motor Screw
Switch
Housing
Screw
Switch
Housing
Cap
Table des matières
