eTIGER S3b Sim Secual Manuel de l'opérateur
www.etiger.com
S3b Sim Secual / S3b Sim Vid Secual
GSM Alarm System
EN
Features
-GSM frequency: 850 / 900 / 1800 / 1900 MHz
- Supports up to 10 remote controls, 50 wireless accessories and 50 RFID tags
- Can store up to 5 phone numbers, 5 SMS numbers
-Radio-frequency security of the accessories: more than one million code combinations
- Arm / disarm the system by SMS, phone call, or App (on iOS or Android)
- Can be disarmed by RFID tag
- Built-in siren (100dB) and call function from the panel
- SMS alerts for power failure, power recovery and low battery
- Audio surveillance of the site from distance
-2 x 800 mAh lithium batteries included (8h battery life in standby mode)
Specications
Product name
S3b Sim Secual
SKU
S3b-S
Control panel power supply
Input: AC 110-240V / 50-60 Hz
Output: DC 12V / 800 mA
GSM operating frequency
850 / 900 / 1800 / 1900 mHz
Radio-frequency
433 MHz (±75 KHz)
Standby current
110 mA
Alarm current
340 mA
Backup batteries
Lithium batteries: 3.7 V / 800 mAh x 2 (BL-5B)
Internal siren
100 dB
Housing material
ABS plastic
Operating conditions
Temperature: -10°C~55°C
Humidity: ≤ 80% (non-condensing)
Control panel dimensions (L x W x H)
188 x 132 x 26 mm
Box Content
S3b Control Panel x1
Motion Detectors x2
Door / Window Contacts x2
Remote Controls x2
RFID Tags x2
AC Adaptor x1
Documentation x1
S3b Sim Vid Secual
+ IP Camera x 1 (with AC Adaptor and manual)
Quick Start-up
Accessories Safety and Troubleshooting
4
Quick start-up Control Panel Operations SMS Operations
Control Panel Layout (Front)
GSM Signal Indicator
Searching GSM network: Blinks once every second
GSM signal is normal: Blinks once every two seconds
Touch Keypad
Status Indicator
Record Voice Memo /
Connecon Buon
Stay Arm (Home Mode)
RFID player /
Play Voice Memo
Call
Arm
Disarm
Control Panel Layout (Back)
LoudspeakerMIC
Baery compartment
Tamper switch
SIM card Slot Power
On/O
Output for
wired sensors
Wired sensors
(24h zone)
Adapter interface
Electronic lock
Wired siren 500mA
Wired sensors
(Normal zone)
Accessories Safety and Troubleshooting
5
Quick start-up Control Panel Operations SMS Operations
Connect your System
Open the battery case at the back of the control panel and insert a SIM card in the control
panel.
Important
Before using the S3b Sim Secual, you need to purchase a SIM card that works on the GSM
network with 850 / 900 / 1800 / 1900 MHz frequency. We recommend you to subscribe to a
plan with unlimited texts and one hour of voice. For more information, please contact your
local reseller.
Important
Make sure the SIM card does not require any PIN code. For more information, please contact
your local reseller.
Turn your System On
1. Plug the AC adaptor to an AC socket.
2. Plug the output connector of the AC adaptor into the
adaptor interface in the battery compartment at the
back of the control panel.
3. Turn the power switch to "ON" (in the battery
compartment at the back of the control panel).
Mount the Control Panel
Before mounting the control panel on the wall, make sure the reception of the GSM signal is
sucient.
Fix the wall-mounting bracket on the wall with screws. Wedge the panel on the bracket, make
sure they t well.
Accessories Safety and Troubleshooting
6
Quick start-up Control Panel Operations SMS Operations
First Operations
Store a phone number
To interact with the control panel by SMS, by phone call and/or from the app, at least one phone
number for SMS notications must be stored in the control panel. Please refer to the instructions
page 13 of this manual.
Change the language
By default the language of the S3b control panel is set to English. If you wish to change the
system language, refer to the instructions page 18 of this manual. "System language" refers
to the language of the SMS you receive from the control panel.
Arm / Disarm the System
The alarm system can be armed or disarmed on the control panel, by SMS, by App and by phone
call.
On the control panel: Refer to the instructions on page 9 of this manual.
By SMS
To arm the system: Send “1”by SMS to the number of your system’s SIM card.
To disarm the system: Send “0”by SMS to the number of your system’s SIM card.
By RFID tag (disarm only): Swipe the RFID tag in front of the RFID reader of the control panel.
To start receiving SMS notications when the system is disarmed by RFID tag, you must store an
SMS number as explained on page 13 of this manual. If you have stored several SMS numbers,
only the rst number stored will receive SMS notications when the system is disarmed by RFID tag.
By app
In the app, click on“Arm”or“Disarm”to respectively arm or disarm the system.
The app is available for download on the App Store and Google Play (more information on etiger.com).
Register Wireless Accessories & RFID Tags
1. Type your password followed by the Connection button " " on the control panel to enter the
Connection Mode.
2. Trigger the accessory once within the next 15 seconds (for the RFID tag, swipe it in front of the
blue circle of the control panel). You hear one beep: the registration is successful.
Default password is 1234. To change the password, refer to instructions on page 18.
If the accessory has already been registered, the control panel will beep twice.The rst accessory
registered is assigned to zone 1, the second accessory registered is assigned to zone 2, etc. Zones
1 to 9 can be renamed. Zones 10 to 50 cannot be renamed (refer to the instructions on page 15
to learn how to rename zones).
Accessories Safety and Troubleshooting
7
Quick start-up Control Panel Operations SMS Operations
Speed Dial
This function is only available when the system is disarmed.
Press the Call button“ ”on the control panel for 3 seconds: the panel auto-dials the rst stored
phone number. Press the Call button“ ” to end the call.
Hands-Free Phone Call from the Panel
This function is only available when the system is disarmed.
Type the phone number you wish to call and press the Call button“”.
Record / Play a Voice Memo
Long press the RecordVoice Memo button { } to record a 10-second voice message.The PlayVoice
Memo Button blinks when a message has been recorded.
Touch the centrer of the circle on the control panel to listen to the voice memo. The LED in-
dicator turns o when the voice memo is being played. Touch it again to replay the memo.
Hard Reset
Turn the control panel on (if the control panel is already on, turn it o and turn it on again).
Press the tamper switch at the back of the control panel 5 times within 5 seconds after having
turned it on.
Settings will be restored to default values. Stored phone numbers and connected accessories
will be cleared.
Control Panel Operations
Accessories Safety and Troubleshooting
9
Quick start-up Control Panel Operations SMS Operations
Arm the System
Press the Arm button " " on the control panel. The control panel beeps once: the system is
armed.
Note
If the Entry / Exit Delay is activated, only the Delay zone will be armed after the delay set (refer
to instructions on page 17 of this manual “Entry / Exit Delay”).
Disarm the System
Type your password and press the Disarm button " " on the control panel. The control panel
beeps twice: the system is disarmed.
Home Mode
Press the Stay button " " on the control panel. The control panel beeps twice: the system is
armed in Home Mode.
In Home Mode, all the sensors are armed except those assigned to the Home zone. Sensors
assigned to the Home Mode zone are disarmed: they cannot trigger an alarm.
For more information on zone setup, please refer to the instructions on page 29 of this
manual.
Accessories Safety and Troubleshooting
10
Quick start-up Control Panel Operations SMS Operations
Control by Phone Call
Method 1
When an alarm has been triggered, the control panel dials the pre-stored phone numbers.
When you take the call, you can control the panel from distance according to the instructions
in the table below.
Method 2
1. Dial the telephone number of the SIM card in your control panel.
2. Enter your password followed by ”#”. *
3. Select the operations to control the panel (see instructions in the table below).
Note
The call will end automatically if you do not send any command within 30 seconds.
*Default password is 1234.
Table of commands for control by phone call
Command Function Comment
Press“1“ Arms the system -
Press“0“
- Disarms the system and turns the siren o
- Stops monitoring without hanging up
- Ends the phone call without hanging up
-
Press“ “Audio monitoring -
Press“3“ Phone call with control panel -
Press“6“ Turns the siren o -
Press“9“ Turns the siren on -
Press“#“ - Disarms the system and turns the siren o
- Exits control by phone call
Hanging up also exits the
control by phone call.
Autres manuels pour S3b Sim Secual
4
Ce manuel convient aux modèles suivants
1
Table des matières
Langues :
Autres manuels eTIGER Système de sécurité
eTIGER
eTIGER S3b Sim Secual Manuel de l'opérateur
eTIGER
eTIGER S3b Manuel utilisateur
eTIGER
eTIGER S4 Cell + Line Manuel utilisateur
eTIGER
eTIGER S4 Combo Secual Manuel utilisateur
eTIGER
eTIGER S5 Manuel utilisateur
eTIGER
eTIGER S2 Manuel utilisateur
eTIGER
eTIGER S4 Combo Secual Manuel utilisateur
eTIGER
eTIGER ES-D3A Manuel utilisateur
eTIGER
eTIGER S3b Sim Secual Manuel utilisateur
eTIGER
eTIGER ES-D3B Manuel utilisateur
eTIGER
eTIGER secual box Manuel utilisateur
eTIGER
eTIGER ES-D4A Manuel utilisateur
eTIGER
eTIGER Secual Box V2 Manuel utilisateur
eTIGER
eTIGER S4 Combo Secual Manuel utilisateur
eTIGER
eTIGER ES-S6A Manuel utilisateur
eTIGER
eTIGER S3 Sim Secual Manuel utilisateur
eTIGER
eTIGER ES-S7A Manuel utilisateur
eTIGER
eTIGER S3b Sim Secual Manuel utilisateur
eTIGER
eTIGER S3b Sim Secual Manuel utilisateur
eTIGER
eTIGER ESB-WS2A Manuel utilisateur
Manuels Système de sécurité populaires d'autres marques
EDM
EDM Solution 6+6 Wireless-AE Manuel utilisateur
Highway Safety Group
Highway Safety Group EA401 Manuel utilisateur
Siren
Siren LED GSM Manuel utilisateur
Detection Systems
Detection Systems 7090i Instructions de montage
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuel utilisateur
Siemens
Siemens FDM273 Manuel utilisateur