Etatron EOne MF 0110 Manuel utilisateur

Part B: Attaching suction & foot lter tubing

Cut clear tubing

in two pieces that

are the correct

size for your

application.

Attach one of the

two clear PVC

tubes to the

suction valve

following steps

2 - 5 in part A.

Attach the foot

filter (using

same process as

above), to other

end of clear PVC

tubing. Place into

the stock tank.

Slide the second

clear PVC tube

onto the priming

barb, and place

into the

stock tank.

eOne MF 0110 Quick Start Guide

• eOne MF pump

• Bracket Mounting Kit

• Operating instructions

and maintenance manual

• Allen Wrench (to remove solenoid

head when needed)

• Hose Packet

- Opaque, Rigid PE Tubing for

the Discharge

- Clear, Flexible, PVC Suction Tube

- Injection Valve

- Foot Filter

NOTE: Remove safety labels before installing

and remember pumps may hold water inside.

Part A: Attaching the opaque tubing to

the injection valves

Remove the

top discharge

valve nut.

Remove the

protective cap

from the nut and

discard.

Insert the opaque

tubing through

the nut. Slide the

locking collar

and insert the

hose nozzle

over the tube

creating a

compression

fitting.

Screw the nut

back onto the

discharge valve.

Hand tighten.

Attach other end

of tubing to the

injection stem,

follow steps 3 and

4. Install injection

stem into the

water line.

Flow Rate 0.26 GPH, Max. Pressure 145 PSI

Part C: Connecting the Water Meter

Tools needed: punch, small and standard

size at head screwdriver

Remove bottom

front cover using a

standard flat head

screw driver.

Remove the

rubber cap on

the left.

Using a punch

tool, punch a small

hole through the

rubber cap.

Insert the Water

Meter wires

through the hole in

the cap.

Run the wires

back through the

hole in the front

cover. Reinsert

the rubber cap.

Insert wires on

3rd and 4th holes

from left. Push

button and insert

wires using small

screwdriver.

Make sure they

are connected

properly.

Included in the Box

Discharge

Valve

Priming

Barb

Suction

Valve

Air Bleed

Valve

Injection stem has

1/2”, 3/8” and M10

MPT thread options.

Cut to your

specifications.

Insert into water line

so that the end of

injection valve is

midway in the pipe.

(Continue to back)

DO NOT CUT

passed this point

Part B: Attaching suction & foot lter tubing

Cut clear tubing

in two pieces that

are the correct

size for your

application.

Attach one of the

two clear PVC

tubes to the

suction valve

following steps

2 - 5 in part A.

Attach the foot

filter (using

same process as

above), to other

end of clear PVC

tubing. Place into

the stock tank.

Slide the second

clear PVC tube

onto the priming

barb, and place

into the

stock tank.

eOne MF 0110 Quick Start Guide

• eOne MF pump

• Bracket Mounting Kit

• Operating instructions

and maintenance manual

• Allen Wrench (to remove solenoid

head when needed)

• Hose Packet

- Opaque, Rigid PE Tubing for

the Discharge

- Clear, Flexible, PVC Suction Tube

- Injection Valve

- Foot Filter

NOTE: Remove safety labels before installing

and remember pumps may hold water inside.

Part A: Attaching the opaque tubing to

the injection valves

Remove the

top discharge

valve nut.

Remove the

protective cap

from the nut and

discard.

Insert the opaque

tubing through

the nut. Slide the

locking collar

and insert the

hose nozzle

over the tube

creating a

compression

fitting.

Screw the nut

back onto the

discharge valve.

Hand tighten.

Attach other end

of tubing to the

injection stem,

follow steps 3 and

4. Install injection

stem into the

water line.

Flow Rate 0.26 GPH, Max. Pressure 145 PSI

Part C: Connecting the Water Meter

Tools needed: punch, small and standard

size at head screwdriver

Remove bottom

front cover using a

standard flat head

screw driver.

Remove the

rubber cap on

the left.

Using a punch

tool, punch a small

hole through the

rubber cap.

Insert the Water

Meter wires

through the hole in

the cap.

Run the wires

back through the

hole in the front

cover. Reinsert

the rubber cap.

Insert wires on

3rd and 4th holes

from left. Push

button and insert

wires using small

screwdriver.

Make sure they

are connected

properly.

Included in the Box

Discharge

Valve

Priming

Barb

Suction

Valve

Air Bleed

Valve

Injection stem has

1/2”, 3/8” and M10

MPT thread options.

Cut to your

specifications.

Insert into water line

so that the end of

injection valve is

midway in the pipe.

(Continue to back)

DO NOT CUT

passed this point

Part B: Attaching suction & foot lter tubing

Cut clear tubing

in two pieces that

are the correct

size for your

application.

Attach one of the

two clear PVC

tubes to the

suction valve

following steps

2 - 5 in part A.

Attach the foot

filter (using

same process as

above), to other

end of clear PVC

tubing. Place into

the stock tank.

Slide the second

clear PVC tube

onto the priming

barb, and place

into the

stock tank.

eOne MF 0110 Quick Start Guide

• eOne MF pump

• Bracket Mounting Kit

• Operating instructions

and maintenance manual

• Allen Wrench (to remove solenoid

head when needed)

• Hose Packet

- Opaque, Rigid PE Tubing for

the Discharge

- Clear, Flexible, PVC Suction Tube

- Injection Valve

- Foot Filter

NOTE: Remove safety labels before installing

and remember pumps may hold water inside.

Part A: Attaching the opaque tubing to

the injection valves

Remove the

top discharge

valve nut.

Remove the

protective cap

from the nut and

discard.

Insert the opaque

tubing through

the nut. Slide the

locking collar

and insert the

hose nozzle

over the tube

creating a

compression

fitting.

Screw the nut

back onto the

discharge valve.

Hand tighten.

Attach other end

of tubing to the

injection stem,

follow steps 3 and

4. Install injection

stem into the

water line.

Flow Rate 0.26 GPH, Max. Pressure 145 PSI

Part C: Connecting the Water Meter

Tools needed: punch, small and standard

size at head screwdriver

Remove bottom

front cover using a

standard flat head

screw driver.

Remove the

rubber cap on

the left.

Using a punch

tool, punch a small

hole through the

rubber cap.

Insert the Water

Meter wires

through the hole in

the cap.

Run the wires

back through the

hole in the front

cover. Reinsert

the rubber cap.

Insert wires on

3rd and 4th holes

from left. Push

button and insert

wires using small

screwdriver.

Make sure they

are connected

properly.

Included in the Box

Discharge

Valve

Priming

Barb

Suction

Valve

Air Bleed

Valve

Injection stem has

1/2”, 3/8” and M10

MPT thread options.

Cut to your

specifications.

Insert into water line

so that the end of

injection valve is

midway in the pipe.

(Continue to back)

DO NOT CUT

passed this point

Part B: Attaching suction & foot lter tubing

Cut clear tubing

in two pieces that

are the correct

size for your

application.

Attach one of the

two clear PVC

tubes to the

suction valve

following steps

2 - 5 in part A.

Attach the foot

filter (using

same process as

above), to other

end of clear PVC

tubing. Place into

the stock tank.

Slide the second

clear PVC tube

onto the priming

barb, and place

into the

stock tank.

eOne MF 0110 Quick Start Guide

• eOne MF pump

• Bracket Mounting Kit

• Operating instructions

and maintenance manual

• Allen Wrench (to remove solenoid

head when needed)

• Hose Packet

- Opaque, Rigid PE Tubing for

the Discharge

- Clear, Flexible, PVC Suction Tube

- Injection Valve

- Foot Filter

NOTE: Remove safety labels before installing

and remember pumps may hold water inside.

Part A: Attaching the opaque tubing to

the injection valves

Remove the

top discharge

valve nut.

Remove the

protective cap

from the nut and

discard.

Insert the opaque

tubing through

the nut. Slide the

locking collar

and insert the

hose nozzle

over the tube

creating a

compression

fitting.

Screw the nut

back onto the

discharge valve.

Hand tighten.

Attach other end

of tubing to the

injection stem,

follow steps 3 and

4. Install injection

stem into the

water line.

Flow Rate 0.26 GPH, Max. Pressure 145 PSI

Part C: Connecting the Water Meter

Tools needed: punch, small and standard

size at head screwdriver

Remove bottom

front cover using a

standard flat head

screw driver.

Remove the

rubber cap on

the left.

Using a punch

tool, punch a small

hole through the

rubber cap.

Insert the Water

Meter wires

through the hole in

the cap.

Run the wires

back through the

hole in the front

cover. Reinsert

the rubber cap.

Insert wires on

3rd and 4th holes

from left. Push

button and insert

wires using small

screwdriver.

Make sure they

are connected

properly.

Included in the Box

Discharge

Valve

Priming

Barb

Suction

Valve

Air Bleed

Valve

Injection stem has

1/2”, 3/8” and M10

MPT thread options.

Cut to your

specifications.

Insert into water line

so that the end of

injection valve is

midway in the pipe.

(Continue to back)

DO NOT CUT

passed this point

Part B: Attaching suction & foot lter tubing

Cut clear tubing

in two pieces that

are the correct

size for your

application.

Attach one of the

two clear PVC

tubes to the

suction valve

following steps

2 - 5 in part A.

Attach the foot

filter (using

same process as

above), to other

end of clear PVC

tubing. Place into

the stock tank.

Slide the second

clear PVC tube

onto the priming

barb, and place

into the

stock tank.

eOne MF 0110 Quick Start Guide

• eOne MF pump

• Bracket Mounting Kit

• Operating instructions

and maintenance manual

• Allen Wrench (to remove solenoid

head when needed)

• Hose Packet

- Opaque, Rigid PE Tubing for

the Discharge

- Clear, Flexible, PVC Suction Tube

- Injection Valve

- Foot Filter

NOTE: Remove safety labels before installing

and remember pumps may hold water inside.

Part A: Attaching the opaque tubing to

the injection valves

Remove the

top discharge

valve nut.

Remove the

protective cap

from the nut and

discard.

Insert the opaque

tubing through

the nut. Slide the

locking collar

and insert the

hose nozzle

over the tube

creating a

compression

fitting.

Screw the nut

back onto the

discharge valve.

Hand tighten.

Attach other end

of tubing to the

injection stem,

follow steps 3 and

4. Install injection

stem into the

water line.

Flow Rate 0.26 GPH, Max. Pressure 145 PSI

Part C: Connecting the Water Meter

Tools needed: punch, small and standard

size at head screwdriver

Remove bottom

front cover using a

standard flat head

screw driver.

Remove the

rubber cap on

the left.

Using a punch

tool, punch a small

hole through the

rubber cap.

Insert the Water

Meter wires

through the hole in

the cap.

Run the wires

back through the

hole in the front

cover. Reinsert

the rubber cap.

Insert wires on

3rd and 4th holes

from left. Push

button and insert

wires using small

screwdriver.

Make sure they

are connected

properly.

Included in the Box

Discharge

Valve

Priming

Barb

Suction

Valve

Air Bleed

Valve

Injection stem has

1/2”, 3/8” and M10

MPT thread options.

Cut to your

specifications.

Insert into water line

so that the end of

injection valve is

midway in the pipe.

(Continue to back)

DO NOT CUT

passed this point

Arrow right to

input number

of pulses.

Example image

shows 15 Pulse/

Strokes has

been entered.

Arrow down.

Click START.

Screen changes

reflecting what

you programmed:

1xNM 15 will

display in upper

left corner.

NOTE: Your pump will run upon

receiving a pulse from the Water

Meter. On the second signal the

pump will dose slower, spacing out

the pulses over time.

NEED HELP?

CALL 1-800-451-6628

Part D: Priming the pump

Plug the pump,

this will put you in

SET UP mode.

Press the arrow to

the right twice and

select MF.

Click START

button twice.

Screen shows

Operating Mode/

Manual Mode.

Pump will begin to

prime.

Part E: Programing the pump 1xN(M)

MODE

Press the right

arrow twice,

display will read

1XN(M). This

means pump

will stroke N

times with every

impulse from the

Water Meter with

memory function.

N = Number

of pulses

Arrow down once

and you have the

option to input

the PULSES

NUM:

eOne Installation

The pump is ready to receive signals from the Water Meter.

Priming Instructions

Water Meter Options

WM34-1PPG One pulse/gallon

WM34-10PPG One pulse/10 gallons

See operating manual for

complete instructions

and safety standards.

When connecting a metering

pump either to a public

water supply or to its own

water source, you must

respect the regulations in

force concerning protection

of the source i.e.

backflow prevention, etc.

!CAUTION

NOTE: Installation illustrations are to be

used as a reference guide only.

Arrow right to

input number

of pulses.

Example image

shows 15 Pulse/

Strokes has

been entered.

Arrow down.

Click START.

Screen changes

reflecting what

you programmed:

1xNM 15 will

display in upper

left corner.

NOTE: Your pump will run upon

receiving a pulse from the Water

Meter. On the second signal the

pump will dose slower, spacing out

the pulses over time.

NEED HELP?

CALL 1-800-451-6628

Part D: Priming the pump

Plug the pump,

this will put you in

SET UP mode.

Press the arrow to

the right twice and

select MF.

Click START

button twice.

Screen shows

Operating Mode/

Manual Mode.

Pump will begin to

prime.

Part E: Programing the pump 1xN(M)

MODE

Press the right

arrow twice,

display will read

1XN(M). This

means pump

will stroke N

times with every

impulse from the

Water Meter with

memory function.

N = Number

of pulses

Arrow down once

and you have the

option to input

the PULSES

NUM:

eOne Installation

The pump is ready to receive signals from the Water Meter.

Priming Instructions

Water Meter Options

WM34-1PPG One pulse/gallon

WM34-10PPG One pulse/10 gallons

See operating manual for

complete instructions

and safety standards.

When connecting a metering

pump either to a public

water supply or to its own

water source, you must

respect the regulations in

force concerning protection

of the source i.e.

backflow prevention, etc.

!CAUTION

NOTE: Installation illustrations are to be

used as a reference guide only.

Arrow right to

input number

of pulses.

Example image

shows 15 Pulse/

Strokes has

been entered.

Arrow down.

Click START.

Screen changes

reflecting what

you programmed:

1xNM 15 will

display in upper

left corner.

NOTE: Your pump will run upon

receiving a pulse from the Water

Meter. On the second signal the

pump will dose slower, spacing out

the pulses over time.

NEED HELP?

CALL 1-800-451-6628

Part D: Priming the pump

Plug the pump,

this will put you in

SET UP mode.

Press the arrow to

the right twice and

select MF.

Click START

button twice.

Screen shows

Operating Mode/

Manual Mode.

Pump will begin to

prime.

Part E: Programing the pump 1xN(M)

MODE

Press the right

arrow twice,

display will read

1XN(M). This

means pump

will stroke N

times with every

impulse from the

Water Meter with

memory function.

N = Number

of pulses

Arrow down once

and you have the

option to input

the PULSES

NUM:

eOne Installation

The pump is ready to receive signals from the Water Meter.

Priming Instructions

Water Meter Options

WM34-1PPG One pulse/gallon

WM34-10PPG One pulse/10 gallons

See operating manual for

complete instructions

and safety standards.

When connecting a metering

pump either to a public

water supply or to its own

water source, you must

respect the regulations in

force concerning protection

of the source i.e.

backflow prevention, etc.

!CAUTION

NOTE: Installation illustrations are to be

used as a reference guide only.

Table des matières

Autres manuels Etatron Pompe à eau

Etatron

Etatron DLXB pH-RX-CL Series Instructions d'utilisation

Etatron

Etatron DLX Instructions d'utilisation

Etatron

Etatron HD-MA Instructions d'utilisation

Etatron

Etatron BT Series Instructions d'utilisation

Etatron

Etatron DLX-MA/AD series Instructions d'utilisation

Etatron

Etatron eOne Manuel utilisateur

Etatron

Etatron eOneMa Manuel utilisateur

Etatron

Etatron DLX-pH/M SERIES Instructions d'utilisation

Etatron

Etatron eOne PLUS Instructions d'utilisation

Etatron

Etatron eOne MF Series Instructions d'utilisation

Etatron

Etatron DLX-MF/M Instructions d'utilisation

Etatron

Etatron BT MA/M Instructions d'utilisation

Etatron

Etatron BH3-V Instructions d'utilisation

Etatron

Etatron eSelect M 1 CI Instructions d'utilisation

Manuels Pompe à eau populaires d'autres marques

Neptun

Neptun NPHW 5500 Manuel utilisateur

Sensidyne

Sensidyne Gilian BDX-II Instructions d'installation et d'utilisation

Draper

Draper 47808 Manuel utilisateur

Trolla

Trolla 12820 Manuel utilisateur

Sunfab

Sunfab SVH Series Manuel utilisateur

WilTec

WilTec 50740 Manuel utilisateur

Fieldmann

Fieldmann FVC 5015 EK Manuel utilisateur

Everbilt

Everbilt EFSUB5-122HD Manuel utilisateur

Graco

Graco Husky 3300e Manuel utilisateur

esotec

esotec 101018 Manuel utilisateur

moyno

moyno 2000 CC Manuel utilisateur

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuel utilisateur

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guide de dépannage

DUROMAX

DUROMAX XP WX Series Manuel utilisateur

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuel utilisateur

Franklin Electric

Franklin Electric IPS Manuel utilisateur

Xylem

Xylem e-1532 Series Manuel utilisateur

Milton Roy

Milton Roy PRIMEROYAL Manuel utilisateur

Etatron eOne MF 0110 Manuel utilisateur

Manuels Pompe à eau populaires d'autres marques