Eswood ES50 Manuel utilisateur

EQUIPMENT MANUAL

FOR

ES50 HIGH PERFORMANCE

PASS THROUGH DISHWASHER

JUNE 2011

ESWOOD OPERATING MANUAL ES-50 June 2011

ABLE OF CONTENTS

1. Important: Prior to Installation 3

2. General Description 4-5

3. Technical Specifications 6

4. Installation 7

5. Initial Start- p Proced re 8

6. Washing Operation 9

7. Sh tdown and Maintenance 10

8. Tro ble Shooting 11-12-13

9. Drawings 14-15-16-17-18

10. Wiring Diagram 19

11. Spare Parts 20-21-22

12. Spare Parts & Service 23

ESWOOD OPERATING MANUAL ES-50 June 2011

MPORTANT

PRIOR TO INSTALLATION

Installation m st be carried o t according to local reg lations by

q alified trade persons. Isolating switch(es), sh t-off valves etc m st

be within easy reach of the machine for f t re service and

maintenance req irements. If in do bt call ESWOOD AUSTRALIA or

their representative for f rther information. No responsibility will be

accepted for defects or damages by improper installation, for

changes to the prod ct not a thorised by ESWOOD AUSTRALIA, or

for operation o tside the technical specifications.

ESWOOD AUSTRALIA warrants their prod cts to be free from

defects in material and workmanship nder "normal se and

service". This does not incl de normal wear and tear of parts.

ESWOOD AUSTRALIA will repair or replace any parts, which in

ESWOOD AUSTRALIA's sole j dgement are defective in material or

workmanship, in accordance with the warranty offered.

This ndertaking covers the provision of labo r and parts for 12

months from the date of delivery to the p rchaser. This ndertaking

applies only to state capitals. Remote areas are not covered by this

commitment and special enq ires sho ld be made. (Note: Tr vel

time not covered by w rr nty)

In no event will ESWOOD AUSTRALIA be liable for loss of facilities

or other property and s ch things as, b t not limited to, additional

labo r costs, loss of reven e or anticipated profits, and other

damages of any kind whether direct, indirect, incidental or

conseq ential.

Labo r nder warranty is s pplied free of charge d ring normal

working ho rs, Monday to Friday. Sho ld warranty work be

req ested o tside or o r normal working ho rs a labo r charge will

be applied eq ivalent to a normal ho r rate witho t o t of ho rs

penalty rates. (Refer to last page of this man al for yo r closest

branch for Warranty repair services)

Note: It is the responsibility of the owner to ens re the water feed to

Eswood Dish and Glass washers is of a q ality that will not form

excessive b ild p of calci m and other dissolved minerals on the

heating elements. Premat re fail re of heating elements that exhibit

this ca se of fail re will not be covered nder warranty.

ESWOOD OPERATING MANUAL ES-50 June 2011

ENERAL DESCRIPTION

Awesome Perform nce: The ES50 is a high performance pass-

thro gh dishwasher b ilt to meet the needs of b sy commercial

kitchens, catering for aro nd 250 seats. It has two powerf l p mps

for washing and rinsing, and high flow wash and rinse jets that

provide fast and efficient cleaning performance.

User Friendly Autom tic Oper tion: Simply open the hood, slide

the rack in and close the hood to begin the a tomatic operation. A

safety switch ens res that the machine does not operate nless the

hood is properly closed, and a reliable and acc rate solid state

timer provides a choice of three cycle times. The ES50 feat res a

f ll wraparo nd handle with s per smooth, wear resistant

copolymer g ides and pivot b shes, and two adj stable co nter-

balance springs. It also has digital thermometers for the rinse and

wash water, cycle stat s lights and cycle selection controls, all

conveniently located for easy se.

Convenient Design: The bench height pass-thro gh operation is

efficient and safe, with operators simply sliding racks in and o t of

the wash chamber from an adjoining bench. The ES50 easily

adapts to in-line or corner feed layo ts, and the compact size will

easily fit any kitchen.

The ES50 has an attractive and easy to clean satin finish stainless

steel cabinet. Wide strainer pans prevent p mp, drain and wash

arm blockages, and the wash and rinse arms, strainer pans and

overflow t be are easily accessible from the front of the machine

and are all removable by hand.

F st Low Cost Inst ll tion: Simply connect the hot water s pply,

connect the trap to the drain o tlet, and connect the wiring.

Powerful W sh nd Rinse Systems: Independent wash and rinse

arms, both above and below the rack, provide fast and thoro gh

washing, while the a to-spin drain system gives a sparkling finish

by preventing s ds from dripping from the wash arm d ring the

rinse cycle.

ESWOOD OPERATING MANUAL ES-50 June 2011

The wash and rinse water s pply tanks are fitted with a tomatic

level and temperat re controls to ens re hygienic operation, even

d ring high-demand sit ations.

Qu lity, Reli bility nd Perform nce: Eswood has a rep tation

for prod ct reliability that is second to none. The finest of stainless

steel and d rable synthetic materials are sed, and all Eswood

prod cts are f lly g aranteed and backed by a national s pport

network. The ES50 satisfies the National Standards for Pl mbing

Safety and complies with Health A thority reg lations.

ESWOOD OPERATING MANUAL ES-50 June 2011

ECHNICAL SPECIFICATIONS

M chine Specific tions

Net Weight 130kgs

Ho rly Capacity 1080 pieces of tableware/ho r

Wash Cycle Times Selectable: 60, 80 or 100 seconds

Dwell/Rinse Cycles 5 seconds/13 seconds

Standard Eq ipment C p Rack 500x500mm (1)

Plate Rack 500x500mm (2)

C tlery Containers (2)

W sh Pump, T nk nd Element

Wash P mp 700 L/min, 1.0 kW

Wash Tank Capacity 45 Litres

Wash Tank Heater 2.8 kW

Wash temperat re 60

C to 70

Rinse T nk nd Element

Rinse P mp 375 Watts

Rinse Tank Capacity 12 Litres

Rinse Tank Heater 5.6 kW

Rinse Temperat re 82

C minim m

Water Cons mption 4 Litres per cycle

Electric l nd W ter Connections:

Electrical Inp t 415/50/3N, 10 kW

Water Inp t 65

C minim m @ 100-400 kPa

Hot Water Inlet

” B.S.P. fitting

Drain O tlet 2” B.S.P. gravity fed

ESWOOD OPERATING MANUAL ES-50 June 2011

NSTALLATION

1. Remove the packing materials from the machine, incl ding

inside the chamber.

2. Remove the lower panel, position the machine and level by

t rning the adj stable feet.

3. Fit a line strainer to the water s pply.

4. Connect the 2” B.S.P. gravity drain via a 2” trap to the drain

o tlet.

Note that all pl mbing work is to be done in accordance with

local pl mbing codes.

5. Connect the hot water inlet to a

” B.S.P. isolating valve

adjacent to the machine. The hot water inp t s pply sho ld be

at a minim m of 65

C and between 100 to 400kPa. A press re

red cing valve sho ld be fitted for press re above 400kPa.

6. Ens re that the rotary switch is “OFF”, then open the control

panel and connect the 3-phase power to L1, L2 and L3. Next,

connect ne tral to “N” on the terminal block and connect the

earth wire to the earth terminal. An isolator is also req ired

adjacent to the machine. When finished, check that the

direction of rotation of the rinse and wash motors are in

accordance with the arrows on the motor ho sings.

Note that all electrical work is to be done in accordance with

the rating plate on the lower panel.

7. Connect the benching so that there is a fall back towards the

machine to allow water to drain back into the machine.

ESWOOD OPERATING MANUAL ES-50 June 2011

NITIAL START

UP PROCEDURE

1. With the rotary switch and isolator “OFF”, open the hot water

s pply to the machine. This allows the break tank to fill. When

f ll, the water level sho ld be approximately 20mm below the

overflow slot in the rear of the tank. The level can be inspected

by removing the lid from the break tank.

2. With the rotary switch still off, t rn the power on at the isolator.

3. Check that the drain overflow pipe and strainers are in position.

4. If the machine is fitted with an a tomatic detergent injector,

place the free end of the 10mm clear plastic t be, located

nder the machine, into a 4 Litre or other s itable container of

liq id detergent. The nit will prime itself after a few cycles.

Do not se wrong prod cts as they will void the warranty, and

se prod ct in accordance with the man fact rers’

recommendations.

5. With the hood open, t rn the rotary switch to “FILL” and close

the hood. The machine will begin filling and the pilot light will

ill minate ntil the cycle is complete. Open the hood and check

that the water is p to the overflow level. If not (see 8. Tro ble

Shooting), repeat the “FILL” cycle ntil the overflow level has

been reached.

6. With the hood open select the Short, Medi m or Long wash

cycle sing the rotary switch.

7. Close hood to start the wash cycle. The pilot light Ill minates

ntil the cycle is complete. When finished, check for leaks.

8. T rn the rotary switch “OFF”, open the door and remove the

overflow t be to drain the machine.

9. Replace the lower panel.

ESWOOD OPERATING MANUAL ES-50 June 2011

ASHING OPERATION

1. Check that the strainers are clean and that the strainers and

overflow t be are in position.

2. With the hood raised, t rn the switch to “FILL” and then close

the hood. The cycle light ill minates while the machine is filling.

3. When the machine has finished filling, open the door and

check that the water is p to the overflow level. Repeat step 2 if

the overflow level has not been reached (and see 8. Tro ble

Shooting).

4. Select the Short, Medi m or Long washing cycle, depending on

the degree of soiling. This also activates the wash heater

element.

5. Scrape off any loose food matter from the dishware and place

the items in an appropriate rack. If no a tomatic detergent

dispensing eq ipment is fitted (see detergent companies) add

of a c p of non-foaming commercial dishwashing detergent

into the washtank. Slide the rack into the machine and close

the door. The cycle light ill minates d ring the cycle.

When loading racks, face the plates in the direction of feed into

the machine. Load the small items at the front and the large

items at the back.

Note that the cycle will not begin ntil the water in the booster

has reached 82

6. When the washing is finished, lift the hood and remove the

clean rack. To wash another rack repeat from step 5. If no

a tomatic detergent dispenser is fitted, add one teaspoon of

detergent after every fo r to five washes.

Note that the hood sho ld not be opened ntil the wash and

rinse cycle is complete, otherwise the cycle will reset and

contin e longer than necessary.

ESWOOD OPERATING MANUAL ES-50 June 2011

HUTDOWN AND MAINTENANCE

1. T rn the rotary switch "OFF".

2. Remove the strainers and overflow t be and drain the wash

tank.

3. To fl sh o t food scraps from the inside of the machine, close

the hood and t rn the rotary switch to “FILL”. At the end of the

cycle t rn the switch to “OFF” and lift the hood.

4. Clean the strainers nder a tap, then replace the overflow t be

and strainers.

5. Check that the rinse and wash arms and jets are free of foreign

matter. If necessary, remove the arms and jets and clean

them.

A) Remove the kn rled screw above the rinse arm and slide

the rinse arm off. Remove the end caps and prick the jets with

a paper clip or similar item and fl sh the jets nder a tap. Refit

the end caps.

B) Place a small screwdriver thro gh the holes of the rinse

arm bearing shaft and nscrew. Slide the wash arm off, then

prick the jets and fl sh them nder a tap.

C) To reassemble reverse the proced re, being caref l not

to overtighten the shaft or screw.

6. Clean the exterior of the machine with a damp sponge. Do not

pass water over the electrical controls and avoid abrasive or

strong detergents.

7. Check for leaks and ens re that the lower and pper arms

rotate freely.

8. Leave the hood open to allow the machine to air.

Table des matières

Autres manuels Eswood Lave-vaisselle

Eswood

Eswood UC25 Manuel utilisateur

Eswood

Eswood B42GN Document technique

Eswood

Eswood ES-220 Document technique

Eswood

Eswood ES32 Document technique

Eswood

Eswood CI-3B Document technique

Eswood

Eswood UC25NDPLT Document technique

Eswood

Eswood ES-100 Document technique

Eswood

Eswood IW-3N Document technique

Manuels Lave-vaisselle populaires d'autres marques

Electrolux

Electrolux ESI5211LOX Manuel utilisateur

KitchenAid

KitchenAid KUDB230B Manuel utilisateur

Brandt

Brandt BDJ424DB Manuel utilisateur

Asko

Asko DSD767UXXL.AU Manuel utilisateur

Beko

Beko DFN26210W Manuel utilisateur

NEFF

NEFF S153ITX00E Fiche technique

Midea

Midea SV 4.45 wi Manuel utilisateur

LG LDF7932 Manuel utilisateur

Gorenje

Gorenje GV63214 Manuel utilisateur

Hotpoint

Hotpoint HDA1100ZWH Manuel de service

Blomberg

Blomberg LDFN2240W Manuel utilisateur

AEG

AEG FFB83836PM Manuel utilisateur

Cylinda

Cylinda DM3220RFD Manuel utilisateur

Atag

Atag DW8214MB Manuel utilisateur

GE GLD8000 Series Manuel utilisateur

Siemens

Siemens SN23HI02KE Fiche technique

Omega

Omega ODW717X Manuel utilisateur

BORETTI

BORETTI BVW-683 Manuel utilisateur