Estate Swing EST-64 Manuel utilisateur

T-

-6

User Manual

EST

GSM Remote Control Device

EST

–

USER MANUAL

–

Rev.2

–

Tec nical Support:

800

640

4283

Estate Swing

Electronic KIT to convert your gate into a GSM gate

EST-64 GSM Remote Control Device Diagram

EST

GSM Remote Control Device

EST

–

USER MANUAL

–

Rev.2

–

Tec nical Support:

800

640

4283

Estate Swing

EST-64 GSM Remote Control Device is an electronic board manufactured b Estate

Swing that links to a SIMCOM 300 GSM module, supplied with it.

The purpose of this device is to be installed in parallel of the low voltage opening button

of an electric gate to enable it to be opened b means of a GSM phone.

It has a rela whose contact has to be connected in parallel with the button which opens

the gate. It has a White List of numbers who are enabled to open the phone, up to 64.

When the EST-64 GSM Remote Control Device receives a call, it will check to see if the

calling number is in the list. If it is in the list it will reject the call (so there will be no

charge – at least with toda ’s charging procedures) and click the rela momentaril .

1) Safe – nobod can clone our phone as easil as the can do with a standard remote

control

2) Flexible – ou can add or remove an bod number in a minute with an SMS

3) Cheap – ou don’t need to bu a remote control for each member of our famil

4) Convenient – no matter if ou change car, or if ou have different gates to open.

Your phone will alwa s be with ou all the times our remote controls were

somewhere else!

Installation

To install the EST-64 GSM Remote Control Device ou need to connect the 2 wires of the

rela contact in parallel with the gate opening button. The rela contact can stand 48V

1A maximum, this is enough for its operation but don’t try to switch higher voltages

or currents.

You also need to provide the power b means of 12 to 20 VAC or 12 to 26 VDC. The

power suppl must be able to stand 2A. We suppl a proper AC adapter. If ou are not

using our AC adapter, make sure the power suppl can arrogate 2A. Don’t use telephone

INTRODUC

TION

ADVANTAGES OF

EST

GSM REMOTE CONTROL DEVICE

EST

GSM

REMOTE CONTROL DEVICE OPERATING INSTRUCTIONS

EST

GSM Remote Control Device

EST

–

USER MANUAL

–

Rev.2

–

Tec nical Support:

800

640

4283

Estate Swing

batter chargers! Most of them rel on the phone batter and are unable to suppl the

power needed.

You should install the EST-64 GSM Remote Control Device in a place where there is GSM

signal coming from the operator ou want to use. Check it with a phone before

proceeding with the installation. If ou need to install the device in a place with little

signal, ou ma consider using an external antenna that we ma suppl as an option to

be purchased separatel with 5m cable.

You should then insert the SIM of the operator ou want to use and program in the

White List the numbers enabled to open the gate using the command WHL.

Note:

You must remove t e PIN request from t e SIM before inserting it in t e unit,

otherwise the device will not work. In order to do so, insert the SIM in a phone and

disable the PIN request (usuall there is a securit menu that enables ou to do so). If

ou don’t do it, and switch-on the unit more than 3 times ou will have to reset the PIN

using the PUK!!

You can program the EST-64 with SMS commands using our phone. It is safe to do so

because in addition to the fact that other people ma not know the number of the SIM

inserted in it, we also use a Password that makes it impossible for an bod , who doesn’t

know it, to access the s stem b chance.

Remember that commands must be CAPITAL LETTERS. It is PWD not pwd, CAP not Cap

etc.

Don’t add spaces or an other character.

The 2 SMS commands that ou will certainl use in the EST-64 GSM Remote Control

Device are the following:

#PWD: Password

#WHL: White List (adds or removes numbers)

You could also use the following, though not necessaril :

#ACM: Access Mode

#CAP: Change password

EST

PROGRA

MMING INSTRUCTIONS

EST

GSM Remote Control Device

EST

–

USER MANUAL

–

Rev.2

–

Tec nical Support:

800

640

4283

Estate Swing

#GOT: Gate pulse time

#CSQ: Check Signal Qualit

Once ou issue a command with an SMS, ou will receive a confirmation SMS with OK if

ever thing is correct or Error if there is an Error

#PWD

Password. This command must alwa s come first. Use 6 digits as a password.

The standard default one, when the device comes from the factor , is 123456.

We suggest that ou change it, using the #CAP command.

In all the following examples we will use 12 456 as an example of password.

#WHL

White List. This is the command that ou will use most. It is used to add or remove

numbers that are enabled to open the gate into the White List. You can add up to 64

numbers in the list. Ever position must be indicated in the command and we advise ou

to keep a list written somewhere to know which numbers are in and in which position

•To add a number, the s ntax of the command is the following:

#PWD123456#WHL01=3593334444

Where 01 is the position in the list and 3593334444 is the number enabled.

Please note that it is possible to program up to a maximum of 10 digits for a

number. If it has more digits ou should use the rightmost ones. For example, if

our number is 33446665555 ou should program 3446665555.

If our number appears as +393489999888 ou should not program the countr

code (+39). If our number has onl 9 digits or less, it is not a problem. The

important thing is that ou don’t exceed 10 digits.

•To check which is the number in a place of the list:

#PWD123456#WHL01?

•To erase a number:

#PWD123456#WHL01D

•To erase all number

#PWD123456#WHL99D

#ACM

Access Mode. This command allows you to open only to people that are in the white list

or to anybody calling the SIM number.

•#PWD123456#ACM0 (it is a zero)

EST

GSM Remote Control Device

EST

–

USER MANUAL

–

Rev.2

–

Tec nical Support:

800

640

4283

Estate Swing

Warning! With the above command ou allow free access to an bod calling!!

•#PWD123456#ACM2

With the above command ou allow onl people that are in the white list. This is the

standard and recommended option.

#CAP

Change Password. Use this command to change the password with a new one that ou

will chose for our device (don’t forget it or ou will have to send the unit back to us to

reset it, and this has a cost!)

The #CAP command must be issued 2 times to be sure ou don’t digit a wrong one. Of

course it must be preceded b the old password.

For example, to change the password 123456 into the new password 333444 ou need

to send the following SMS:

•#PWD123456#CAP333444#CAP333444

You will receive a confirmation with CAP OK if ou wrote correctl .

#GOT

Gate pulse time. This command is useful in case ou need to keep the button pressed

longer. The standard time is 1 second (Maximum 60 seconds) where 01=1 second,

06=60 seconds. You can change it with the GOT command.

The s ntax of the command is the following:

•#PWD123456#GOT02

With the above command the opening time has been set to 2 seconds.

#CSQ

Chec GSM signal quality. This command is useful to see what is the GSM network signal

level our EST-64 GSM Remote Control Device is receiving.

If ou send the command: #PWD123456#CSQ?

You should receive an SMS with signal qualit in range 0 to 31 (if it is 0 we doubt it will

ever answer…). You should have a signal above 12 to be sure of being able to open the

gate in an condition. Better if above 16. You should add an external antenna if this is

EST

GSM Remote Control Device

EST

–

USER MANUAL

–

Rev.2

–

Tec nical Support:

800

640

4283

Estate Swing

not the case, or eventuall even change operator with another that serves our area

better.

The EST-64 also comes with additional 1 Input and 1 Output. The output is connected to

an on-board rela which can be activated b sending an SMS command. The Input can

be used to generate alarms when triggered. It also can be programmed to count the

input active pulses up to 1ms fast or activate the output rela .

Note: When used as counters input wor only in ACTIVE HIGH mode. They count ONLY

High Going Pulses.

One of the most important functions is to receive alarms. In order to do this properl ,

ou must program the administrator numbers, turn on the function of the input and tell

the EST-64 which are the recipient numbers and who should receive the alert message

for the particular input.

The 8 administrator numbers can be programmed with a text command via SMS.

Text Command:

#TEL[N]=XXXXXXXXXX

N stands for administrator number 1 – 8 (position)

XXXXXXXXXX stands for the phone number ou want to program as administrator.

•To add a number, the s ntax of the command is the following:

#PWD123456#TEL1=3593334444

Please note that it is possible to program up to a maximum of 16 digits for a number.

ADDITIONAL INPUT & OUTPUT PROGRAMMING INSTRUCTIONS

5.1

INPUT SETTINGS

5.1.1

PROGRAMMING THE ADMINISTRATOR NUMBER

EST

GSM Remote Control Device

EST

–

USER MANUAL

–

Rev.2

–

Tec nical Support:

800

640

4283

Estate Swing

•To check all the administrator number in the list:

#PWD123456#TEL?

Note: Programming the administrator numbers is necessary in order to operate all the

below functions and to receive text alerts when the relays activated.

The unit can onl send text alerts to 1 or all 8 of the programmed administrator’s mobile

phone numbers and this function can be changed at an time b sending the following

commands b SMS message to the unit.

Text Command:

#RERN=XXXXXXXX

XXXXXXXX stands for 8 digits value: ON (1) or OFF (0) for the 8 administrators

For example, if ou assume onl administrators 1, 2, 3, and 4 are to receive text alerts

ou would send the following SMS message to the unit.

•#PWD123456#RERN=11110000

Note: You can onl put 1 in the first 4 digits of the text command if there are onl

phone numbers stored in #TEL1, #TEL2, #TEL3 and #TEL4. The rest should be 0.

•To check the setting of which recipient will receive alert messages

#PWD123456#RER?

The Input Alert Message can be edited and programmed up to 100 characters long. You

can change the displa ed text b sending the following commands b SMS message to

the unit.

Text Command:

5.1.2

SETTING THE RECIPIENT THAT WILL RECEIVE ALERT MESSAGE

5.1.3

EDITING THE INPUT ALERT MESSAGE

EST

GSM Remote Control Device

EST

–

USER MANUAL

–

Rev.2

–

Tec nical Support:

800

640

4283

Estate Swing

#STR=XXXXX…

XXXXX stands for the displa text that ou want to program

For example, if ou want the alert message to displa “Garage Opened!” when

received a text alert; ou would send the following SMS message to the unit.

•#PWD123456#STR =Garage Opened!

To turn on the function of input, ou can send the following commands b SMS message

to the unit.

Text Command:

#CTR=X

X stands for ON (1) or OFF (0) value

•To turn on the input, the s ntax of the command is the following:

#PWD123456#CTR=1

An alert message will be sent when the increment of alarm counter reaches the alert

value (Default: 500). It is possible to set the alert value up to maximum value of

65535 times. To set the counter alert value of input, ou can send the following

commands b SMS message to the unit.

Text Command:

#COA=XXXXX

XXXXX stands for 5 digits value: The number of times

For example, assume ou want it sends a counter alert message each time the input has

triggered for 5 times, ou would send the following SMS message to the unit.

5.1.4

TURN ON THE FUNCTION OF INPUT

5.1.5

SETTING THE COUNTER ALERT VALUE FOR INPUT

EST

GSM Remote Control Device

EST

–

USER MANUAL

–

Rev.2

–

Tec nical Support:

800

640

4283

Estate Swing

•#PWD123456#COA=00005

This input can be programmed to behave differentl , it can count the input active high

pulses, generate an alarm message or activate rela . To program the input, ou can

send the following commands b SMS message to the unit.

Text Command:

#CTC=F

F stands for input function 1 - 5

Function Descriptions

Function 1:

•Function as counter

•Sends a counter alert message once alarm counter reaches the alert value

Function 2:

•Function as counter

•Activate the output rela 2 to sta on

•Sends a counter alert message once alarm counter reaches the alert value

Function 3:

•Function as counter

•Activate the output rela 2 to sta on

•Sends an alert message once triggered

•Sends a counter alert message once alarm counter reaches the alert value

Function 4:

•Function as counter

•Activate the output rela 2 for 1 second

•Sends a counter alert message once alarm counter reaches the alert value

Function 5:

•Sends an alert message once triggered

5.1.6

SETTING THE FEATURE FOR INPUT

Table des matières

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation