ESICAM HN03 Manuel utilisateur

EN Introduction

Please read these instructions carefully in their entirety before using the product, and keep them handy for

future reference.

Thank you for your interest in our product and for ordering the IPCam. It can be controlled using any PC/laptop via the

Intranet or Internet via a common web browser (recommended: Internet Explorer or Safari), via smartphone (iPhone, iPad,

Android phone and pad) or via the client software installed on the PC. It can be easily integrated into your LAN or WLAN

environment via a user-friendly installation process and intuitive interface. We are certain that you will value the quality

and features of this product.

Note

This product can interfere with other wireless devices that

use the 2.4 GHz ISM band. Please turn off these devices to

avoid interference.

Product safety

This product transmits electromagnetic waves just like

other wireless products. Its signal power, however, is less

than other wireless devices, for example, mobile phones.

During operation, IPCam meets the safety standards for

radio frequencies and the recommended indices.

Restrictions

1. Do NOT use this product to violate the privacy rights

of others. Monitoring the activities of other people wi-

thout their consent is unlawful. This product was not

designed or manufactured for this purpose.

2. Do NOT place this product in proximity to medical

devices. Radio waves can cause the malfunction of

electronic medical devices.

3. This product should be kept at least 30 cm away

from all pacemakers. Radio waves can interfere with

pacemakers.

4. Do NOT use this product for unlawful activities. The

user must ensure that the camera is only used in ac-

cordance with the law.

Care and maintenance

1. Make sure that the camera and its power supply has

sufficient ventilation;

2. Do not shake, hit or allow the product to fall to the

ground;

Do not place this product in proximity to magnetic

objects;

Do not place the product in locations that have con-

stant temperature or humidity fluctuations;

Keep the product away from heat sources;

Do not use this product in proximity to aggressive

chemicals;

Do not use this product in proximity to water;

Do not place this product in rooms that are surroun-

ded by metal. The surrounding metal can shield elec-

tromagnetic waves so that no signal is received;

10.

Please note the local environmental protection regula-

tions of your area;

11.

Please turn the device off when not in use;

Do not take the product apart and do not attempt to

repair it. This can damage the product.

Main features

Easy installation

The camera comes with an integrated wireless capability

(IEEE802.11b/g/n) and web server function. Therefore, dri-

ver installation is not necessary. Thanks to P2P technology

(peer-to-peer), the user can view the IPCam stream easily

via a PC/smartphone/client software by simply entering

the UID/password. The router and firewall do not need to

be configured. The camera can automatically speak to the

router via the network cable or WLAN. You can see images

and hear noises picked up by the camera in the remote

stall as soon as the connection is made.

802.11 b/g/n WLAN connection available

The camera was designed to work with both wired net-

works as well as standard 802.11 b/g/n wireless networks.

The camera has SSID filtering, powerful 64/128 bit encryp-

tion and the latest security standard for WPA encryption in

order to protect against illegal access.

3GPP mobile surveillance

The camera allows you to view images on your mobile

phone as a live video stream. It supports the telecommu-

nication standard for the 3GPP streaming format. All 3G-

capable mobile devices and most 2G mobile phones that

support the 3GPP standard are compatible. This means

that the images can be viewed via your mobile phone's

browser.

Simultaneous high-speed MPEG-4 and Motion JPEG

The camera enables the simultaneous live streaming of

MPEG-4 and Motion JPEG. The camera has H.264/MPEG4

compression that compresses the video to make the trans-

mission faster and more efficient. The H.264/MPEG4 and

MJPEG image can be transmitted at 30 frames per second.

Simultaneous HTTP and RTSP streaming

The camera supports the HTTP and RTSP/RTP/RTCP proto-

col and supplies several HTTP and RTSP streams simulta-

neously.

Snapshot and record function

You can take a snapshot from the images sent to your PC

by the camera and then save the image in JPG or BMP

format. In addition, you can also record the video and

audio stream sent from the camera to your PC and save it

in ASF format.

Motion sensor function

The camera can detect changes to the image being

viewed. As soon as a change occurs, it sends an e-mail to

e-mail addresses with a video file or a snapshot as an at-

tachment. The video file or snapshot can also be uploaded

to an FTP server. In addition, the camera can also be confi-

gured so that it sends images at regular intervals.

OSD function

The OSD function (on screen display) can show the system

name, date and time, and user-defined info on the screen.

Authentication

You must enter your user ID and password in the authenti-

cation window. The password prevents unregistered users

access to your camera. Users can select between the basic

authentication method or the direct access authentication

method.

Multiple access

The camera enables access for up to 4 users simulta-

neously. Please note that the output of moving images

can decrease as more users connect to the camera simul-

taneously.

Infrared night vision

The camera uses infrared LEDs. When the environment is

dark, the LEDs activate automatically via a light sensor.

The video switches from colour to black & white. The

range is approx. 11 m. It is possible to switch the LED ope-

ration from "auto" to "manual".

Adapter

When using the power adapter, make sure that the nomi-

nal voltage matches that of the device to avoid damage

due to incorrect use of the power supply.

Main features

PC system requirements

The PC and network must meet the following

technological specifications in order for the camera to

function.

Processor: Intel Pentium III, 1GHz or higher

(Pentium IV, 2 GHz or higher recommended)

RAM: 256 MB or more

Colour monitor: We recommend at least 800 x 600

and the latest driver for the display adapter

Operating system: Microsoft Windows 98 /

Windows ME / Windows 2000 / Windows XP /

Windows Vista / Windows 7 / Windows 8

Web browser: Internet Explorer Version 5.0 or higher,

DirectX 9.0c or higher, Safari, Firefox (requires

QuickTime), Google Chrome (requires QuickTime)

Network protocol: TCP/IP network protocol installed

Interface: 10/100 Mbps Ethernet connection or

wireless network connection (WLAN)

Technical data #HN03

Imagesensor: 1/4" Progressive CMOS sensor

Displayresolution: 1280x720Pixels

Lens: 3,6 mm fixed lens

Viewingangle: 56,14°

min.illumination: 1.0 Lux / F1.2

Video

Imagecompression: H.264, MJPEG/JPEG

Imageresolution: HD 720p (1280x720 Pixels) /

VGA (640x480 Pixels) / QVGA (320x240 Pixels)

Framerate: 720p/VGA/QVGA15 fps

Bitrate: CBR/VBR, outputrange: 32 kbps ~ 40 Mbps

Infraredmode: Automatic/DualFilter

Night vision: 30IRLEDs,ca. 15 m distance

Network

Ethernet: 10/100 Mbps, RJ-45

Supportedprotocols: TCP/IP, HTTP, RTSP, TCP, UDP, SMTP,

FTP, DHCP, DNS, DDNS, NTP, UPnP, P2P, etc.

Wirelessstandard: Wi-Fi (IEEE802.11b/g/n)

SupportIPaddress: static, dynamic

max. number concurrent users: 4

HardwareInterface

Storage: MicroSD card(max. 32 GB, not included)

Power supply: DC12V/1.0A

Others

Waterproof level : IP65

Operatingtemperature: -20 ~50 °C

Operatinghumidity: 10~ 80 %

Weight: 620 g

Accessory: Camera, power adapter, Wi-Fi antenna,

network cable, user Manual

Warranty: 1 year

Technical data #HN11

Image sensor: 1/4“ Progressive CMOS sensor

Display resolution: 1280x720 pixels

Lens: 3,6 mm

Viewingangle: 51 ~ 24 ˚

min.illumination: 0.8 Lux / F1.4 (color mode), 0.3 Lux /

F1.4 (B&W mode)

Video

Imagecompression: H.264

Imageresolution: HD 720p (1280x720 Pixels) / VGA

(640x480 Pixels) / QVGA (320x240 Pixels)

Frame rate: 720p/VGA/QVGA0-15 fps

Bitrate: CBR/VBR, outputrange: 32 kbps ~ 40 Mbps

Infraredmode: Automatic/DualFilter

Night vision: 22 IR LEDs, IR distance: 10m

Network

Ethernet: 10/100Mbps, RJ-45

Supported protocols: TCP/IP, HTTP, RTSP, TCP, UDP, SMTP,

FTP, DHCP, DNS, DDNS, NTP, UPnP, P2P, etc.

Wireless standard: Wi-Fi (IEEE802.11b/g/n)

Support IP address: static, dynamic

max. number concurrent users: 4

HardwareInterface

Storage: MicroSD Card(max. 32 GB, not included)

Power supply: DC5V/2.0A

Power consumption: Typical: 3.5 W (IR LED turned on) /

max: 7 W (P&T turned on)

Pan/Tilt angle: Horizontal: 355°,Vertical:85°

Others

Waterproof level: IP65

Operatingtemperature: -20 ~ 50 °C

Operatinghumidity: 10 ~ 80 %

Weight: 1200 g

Accessory: Camera, power adapter, Wi-Fi antenna,

network cable, user Manual

Warranty: 1 year

under the relevant icon.

2.1.3 Scan the QR code as bellow:

2.1.1 Enter the www.eyecloud.so website, and click

IOS Android

Camera setup and conﬁguration

1. Connecting the camera to the network

When using for the first time, please connect the camera

and the computer to a router using network cables.

Ensure that the router is switched on and that, when the

RJ-45 cable is connected to the camera, the yellow and

green light illuminates (network control lights). Only use

the cable supplied to provide power to the camera so as

to avoid damaging the device!

The camera can be returned to the factory settings by

pressing the „Reset“ button (for at least 10 seconds).

The „Reset“ button is located on the underside of the

device.

2. Connect the camera with an Android /

iOS device (smartphone, tablet, etc.)

2.1 Software download

The software needed (EyeCloud) can be downloaded via :

„Download“

2.2 Registration

application with your e-mail address and password

2.1.2 The AppStore/Google Play by search "EyeCloud"

Camera setup and conﬁguration

2.3 Add a camera with the software

from the App store

Click „+“ at the top right to add a new camera, and

select „IP Camera“. There are four options for choosing

a camera:

Quick Setup: Pressing the WPS button on the camera and

router links the camera automatically (does not work with

every router)

LAN search: Click „Search“ to find the camera on the

network. The default password is 888888 and the user-

name is admin. Change these details as soon as you find

the camera in order to protect your privacy as effectively

as possible

Scan: Click „Scan“ and allow your smartphone to scan

the QR code. If you hear a beep, the code has been scan-

ned in and the unique camera number (UID) appears in

the relevant field.

Manual entry of the UID code: You can also enter the

UID manually. Please note that the entry is case-sensitive.

Once you have successfully installed the camera, click the

relevant icon and the camera appears.

2.4 Video options

Snapshot

Record

Listen

Talkback

Horz Cruise

Vertical Cruise

Horizontal

Vert Mirror

Night Vision

Preset Cruise

2.5 WLAN setup

Click the „House“ icon at the top left and the main menu

appears. Clicking „Device Management“ gives you a list

of all the cameras that have been installed on the network

via LAN cable.

Click the „>“ symbol on the right next to the camera to

activate the settings. Click the blue „WiFi“ icon to display

the WLAN networks available.

Choose a router and enter the password (WPA or WPA2).

Once you have confirmed this by clicking the „OK“ sym-

bol, the WLAN network is set up.

Now disconnect the camera from the RJ-45 cable.

The camera will dial in and connect automatically

to your network.

2.6 Add a camera with the software

from the Google Playstore

Scan: Click „Scan“ and allow your smartphone to scan

the QR code. If you hear a beep, the code has been scan-

ned in and the unique camera number (UID) appears in

the relevant field.

LAN search: Click „Search“ to find the camera on the

network. The default password is 888888 and the user-

name is admin. Change these details as soon as you find

the camera in order to protect your privacy as effectively

as possible

Manual entry of the UID code: You can also enter the

UID manually. Please note that the entry is case-sensitive.

Once you have successfully installed the camera, click the

relevant icon and the camera appears.

2.7 Video options

Horizontal cruise

Vertical cruise

Preset position

Full screen

Sound off

Sound on

No communication

Communication

Snapshot

Record

The application supports settings for the alarm, saving,

password changes, firmware updates, image quality

(brightness, contrast, mirroring, infra-red options).

The commands are self-explanatory thanks to the icons

and are easy to understand.

2.8 WLAN setup

Click the symbol on the right next to the camera to activa-

te the settings. Click „Setting“ and „WiFi Setting“.

The available WLAN routers are listed. Choose a router

and enter the password (WPA or WPA2). Once you have

confirmed this by clicking the „OK“ symbol, the WLAN

network is set up. Now disconnect the camera from the

RJ-45 cable. The camera will dial in and connect automati-

cally to your network.

2.9 Other settings

Delete camera: Select the camera and sliding it with the

finger on the touchpad to the left causes „Delete“ to ap-

pear. Tap it and the camera is deleted.

Reset to factory settings: Hold the reset button for

around 15 seconds.

Video history: Tapping „history records“ allows you

to list videos that have been stored locally and on the

SD card.

Version update: Tapping „Firmware upgrade“ searches

for new versions of the software.

3. Camera setup via PC software

Proceed in the same way as with downloading for smart-

phones and go to the www.eyecloud.so website.

Click „Download“ under the Windows icon.

Run the „app-Smart.exe“ file and allow the program

to install. The following icon appears on your desktop

following successful installation:

After double-clicking the icon, the following window

appears:

Recover: Forgotten password and request a new one

as the account)

After entering the details successfully, the program inter-

face appears. Pressing „+“ allows you to add cameras.

Name: Assign a unique name so that you know which ca-

mera you want to control if you have multiple cameras.

UID: Here, you can either enter the camera‘s unique code

that can be found on a separate sticker or click „Find“.

All of the cameras on the network are displayed (see Setup

via smartphone).

Click „Refresh“ if not all of the cameras on the network

are listed. Check during initial installation that all of the

cameras are connected with the RJ-45 network cable to

the router or that the cameras were linked correctly to the

WLAN.

Password: For security reasons, change your password

promptly and follow the instructions under „Modify

passwords“

Select WiFi: Clicking this button allows you to list the

WiFi networks available with a click on „Search signal“.

Select the appropriate network, click „Set“ and enter, if

requested, the WPA or WPA2 key. This is often found on

the underside of the router. After successfully setting up

the WLAN network, the following message appears

Confirm with „OK“. The camera is now successfully set

up! Now disconnect the camera from the RJ-45 cable.

The camera will dial in and connect automatically to your

network.

3.1 Operating the camera

• Display of the added cameras

• „+“: Add camera

• „-“: Delete camera

• „Cogwheel“: This is where you can set recording

and alarm functions

• Select menu for the number of cameras that are to be

displayed in the summary window. The setting from left to

right: Single camera, 4 cameras, 8 cameras, 16 cameras,

manual setting, full screen

• Start all: Bring all cameras online simultaneously

• Stop all: Take all cameras offline simultaneously

• Options: Settings for memory functions,

on-screen display and other details

• Video: Access to saved videos

• Alarm: Access to videos that were triggered due

to an alarm

• Settings: Change password, search for software

updates

Autres manuels pour HN03

Ce manuel convient aux modèles suivants

Table des matières

Manuels Caméra IP populaires d'autres marques

FLIR

FLIR Exx series Manuel utilisateur

Avigilon

Avigilon H4A-BO1-IR Manuel utilisateur

Digital Watchdog

Digital Watchdog DWCA-C128-64 Manuel utilisateur

ShareTech

ShareTech AV1 Manuel utilisateur

Ezviz

Ezviz C6C Manuel utilisateur

Melchioni

Melchioni UCAM 2015 Manuel utilisateur

Geutebruck

Geutebruck G-Cam/ESD-4630 Manuel utilisateur

Arecont Vision

Arecont Vision MegaBall AV3146DN-3310-D-LG Manuel utilisateur

Mitel

Mitel 6800i Series Manuel de service

Vitek

Vitek VTC-IR403-212NP Manuel utilisateur

THOMSON

THOMSON DSC - 323W Manuel utilisateur

AVer

AVer FB2027 Manuel utilisateur

ENFORCER

ENFORCER EV-T5105-N2SQ Manuel utilisateur

Wansview

Wansview NC543 Manuel utilisateur

Eneo

Eneo MCB-64A0003M0A Manuel utilisateur

deView electronics

deView electronics CBDNI36F Manuel utilisateur

Swann

Swann SwannEye Manuel utilisateur

LevelOne

LevelOne IP CamSecure Manuel utilisateur