Errebi M-BT Manuel utilisateur
M-BT
It can create and copy remotes of 280-400MHz (Extra EU), 433MHz, 868MHz,
both x code and Rolling Codes. You can do it by self-learning, by dedicated
App for your mobile, or by the PC program ERREBIREMOTESPRO.
YOUR KEY
www.errebispa.com
THE MOST COMPLETE REMOTE WITH THE
MOST ADVANCED TECHNOLOGY
COPY OR GENERATION
BY MOBILE APP
ErrebiRemotesPro App is available on Play store
and App store. It will help you for the copy, and
it gives the possibility to manage the advanced
functions the remote gets.
COPY OR GENERATION
BY PC PROGRAM
PC program permits you to use all the advanced
functions of the M-BT, like the generation of a
remote, and the copy of a FAAC slave.
SELF-LEARNING COPY
Copying in few easy steps, as indicated on
the back of the leaet, with no need for any
device.
ERREBI S.p.A. Unipersonale, Via Pianezze 42-49-32040 Cibiana di Cadore (BL) - Italy-tel.0435 542500 - fax 0435 542522 - [email protected] - www.errebispa.com
REMOTE
M-BT
Known xed code
ROLLING CODE, FIX CODE OR UNKNOWN
Press buttons 1 and 3 at the same time,
until led starts blinking red, release the bu-
ttons and wait for the led to stop blinking.
NOTE:
After this procedure, continue
from step 2.
NOTE:
If more than 10 Seconds pass without any activity, the M-BT remote will exit
the programming mode. Restart the programming.
*When copying a Rolling code remote, it will copy the selected button and
also the followings. It means that if choosing the button 2 of the M-BT, it will
copy the buttons 1,2 and 3 of the original on buttons 2,3 and 4 of the M-BT.
On x code remotes, it copies only the selected button of the original.
**If the original remote is a Telcoma or VDS, the second input will be given
pressing the button a second time.
** If the original remote is a BFT or ERREKA, press the hidden button in the
rear of the original, or, if your BFT doesn’t have it, press at the same time
buttons 1 and 2 of the original.
** If the original remote is a FAAC, press at the same time buttons 1 and 2
of the FAAC, until the led of the FAAC blinks, then release, and then press
again the button used for the rst input.
***Mode ( 1.Automatic/ 2.Manual/ 3.Clone/ 4. Scanner )
Press buttons 1 and 2 at the same time,
until led starts blinking red, release the bu-
ttons and wait for the led to stop blinking.
1
If the light blinks green, the copy is not
correct, try again put the original remote
closer or further away.
Press and release the button where you
want to copy the original remote (*). Led
lights red.
2
If the light blinks red, the copy is not co-
rrect, try again put the original remote clo-
ser or further away.
If the light turns red, it is a rolling code that
needs the second input.**
Give the second input from the original re-
mote until the M-BT light turns green.
Press the button of the original remote you
want to copy until the light of the M-BT tur-
ns green, then release.
3
If the green light turns off, the copy is done.
The process is over. If the light turn red, the remote can not be
copied.
If the green light blinks slowly it means that
the remote is a rolling code and it is copied
correctly.
Choose the copying mode***.the light will
turn off, and the copy is nished.
Autres manuels Errebi Télécommande
Manuels Télécommande populaires d'autres marques
Panasonic
Panasonic EUR7622KB0 Manuel utilisateur
Bang & Olufsen
Bang & Olufsen Beo4 Manuel utilisateur
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur
Multiplex
Multiplex PROFI TX 9 Manuel utilisateur
One Remote
One Remote RMB4 Manuel utilisateur
FUTABA
FUTABA 9ZAP - PART2 Manuel utilisateur
