Ericsson R320S Manuel utilisateur
Working Instruction, Standard
3/000 21-2/FEA 209 544/21 B Approved according to 1776-2/FEA 209 544
Working Instruction, Standard
Applicable for R320s, R320sc
Contents
1 Domeswitch........................................................................................................................2
2 Frame Assembly................................................................................................................2
2.1 Process Tools.......................................................................................................2
2.2 Instruction............................................................................................................3
3 Revision History.................................................................................................................3
Working Instruction, Standard
3/000 21-2/FEA 209 544/21 B 2(3)
1 Domeswitch
Important about soldering operation!
When any kind of soldering operations is done on the back of PCB or near the domeswitch
it must be removed and replaced with a new one
# Figure Instruction Note
1 Domeswitch replacement
2
fig.1
Remove the old domeswitch
with a pair of tweezers (fig.1).
3 Brush/Clean the board surface.
4 Take a new domeswitch
5
fig.2
Place the new domeswitch on
the board, use the guiding
holes and the connection point
for the EL-lamp for correct
positioning (fig.2).
Make sure that the
domeswitch is correct
assembled and that the
washer is right positioned.
2 Frame Assembly
2.1 Process Tools
• Hotmelt glue gun.
• Tweezers.
Working Instruction, Standard
3/000 21-2/FEA 209 544/21 B 3(3)
2.2 Instruction
• Dismount the phone as described in Mechanical Instructions 3/00021-1/FEA 209
544/21 (Disassembly).
# Figure Instruction Note
1
fig2.1
Remove the vibrator assembly
from the old frame. (fig 2.1).
2 Take a new frame assembly.
3 Mount the old vibrator
assembly the RF-gasket in the
frame.
4
fig2.1
Mount marking labels on the
three µBGA components
(fig2.2).
Don’t cover the grounding
surface on the board with
the labels.
5 Apply three glue spheres on
the paper labels with a
diameter about 3-5mm.
Exchange the elastomeric
connector etc. before you
start working with the glue.
• Mount the phone as described in Mechanical Instructions 3/00021-1/FEA 209 544/21
(Reassembly).
3 Revision History
Rev. Date Changes / Comments
B 2000-03-10 Chapter 2 added
Trouble Shooting Guide, Mechanical
4/00021-1/FEA 209 544/21 C Approved according to 1776-1/FEA 209 544
Trouble Shooting Guide, Mechanical
Applicable for R320s and R320sc
Contents
1 Appearance Problems.....................................................................................................2
2 Network Problems...........................................................................................................3
3 On/Off Problems.............................................................................................................4
4 Audio Problems...............................................................................................................5
5 Display/Illumination Problems......................................................................................6
6 Capacity/Charging Problems.........................................................................................7
7 SIM Problems..................................................................................................................8
8 Key Problems...................................................................................................................9
9 Alert Problems...............................................................................................................10
10 Data Communication Problems...................................................................................11
11 Software Problems........................................................................................................12
12 Revision History............................................................................................................13
Trouble Shooting Guide, Mechanical
4/00021-1/FEA 209 544/21 C 2(13)
1 Appearance Problems
• Check the general condition of the system connector (Fig.1) and the battery connector (Fig.
2) for corrosion and oxidation.
• No action should be taken for a liquid damaged telephone. Send the unit on according to the
local company directives.
• Check that the antenna is not damaged and that it fits properly. (Fig.3).
• Check that the SIM holder is working correctly (Fig.4).
• Check if the battery fits correctly. Change the battery or send the unit on according to the
local company directives.
• Check the rear and the front covers for cracks and that both ends fit correctly (Fig.5). If
necessary replace the front cover according to the working instruction or send the unit on
according to the local company directives.
Fig.1 Fig.2 Fig.3
Fig. 4 Fig. 5
Trouble Shooting Guide, Mechanical
4/00021-1/FEA 209 544/21 C 3(13)
2 Network Problems
• Insert a fully functional SIM card and switch ON the telephone. Check that there is signal
strength shown in the display (Fig.1). If necessary replace the antenna according to the
working instructions.
• Check the antenna connector for dirt (Fig.2). If necessary clean it.
• Make a general visual inspection for oxidation or corrosion from liquid damage. No action
should be taken for a liquid damaged telephone. Send the unit on according to the local
company directives.
• If the fault still remains send the unit on according to the local company directives.
Fig. 1 Fig.2
Trouble Shooting Guide, Mechanical
4/00021-1/FEA 209 544/21 C 4(13)
3 On/Off Problems
• Check that the battery’s contact surface is free from dust/dirt and mechanical damage (Fig.
1). If necessary clean it.
• Check the battery connector pogo contact on the board for dirt/mechanical damage (Fig. 2).
If necessary clean it.
• Make a general visual inspection for oxidation or corrosion from liquid damage. No action
should be taken for a liquid damaged telephones. Send the unit on according to the local
company directives.
• Check the keyboard and the dome switch for malfunction (Fig. 3). If necessery, replace the
keybord according to the working instruktions or send the unit on according to the local
company directives.
• Change the battery.
• Try to upgrade the telephone with the latest software.
• If the fault still remains, send the unit on according to the local company directives.
Fig. 1 Fig .2 Fig .3
Trouble Shooting Guide, Mechanical
4/00021-1/FEA 209 544/21 C 5(13)
4 Audio Problems
• Call a network-connected telephone and check if it is the microphone or the loudspeaker
that causes the audio problem.
• Check the loudspeaker for dirt/mechanical damage (Fig.1). If necessary clean it or replace it
according to the working instructions.
• Check the loudspeaker spring contact on the board for dirt/mechanical damage (Fig. 2). If
necessary clean it.
• Check the microphone and microphone rubber for mechanical damage (Fig. 3). If necessary
replace them. Also check the microphone contacts, if they are damaged send the unit on
according to the local company directives.
• Check the system connector for dirt/mechanical damage (Fig.4). If necessary clean it.
• Make a general visual inspection for corrosion or oxidation from liquid damages. No action
is taken for liquid damaged telephone. Send the unit on according to the local company
directives.
• If the fault still remains send the unit on according to the local company directives.
Fig.1 Fig.2 Fig.3
Fig.4
Trouble Shooting Guide, Mechanical
4/00021-1/FEA 209 544/21 C 6(13)
5 Display/Illumination Problems
• Switch ON the telephone and check the display. If all the segments (characters) are missing,
check that the display contact surface on the board is free from dirt/ dust (Fig.1). If
necessary clean it. Check the display elastomer for dirt/mechanical damage (Fig 2). If
necessary replace it according to the working instructions. If the fault still remains, replace
the display according to the working instructions.
• If some of the segments (characters) are missing, or the contrast is bad, replace the display
according to the working instructions.
• Make a general visual inspection for oxidation or corrosion from liquid damage. No action
is taken for liquid damaged telephone. Send the unit on according to the local company
directives.
• If the fault still remains send the unit on according to the local company directives.
Fig.1 Fig.2
Trouble Shooting Guide, Mechanical
4/00021-1/FEA 209 544/21 C 7(13)
6 Capacity/Charging Problems
• Test the telephone with a new fullcharged battery. If necessary replace the battery.
• Check the battery’s condition and the battery’s contact surface for oxidation or corrosion
(Fig 1). If necessary replace the battery.
• Check the battery release button for dirt/mechanical damage and that the elasticity is good
(Fig 2). If necessary replace it according to the working instructions.
• Check that the battery connector is free form dirt/mechanical damage and that the battery
connector pins are elastic (Fig.3). If necessary clean it.
• Check the system connector for dirt/mechanical damage (Fig.4). If necessary clean it.
• Make a general visual inspection for oxidation or corrosion from liquid damages. No action
is taken for liquid damaged telephone. Send the unit on according to the local company
directives.
• If the fault still remains send the unit on according to the local company directives.
Fig.1 Fig.2 Fig.3
Fig.4
Autres manuels pour R320S
3
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Ericsson Téléphone portable
Ericsson
Ericsson A1228di Manuel utilisateur
Ericsson
Ericsson A1228ds Manuel utilisateur
Ericsson
Ericsson DT400 Manuel utilisateur
Ericsson
Ericsson A1228LX Manuel utilisateur
Ericsson
Ericsson A1018S Mode d’emploi
Ericsson
Ericsson T19LX Manuel utilisateur
Ericsson
Ericsson GA628 Manuel utilisateur
Ericsson
Ericsson SATELLITE R290 Manuel utilisateur
Ericsson
Ericsson R300d Manuel utilisateur
Ericsson
Ericsson EH 237 Manuel utilisateur
Ericsson
Ericsson T68 Guide de configuration
Ericsson
Ericsson R380 Mode d’emploi
Ericsson
Ericsson R380 Manuel utilisateur
Ericsson
Ericsson T60d Manuel utilisateur
Ericsson
Ericsson T39 Manuel utilisateur
Ericsson
Ericsson T29 Manuel utilisateur
Ericsson
Ericsson A1228d Manuel utilisateur
Ericsson
Ericsson A2618s Manuel utilisateur
Ericsson
Ericsson CF337 Manuel utilisateur
Ericsson
Ericsson T18LX Manuel utilisateur
