Ergoswiss ST 700A Manuel utilisateur

ASSEMBLY INSTRUCTIONS

for Screenlift ST 700A and 1000A

Art. Nr. 198.00156

Page 1/8

Edition: 11.2016

PARTS INCLUDED WITH YOUR SCREENLIFT

# 1 Screenlift ST 1000A / ST 700A

# 2 Lid lifter

# 3 Lift brackets

# 4 TV mounting brackets ( ST 1000A only)

# 5 R.F. Module

# 6 Remote control

# 7 AC input wire

# 8 Power supply bracket

# 9 Rocker switch

# 10 Power supply

ASSEMBLY INSTRUCTIONS

for Screenlift ST 700A and 1000A

Art. Nr. 198.00156

Page 2/8

Edition: 11.2016

CAUTION

Before you begin any of the Installation procedures, read and follow the warnings and safety

instructions. Only person that read these instructions are allowed to operate the Screen lift.

SAFETY INSTRUCTIONS

Use the following safety guidelines to help protect your lift from potential damage and to ensure your own

personal safety.

Read and follow all safety instructions

Read all the installation instructions before testing or installing your lift

Keep remote control out of reach of children

To prevent bodily injury keep hands and clothing away from the lift while it is in operation

Before installing the lift or working with it’s connections, unplug the lift from the electrical shock

If the Lift is mounted in furniture, please take care that no clamping borders and no danger of

squeezing can be generated. Please watch the CEE Directions for machine and make a risk analysis

Do not install the lift, power supply or R.F. module in places subject to extreme temperatures for

example near a radiator, or heating vent

To avoid damaging the power supply, R.F. module and power cord, do not put anything on it or

place it where it could become damaged

Unplug the lift in the following conditions:

oWhen the power cord or plug is damaged or frayed

oIf liquid has spilled into the lift, power supply or RF module

oIf the lift, power supply or RF module has been exposed to rain or water

oIf the lift exhibits a distinct change in performance, indicating a need for servicing

ASSEMBLY INSTRUCTIONS

for Screenlift ST 700A and 1000A

Art. Nr. 198.00156

Page 3/8

Edition: 11.2016

FUNCTION CONTROL

Remove all contents from packaging and compare with the listed parts. Test the function of the Screen lift

as follows: (refer to the sketch on page 1):

oConnect the cable of the Screen lift (# 2) to the control box (# 3)

oConnect the cable of the control box (# 3) to the power supply (# 4)

oConnect the cable of the rocker switch to the control box (# 3)

oConnect the net cable of the power supply (# 4)

oPut the Screen lift (# 2) in an vertical position

oPress the rocker switch, drive a few centimetres up and back again. The switch has to be pressed

always due of security reasons. By releasing the switch, the screen lift will stop immediately

oPress the remote control (+), drive a few centimetres up and back (-) again. The switch has to be

pressed always due of security reasons. By releasing the switch, the screen lift will stop immediately

PLEASE NOTE:

During the lifting process (up and down) the Screen lift has always been controlled by eye. If

there is a danger, the lift has to be stopped immediately.

MAIN MEASURES ST 100A

ASSEMBLY INSTRUCTIONS

for Screenlift ST 700A and 1000A

Art. Nr. 198.00156

Page 4/8

Edition: 11.2016

MAIN MEASURES, ST 700A

ASSEMBLY INSTRUCTIONS

for Screenlift ST 700A and 1000A

Art. Nr. 198.00156

Page 5/8

Edition: 11.2016

ASSEMBLY OF THE SCREENLIFT

oPlace the Screen lift (# 1) vertically (use a level) on the back panel of the cabinet in a location that

will allow full up and down movement of the TV. Use the intended fixing hole on the sides of the

Screen lift. The Screen lift has to be mounted about 4mm below the furniture border.

oAttach the power supply (# 10) with the power supply bracket (#8). Please follow the drawing on

page 1, the power supply needs to be mounted on the right side of the Screen lift.

oAttach the R.F. module (# 5) next to the power supply (# 10). Take care that the wires have enough

space that they cannot get caught.

oTo attach the Rocker Switch (# 9), you have to drill a hole at the designated position. Than press

the Rocker Switch in. Take care that the wires have enough space that they cannot get caught.

Attach the wires with cable clips.

oConnect the cable of the control box (# 3) to the power supply (# 10)

oConnect the cable of the rocker switch to the control box (# 5)

oConnect the net cable of the power supply (# 10)

oMove the TV mounting brackets (# 4) above the Lift brackets (# 3).

oAdjust the TV mounting brackets for your TV and attach it to the TV. Make sure the TV is attached

centrically to the mounting brackets.

oDrive the Screen lift (# 1) to its upper position.

oPlace the TV on wanted position and attach the lift brackets to the Screen lift.

oDrive down the Screen lift with the attacked TV. Take care that the TV cannot get jammed some-

where and that it breaks in completely to the furniture.

oAttach the Lid lifter (# 2) with the bended end to the direction of the front side into the groove of

the Screen lift. The Lid lifter has to stand over the TV.

oDrive again to the upper position an tight all screws.

Background for this direction is the characteristic of the assembly into a cabinet.

PLEASE TAKE CARE, THAT:

During operation, no hands and clothing can be kept in the function area of the Screen lift

No clamping borders and no danger of squeezing can be generated. Please watch the CEE

Directions for machine and make a risk analysis

ASSEMBLY INSTRUCTIONS

for Screenlift ST 700A and 1000A

Art. Nr. 198.00156

Page 6/8

Edition: 11.2016

USER INSTRUCION, RF REMOTE SYSTEM

INSTALLATION

oConnect the power supply and the motor unit to the remote receiver. Two different

plug sizes make this connection only possible to make it in the right way

oAfter having connected the plugs, the blue light will be light.

oPush the emitter buttons and the motor unit will move up and down.

oThe button has to be pushed while the Screen lift is operating.

LEARNING

oIf the remote receiver does not respond when pushing the emitter buttons, reset the

receiver. After that, code the emitter an receiver together again.

CODING

oPush the learner button on the receiver for less than 1 second

oPush one of the emitter buttons

oThe red light will start flashing

oPus one oft he emitter buttons again and the red light will turn off

oThe units now are ceded together with a unique code

RESET

oPush and hold down the learner button on the receiver for 10 seconds. (will be reset

when the red light turns off)

ASSEMBLY INSTRUCTIONS

for Screenlift ST 700A and 1000A

Art. Nr. 198.00156

Page 7/8

Edition: 11.2016

OPERATED BY ROCKER SWITCH

oBy pressing the switch upside the Screenlift will drive up

oBy pressing the switch downwards the Screenlift will drive down

The button has to be pressed during the whole lifting or lowering process due of security reasons. By

releasing the switch, the screen lift will stop immediately

PLEASE NOTE:

During operation (up and down) the Screen lift has always been controlled by eye. If there is

a danger, the lift has to be stopped immediately.

ADJUSTING THE STROKE LENGTH OF THE LIFT

Adjusting the bottom stop

The bottom stop can be adjusted to any prefferred height, e.g. if you do not want the lift to go all the way

down into the cabinet.

1. Remove the 2 covers

2. Use an allen key to loosen the screw of the wire

glider. Move the glider to the preferred

position and tighten the screw securely again.

3. Mount the 2 covers again.

ASSEMBLY INSTRUCTIONS

for Screenlift ST 700A and 1000A

Art. Nr. 198.00156

Page 8/8

Edition: 11.2016

Adjusting the top stop

The top stop can be adjusted to any preferred height, e.g. if you do not want the lift to go all the way out of

the cabinet.

Use an allen key to loosen the screw of the

wire glider. Move the glider to the preferred

position and tighten the screw securely again.

SALES ORGANISATION

Ergoswiss AG

Nöllenstrasse 15

9443 Widnau

Schweiz

T: 0041 71 727 06 70

F: 0041 71 727 06 79

M: info@ergoswiss.com

www.ergoswiss.com

The information in this document is subject to change without notice.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Ergoswiss Système de levage

Ergoswiss

Ergoswiss TQ-4 Manuel utilisateur

Ergoswiss

Ergoswiss TL-2 Manuel utilisateur

Ergoswiss

Ergoswiss SL 14 Compact Series Manuel utilisateur

Ergoswiss

Ergoswiss SLA 13 Series Manuel utilisateur

Ergoswiss

Ergoswiss SL 14 Compact Series Manuel utilisateur

Ergoswiss

Ergoswiss FC 650 3.0 Manuel utilisateur

Ergoswiss

Ergoswiss SL 13 Series Manuel utilisateur

Ergoswiss

Ergoswiss SL 13 Series Manuel utilisateur

Ergoswiss

Ergoswiss SLA 13 Series Manuel utilisateur

Ergoswiss

Ergoswiss TU-4 Manuel utilisateur

Ergoswiss

Ergoswiss SLA VD Series Manuel utilisateur

Ergoswiss

Ergoswiss PA 2830 Manuel utilisateur

Ergoswiss

Ergoswiss SL compact Manuel utilisateur

Ergoswiss

Ergoswiss TA-4 Manuel utilisateur

Ergoswiss

Ergoswiss SLA Manuel utilisateur

Manuels Système de levage populaires d'autres marques

morse

morse 82H-124 Manuel utilisateur

Braun

Braun NL955 Series Manuel utilisateur

haacon

haacon 1889.10 Manuel utilisateur

Protekt

Protekt AT 252 Manuel utilisateur

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Manuel utilisateur

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Manuel utilisateur

Genie

Genie Z-60/34 Manuel utilisateur

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Manuel utilisateur

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Manuel utilisateur

Custom Equipment

Custom Equipment Hy-Brid 3 Series Manuel de programmation

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Manuel de programmation

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Manuel de programmation

BERG

BERG BeNomic EasyLeaf Manuel utilisateur

Powermate

Powermate LiftGate LG-3 Manuel utilisateur

Snorkel

Snorkel TM12 Series Manuel utilisateur

Terberg

Terberg OMNIDEKA Manuel utilisateur

Harmar Mobility

Harmar Mobility AL625 Mode d'emploi

Rotary

Rotary SPO16 Manuel utilisateur