Ergochair Ergo-Jet Manuel utilisateur

Ergo-Jet™ Height-Adjustable WorkstaƟon Assembly and User Guide

P/N : 5900351 - Rev. A - June 2023

1645 Lemonwood Drive

Santa Paula, CA 93060 USA

(800) 253-2363 www.bendpak.com

The Ergo-Jet (5160112) is a fully height-adjustable workstaon providing increased mobility

on a stable ergonomic plaorm as you work. Gas springs support both the backrest and

the seat allowing a range of 15° to 60° of backrest adjustment and ≈8 inches of height

adjustment on the seat. Adjustable foot and arm rests as well as four 360° swivel casters

allow freedom of movement and comfort while working.

• Weight: 158.7 lbs. / 72 kg.

• Backrest and Seat Adjustment: Gas Spring

• Casters: Four 360° Casters (2 locking), Ø75 mm x

25 mm, sleeve bearings, oil resistant, non-marring

rubber wheels

• Seat Materials: Padded Marine Vinyl Backrest and

Seat. Marine Vinyl is abrasion, chemical and oil

resistant

• Tool/Parts Tray: Rugged steel tray for tools and

parts. 1.25 in. / 32 mm deep.

• Frame Materials: Full powder coated, welded

tubular steel

California ProposiƟon 65: This product can expose you to chemicals including styrene and vinyl chloride, which are on the list of over

900 chemicals idenﬁed by the State of California to cause cancer, birth defects, or other reproducve harm. Always use this product in

accordance with BendPak Ergochair’s instrucons. For more informaon, visit www.p65warnings.ca.gov.

Ergo - Jet SpeciﬁcaƟons:

agree that: you will give full aribuon to BendPak Inc., you will not make changes to the content, you do

not gain any rights to this content, and you will not use the copies for commercial purpose.

Ergo-Jet Product DescripƟon

Ergo-Jet Safety InformaƟon

• Please read this enƟre guide prior to use. Failure to follow the instrucons and safety precauons in this guide can result in serious

injury. By proceeding with setup and operaon, you agree that you fully understand the contents of this guide and assume full

responsibility for the use of this product. Always inspect the Ergo-Jet for loose or damaged components prior to each use. If a problem

exists resolve the issue. If the issue cannot be resolved, cease all use and contact your authorized Ergochair parts provider.

• Always be alert and aware of dangers around you while using this equipment.

• Only use the Ergo-Jet on hard, ﬂat surfaces.

• Always sit down on the Ergo-Jet gently. Avoid shock loads caused by jumping or falling onto the seat.

• Never stand on the Ergo-Jet or use it for a purpose for which it was not designed.

• Do not allow unsupervised children or persons to use this product.

• This product is not a toy. Never use as a skateboard or dolly.

• Beware of all pinch and crush hazards when adjusng the seat and backrest posion on this product, keep hands

and feet clear.

• Be aware that the Maximum Weight limit for the Ergo-Jet is 350 lbs. / 159 kg. Do not remove and hold Vehicle components that, when

combined with your own weight, exceed this maximum weight rang.

• Replace warning labels that are damaged or illegible.

• Do not operate your Ergo-Jet if you ﬁnd maintenance issues or it operates in an abnormal manner, take it out of service, then contact

BendPak Technical Support, email [email protected] or call (800) 253-2363 opon 7, then 4.

Assembly and User Guide

Guide P/N: 5900351 Rev. A- June 2023 A Length 35.25 in. (backrest up) to 47 in. (backrest down) /

894 mm (backrest up) to 1,194 mm (backrest down)

B Seat Width 14.8 in. / 376 mm

C Width 33.5 in. / 850 mm

D Arm Rest Width 24 in. to 29 in. / 610 mm to 737 mm

E Headrest Width 17.8 in. / 452 mm

F Arm Rest Height 27 in. to 36.5 in. / 686 mm to 927 mm

G Min. Backrest Angle ≈15°

H Backrest Angle max. ≈60°

I Foot Rest Height 8.5 in. to 11 in. / 216 to 279 mm

J Seat Height Range 18.75 to 26.75 in. / 476 to 679 mm

K Backrest Height 43.75 to 51.75 in. / 1,111 mm to 1,314 mm

L Ground Clearance 2.5 in. to 4 in. / 63.5 mm to 10 mm

Trademarks. Ergochair and the Ergochair logo, BendPak and the BendPak logo are registered trademarks of BendPak Inc. All other company,

product, and service names are used for idenﬁcaon only. All trademarks and registered trademarks menoned in this Manual are the

property of their respecve owners.

LimitaƟons. Every eﬀort has been made to ensure complete and accurate instrucons are included in this Guide. However, product updates,

revisions, and/or changes may have occurred since this Guide was published. BendPak reserves the right to change any informaon in this

Guide without incurring any obligaon for equipment previously or subsequently sold. BendPak is not responsible for typographical errors in

this Guide. You can always ﬁnd the latest version of the Assembly and User Guide for your product on the BendPak website.

Warranty. The BendPak warranty is more than a commitment to you: it is also a commitment to the value of your new product. Contact your

nearest BendPak dealer or visit www.bendpak.com/support/warranty for full warranty details.

Go to bendpak.com/support/register-your-product/ and ﬁll out the online form to register your product (be sure to click Submit).

Safety. Your Ergo-Jet was designed and manufactured with safety in mind. However, your safety also depends on proper training and

thoughul operaon. Do not install, operate, maintain, or repair the unit without reading and understanding this User Guide and the labels

on the unit; do not use the Ergo-Jet WorkstaƟon unless you can do so safely!

Assembly and User Guide

P/N 5900351 - Rev. A - June 2023

1645 Lemonwood Drive

Santa Paula, CA 93060 USA

(800) 253-2363 www.bendpak.com

Ergo-Jet™ Height-Adjustable WorkstaƟon

Item No. DescripƟon Qty.

1 Ergo-Jet Seat Assm. 1

2 Ergo-Jet Backrest 1

3 Ergo-Jet Arm Rest with Lockpins 2

4 Ergo-Jet Foot Rest 2

5 Swivel Casters 2

6 Locking Casters 2

7 Tool Tray 1

8 Backrest Spring Release Assembly 1

9 Gas Spring 2

10 HHB M6 x 12 (Tool Tray) 4

11 Nut M6 (Tool Tray) 4

12 HHB, M8 x 25 with Gas Spring 1

13 Nut, M8 with Gas Spring 1

14 SHCS, M8 x 20 (Casters) 16

15 M8 Washer, Flat (Casters) 16

16 Lock Washer, M8 Spring (Casters) 16

17 Nut, M8 (Casters) 16

18 SHCS M10 x 55 (Foot Rest) 2

19 Nut, M10 Nyloc (Foot Rest) 2

20 SHCS M12 x 55 (Foot Rest) 2

21 Nut, M12 Nyloc (Foot Rest) 2

22 HHB M14 x 50 2

23 Nut, M14 Nyloc 2

To Lower the Ergo-Jet Backrest:

1. Sit on the seat and lean against the backrest.

2. Pull the backrest spring release handle forward while pushing on the

backrest. The backrest should recline.

3. Release the handle when the backrest reaches the desired angle.

Parts List:

Ergo-Jet Assembly:

1. Open the box and remove the protecve packing foam.

2. Carefully cut the plasc and straps holding the backrest to the seat. Do NOT damage the foam seat or

backrest as you cut away the plasc.

3. Set the backrest aside where it will not be lost or damaged.

4. Remove the parts boxes. One box contains (4) casters, and the other box contains the fasteners bag,

(2) footrests with fasteners and lock pins. Set the components aside where they will not be lost or damaged.

5. Leave the seat on the shipping box. This will provide a clean ﬂat space to assemble the Ergo-Jet.

6. Verify all the components are present using the parts list.

7. Turn over the seat and aach the two locking casters to the front of the Ergo-Jet seat using four sets of SHCS

M8 x 20, ﬂat washers, lock washers, and hex nuts on each caster.

8. Aach the two swivel casters without locks to the rear of the Ergo-Jet seat using four sets of SHCS M8 x 20

with ﬂat washers, lock washers, and hex nuts on each caster.

9. Turn the Jet seat onto its casters and lock the front two casters to prevent unintended movement.

10. Retrieve the backrest and two M14 x 50 hex head bolts and M14 nyloc nuts.

11. Insert the backrest into the brackets on the back of the seat and secure with the hex head bolts and nyloc

nuts. Do not over-Ɵghten. The backrest must move freely between the pivot points created by the hex head

bolts.

12. Retrieve the spring release handle assembly. The spring release handle may be installed on either the right

or le-hand side of the seat.

13. Insert the spring release assembly into the square channel under and behind the seat. Push the spring

release through the square channel unl the threaded opening for the gas spring is visible in the middle

slot.

14. Thread the gas spring rod all the way into the spring release mechanism now visible through the middle slot.

15. Thread the lock nut and pad down the spring rod unl it contacts the spring release mechanism. Make

ﬁnger ght.

To Raise the Ergo-Jet Backrest:

1. Remove weight from the backrest.

2. Pull the backrest spring release handle forward. The backrest will rise.

3. Release the handle when the backrest reaches the desired angle.

To Lower the Ergo-Jet Seat:

1. Sit or push down on the Ergo-Jet seat.

2. Pull the seat spring release handle upward and push down on the seat.

3. Release the handle when the seat reaches the desired height.

To Raise the Ergo-Jet Seat:

1. Remove weight from the Ergo-Jet seat.

2. Pull the spring release handle upwards. The Jet seat will rise.

3. Release the handle when the seat reaches the desired height.

15. Retrieve the M8 x 25 hex head bolt and M8 nyloc nut.

16. Secure the top of the gas spring to the mounng bracket on the backrest.

17. Retrieve two footrests and two SHCS M10 x 55 with the M10 nyloc nuts, and

two M12 x 55 with the M12 nyloc nuts.

18. Mount the Footrests using the M12 and M10 fasteners. The footrests may be

mounted in the ﬂat or up posion.

Steps 7-9

Steps 10-11

Steps 12-16

Steps 17-18

Steps 19-21

Ergo-Jet Controls

19. Retrieve the two arm rests with lock pins.

20. Insert each arm rest into the arm weldment behind the seat and secure with

the lock pin.

21. Adjust the height and posion of the arm rests using the lock pins.

To clean the Ergo-Jet:

1. While Marine Vinyl is water, stain and

abrasion resistant, it is sll a porous

material. Wash the vinyl frequently

using soap and water.

2. Wipe the vinyl and the frame and then

dry aer cleaning.

3. If a more powerful cleaner is required,

use a small amount of dish soap and a

sobristle brush.

4. Rinse with water and wipe dry, then

allow to air dry fully.

5. Do not use bleach, vinegar, alcohol or

excessively harsh cleaners.

6. Store the Ergo-Jet in a clean, well

venlated, and dry area.

Manuels Ordinateur de bureau populaires d'autres marques

HP m9060n - Pavilion - Elite Fiche technique

Asus

Asus E210 Series Manuel utilisateur

Dell

Dell Inspiron 600m Manuel utilisateur

Dell

Dell Inspiron 3662 Manuel utilisateur

TotalFlow

TotalFlow uFLO Manuel utilisateur

HP Presario SV7000 - Desktop PC Manuel utilisateur

HP ProDesk 400 G5 Manuel

Logitech

Logitech MK320 Manuel utilisateur

Dell

Dell XPS 730 H2C Manuel utilisateur

Sony

Sony Vaio Series Manuel utilisateur

Sony

Sony VGC-LT32E - Vaio All-in-one Desktop Computer Manuel utilisateur

Alto

Alto MD 250 Manuel utilisateur

Lenovo

Lenovo ThinkCentre Edge 72 Manuel

Lenovo

Lenovo ThinkStation D20 Manuel

Arbor Technology

Arbor Technology FPC-7800 Series Manuel utilisateur

Sony

Sony VAIO VGX-TP1 Series Manuel utilisateur

Asus

Asus Eee Box B204 Manuel utilisateur

Dell

Dell Optiplex 9010 All In One Manuel utilisateur

ergochair Ergo-Jet Manuel utilisateur

Manuels Ordinateur de bureau populaires d'autres marques