ERA VALIANT Manuel utilisateur
INSTALLATION AND
OPERATING MANUAL
Version 1.0
VALIANT
Solar Siren Alarm Kit
ERA - VALIANT-Red Lens
DoP No: EM0017
IMPORTANT
PLEASE READ THIS MANUAL CAREFULLY BEFORE OPERATING
THE SYSTEM AND RETAIN FOR FUTURE REFERENCE.
All devices, with the exception of the external siren are suitable for mounting
in dry interior locations only.
Any repairs must be carried out by an Authorised Repair Centre. Misuse
or attempted repairs to a component part of the product will invalidate the
warranty. The photocopying, copying, reproduction, translation to any language,
modification, storage in a retrieval system or retransmission, in whole or in part,
in any form or by any means, electronic, mechanical or otherwise of this manual,
is strictly prohibited without the prior written permission of ERA Home Security.
Disposal and Recycling
Disposal of this product is covered by the Waste Electrical or Electronic Equipment
(WEEE) Directive. It should not be disposed of with other household or commercial
waste.
At the end of the product’s useful life, the packaging and product should be disposed
of via a suitable recycling centre. Please contact your local authority or the retailer
from where the product was purchased for information on available facilities.
Declaration of Performance
This equipment complies with the essential requirements of the Radio and
Telecommunications Terminal Equipment Directive, 1999/5/EC.
Additional Accessories
This can easily be extended at any time with the range of ERA Wireless Alarm
Accessories for details visit www.erahomesecurity.com or call our Customer
Support team on 0345 257 2500 (local call rate).
Page 1
Specifications
1.1 Get to know your product
1.2 LED Indication
1.3 PCB Layout
1.4 Test Mode
1.5 Working Mode
1.6 Installation
1. PIR Motion Detector
TABLE OF CONTENT
2.1 Get to know your product
2.2 PCB Layout
2.3 Installation
4.1 Positioning
4.2 PCB Layout
4.3 Jumper Setup
4.4 Usage
4.5 Installation
4.6 Jamming Detection
6. Notes 12
ERA Product Guarantee 13
5. Specification
4. Solar Charged Siren
3.1 Get to know your product
3.2 Buttons/Functions
2. Magnetic Door/Window Sensor
3. Remote Control
Kit Contents
3
3
3
3
4
4
4
4
5
5
6
6
7
7
7
8
8
8
8
9
10
10
11
Page 2
Wireless Solar Siren x 1
Door/Window Sensor x 1
PIR Motion Sensor x 1
Remote Control x 1
Batteries Included
1. Detection Window
2. Status Indicator
3. Test Button
4. Bracket Slot
5. Self-adhesive pad
fixing markers
Flashes every 2 seconds: Self-testing state
Flashing twice: Self testing finished, enters working mode
Flashes once: Movement is detected
Flashes once every 3 seconds: Low battery indication (immediate battery change required).
1.1. Get to know your product
KIT CONTENTS
1. PIR MOTION
DETECTOR
1
2
3
4
5
1.2. LED Indication
Page 3
To test in Working Mode, walk in front of the sensor, the LED should flash once when
movement is detected.
If the sensor is triggered twice in 3 minutes it will enter into power saving (sleep mode).
If no movement is detected within the next 3 minutes, the sensor will return to normal
working mode.
Remove the activation strip. Fit the retaining
screw supplied.
Self-testing will commence for 1 minute as
indicated by the LED flashing every 2 seconds.
To enter Test Mode press the test button at the
back of the PIR. The LEDs will then flash once
when movement is detected, for up to 3 minutes.
3.
2.
1.
2.
1.
Infrared Sensor: Detects movement and
triggers an alarm signal when the system
is armed.
Tamper Switch: If the casing is opened
when in ‘working state’, the tamper
switch will be triggered and generate an
alarm signal.
1.3. PCB Layout
1.5. Working Mode
1.4. Test Mode
AA 1.5V LR6
Infrared
Sensor
Zone
Setting
Tamper
Switch
Test
Button
Status
Indicator
AA 1.5V LR6
Avoid mounting the sensor in areas where draughts may be present or where the
temperature may fluctuate greatly, such as near to windows, air conditioning, heating,
refrigeration units, cooking appliances and direct sunlight.
1.6. Installation
1.
Page 4
2.1. Get to know your product
2. MAGNETIC DOOR/
WINDOW SENSOR
Fit the sensor in a position that will cover your desired protection area:
Fix the bracket to the wall with the fixings kit supplied. For optimum
performance set the height of the bracket to 2 metres above ground
level.
Adjust angle of the PIR sensor to cover the required detection area.
To perform a walk test.
Press the test button
once and walk from let
to right in the room.
The LED indicator will
flash once when motion
is detected.
2.
a.
b.
2m
Status Indicator
Magnet
Transmitter
Suitable for fitting to doors,
windows and any object that
opens and closes.
The Window/door sensor transmits
a signal to the control panel/siren
when ‘contact’ is broken between
the transmitter and the magnet.
Transmits a low battery signal to
the ERA alarm control panel.
Where possible, mount the sensor in the corner of the room so that the logical path
of an intruder would cut across the fan detection pattern. A PIR responds more
effectively to movement across the device that to movement directly towards it.
Page 5
Flashes once: Door/window opened,
transmitter sends the signal to the
control panel/ siren.
Flashes every 3 seconds: Low battery
indication (immediate battery change
recommended)
2.2. LED Indication PCB Layout
Carefully remove the activation strip
from the battery compartment.
Remove the backing paper from one side
of each self-adhesive double-sided strip.
Fix one strip to the back of the magnet
and one to the back of the transmitter.
Peel off the other side of each adhesive
strip. Mount the magnet on the door and
the transmitter on the door frame, with
less than a 1cm separation between the
two.
When opening the door a small red indicator
lights up briefly, this indicates that the
transmitter has sent a signal to the control
panel.
2.3. Installation
4.
3.
2.
1.
Tamper Switch
Battery
Zone Setting
Note: Please refer to the full system instructions for pairing a magnetic sensor.
Do not use the button on the back of the sensor to pair the sensor to the alarm as this
will put the sensor into 24hour mode.
Page 6
3.1. Get to know your product
3.2. Buttons/Functions
3. REMOTE
CONTROL
LED Indication
Arm
Part Arm
(Home Arm)
SOS Panic
Disarm
Flashes Once: Transmits the signal
Low Light Level: Low battery
indication, change the battery.
The remote control enables you to quickly and
conveniently arm and disarm your alarm system.
In the event of an emergency (when in or near
your property), pressing the SOS button will
trigger the an alarm on the control panel/siren.
Arm
Disarm
Part Arm
(Home Arm)
Panic Alarm
Mute Arm
Mute Disarm
Press to arm the control panel/siren and all of the accessories
(Full Arm)
Press to disarm the system
Press to part arm the alarm system (for systems with control
panels only)
Press to activate the panic alarm (SOS).
Press to arm the system with the solar siren in muted/silent
mode.
Press to disarm the system with the solar siren in mute/silent
mode.
Note:
1. For Mute Arm & Mute Disarm operation; press the home button for 1-2 seconds, then press the
Arm or Disarm button for a further 1-2 seconds.
2. The Mute Arm/Disarm will only be performed once before returning to sound. So the Mute
Arm/Disarm process would have to be done each time it is required.
3. By default arm/disarm is with sound. Page 7
Siren Duration Setting
Volume Setting Power On/Off
Inner Tamper Switch
Learn Button
Status LED Indicator
Alarm LED Indicators
Rear Cover
Tamper Socket
9V
Start-up
Battery
Rechargeable 3.7V
1800mAh Lithium Battery
4. SOLAR CHARGED
SIREN
4.1. Positioning
4.2. PCB Layout
4.3. Jumper Setup
Install the Siren to the outside of the building in a position that is clearly visible and at a
height which is relatively inaccessible to an intruder.
The Siren is designed to work on any aspect wall, however for optimum performance try
to avoid installing on a north facing wall or to a wall with shadows cast by other buildings,
trees and roof overhangs.
For optimum radio signal reception mount the Solar Siren to Maximum distance of one
metre from any external or internal metalwork (drainpipes, gutters, radiators, etc).
Rear
Anti-tamper
Switch
Sirens
(Default)
High
Mute
Low
High
Mute
Low
5Min
2Min
30s
5Min
2Min
30s
High
Mute
Low
5Min
2Min
30s
Siren Duration
Setting
Volume
Setting (Default)
Page 8
Table des matières
Autres manuels ERA Système de sécurité
ERA
ERA E2 Manuel utilisateur
ERA
ERA Protect Replica Siren Manuel utilisateur
ERA
ERA miGuard A105 Manuel utilisateur
ERA
ERA SOS100 Manuel utilisateur
ERA
ERA WIRELESS HD CCTV SYSTEM Manuel utilisateur
ERA
ERA ADDMORE WS280 Manuel utilisateur
ERA
ERA Invincible Manuel utilisateur
ERA
ERA Nu Mail Shield TS008 Manuel utilisateur
ERA
ERA Protect SALAPWHESSU Manuel utilisateur
ERA
ERA Protect Manuel utilisateur
Manuels Système de sécurité populaires d'autres marques
EDM
EDM Solution 6+6 Wireless-AE Manuel utilisateur
Highway Safety Group
Highway Safety Group EA401 Manuel utilisateur
Siren
Siren LED GSM Manuel utilisateur
Detection Systems
Detection Systems 7090i Instructions de montage
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuel utilisateur
Siemens
Siemens FDM273 Manuel utilisateur