Epson C831 Manuel utilisateur

USER MANUAL

Longitudinal Label Slitter

for EPSON C831

this product is certified:

INSTALLATION

STEP 1

Assemble the printer plate.

STEP 2

Connect the slitter to the printer plate.

STEP 3

Load the cardboard cores onto the core

holder.

STEP 4

Place the core holder in position. The

grey handle must match with the grey

holder.

Label Unwinder

(optional)

Paper Path

Waste

from

printer

Finished roll

STEP 5

Attach the labels to the cores.

This will provide the necessary tension

in order start the slitting process.

STEP 6

Align the blades with the edges and the

center of the labels, tighten the thumb

screw once the blade is in position.

You can alternate the position of the

thumb screws for easier access.

WARNING: The slitter blades are exposed and are VERY

sharp when the slitter station is in the “up” position. Use

extreme caution!

Label face out

Label face in

Slitter module has 3 positions:

- Upper position (A), the blades are closed to allow the media loading;

- Middle position (B), align the blades with the edges and the center of the labels, tighten the

thumb screw once the blade is in position;

- Lower position (C), the blade cut the media.

OPEN CLOSE

B C

The black knobs lock the slitter module

in the requested position.

Screw the thumb knobs to move the

blades to the right or to the left.

STEP 7

Switch on the Slitter.

Slowly turn the speed knob. Run the

slitter until the labels reach the bottom

of the take-up core holder.

Remove the labels that have rewinded

onto the take-up core holder.

STEP 8

Attach the labels to the core using a

waste label or tape.

Switch on the slitter and slowly turn to

increase the speed.

Now you can start to print.

HOW TO ADD OR REMOVE A BLADE HOLDER

Keep out the iron slide bar unscrewing the

thumb screw.

Slide in or out the blade holder.

Relocate the slide iron bar in its position

and rescrew the thumb screw.

REPLACING SLITTER BLADES

Loosen the two screws holding the blade in

place.

Replace the blade.

Fix back the screw to holding the blade in

place.

REWINDER GUIDES ALIGNMENT

Metal glides adjustable to obtain rolls of

labels perfectly aligned.

ULTRASONIC SENSOR CALIBRATION

WARNING: Before proceeding with the ultrasonic sensor

calibration, turn “OFF” the module that needs to be calibrated

(laminating or matrix removing).

1. Take a paper clip and insert it into the little hole located next to the OFF-ON

switch and push it down for 5 seconds. The yellow led will light up.

2. Raise the tension arm. The yellow led will stay on.

3. Once again, insert the paper clip down into the hole for 5 seconds. The led will

light o󰀨.

Ultrasonic sensor calibration complete.

LAMINATION / MATRIX REMOVER & SLITTER MODULES SPEED ROTATION

MATRIX REMOVER & SLITTER MODULE

WARNING: If what (pictured above) is not happening, please

press the button on circuit board untill the yellow led ashes.

After it ashes for 5 times release the button and perform a

new test.

ULTRASONIC TENSION CONTROLLER

smart solutions for the labeling industry

Label rewinder, label unwinder, electronic label dispenser and more...

- FOR MORE INFO CONTACT YOUR RESELLER -

Table des matières

Autres manuels Epson Accessoires pour imprimantes

Epson

Epson T545500 Instructions d'utilisation et d'entretien

Epson

Epson Stylus Color C80 Manuel utilisateur

Epson

Epson T079620 Manuel d'utilisation

Epson

Epson T6243 Manuel d'utilisation

Epson

Epson TX800-12H Manuel utilisateur

Epson

Epson T016201 Manuel d'utilisation

Epson

Epson T048120 Manuel d'utilisation

Epson

Epson T580300 Instructions d'utilisation et d'entretien

Epson

Epson T565300 Instructions d'utilisation et d'entretien

Epson

Epson T580600 Instructions d'utilisation et d'entretien

Epson

Epson T096220 Instructions d'utilisation et d'entretien

Epson

Epson T6248 Manuel d'utilisation

Epson

Epson T563300 Instructions d'utilisation et d'entretien

Epson

Epson T543800 Instructions d'utilisation et d'entretien

Epson

Epson T048520 Manuel d'utilisation

Epson

Epson T001011 Manuel d'utilisation

Epson

Epson 212MTBWPX-4.9 Manuel utilisateur

Epson

Epson Stylus Photo R210 Manuel d'utilisation et d'entretien

Epson

Epson T567800 Instructions d'utilisation et d'entretien

Epson

Epson S050192 Manuel d'utilisation

Epson

Epson T564200 Instructions d'utilisation et d'entretien

Epson

Epson LW-C610 Manuel utilisateur

Epson

Epson PJMB100 Instructions d'utilisation et de sécurité

Epson

Epson T544300 Instructions d'utilisation et d'entretien

Manuels Accessoires pour imprimantes populaires d'autres marques

Star Micronics

Star Micronics TSP800 Series Manuel utilisateur

REA

REA JET HR pro 2K Manuel utilisateur

HP Laserjet,Color Laserjet 4si Manuel utilisateur

oliser

oliser MS 45 Manuel utilisateur

Roland

Roland DU2-64 Instructions et recettes

Xerox

Xerox EFI EXP6000 Manuel utilisateur

Canon

Canon Finisher-T1 Manuel utilisateur

Sharp

Sharp FO-1MK Manuel utilisateur

Labelmate

Labelmate PM-300 Manuel utilisateur

Canon

Canon TonerRobot EP-27 Manuel utilisateur

Ricoh

Ricoh LCIT RT5100 Guide de démarrage rapide

GBC

GBC 16 Series Manuel utilisateur

Canon

Canon INNER 2-WAY TRAY-E1 Manuel d'utilisation et d'entretien

Develop

Develop SD-509 Manuel utilisateur

Kyocera

Kyocera KM-6230 Manuel

Triumph Adler

Triumph Adler DF-710 Manuel

Citizen

Citizen CBM-202PC Series Manuel utilisateur

Canon

Canon Color imageCLASS MF8170c Manuel utilisateur