Enware FHS011 Instructions de montage

Call 1300 369 273

www.enware.com.au

Enware Australia Pty Limited

9 Endeavour Rd Caringbah NSW 2229 Australia

Ph: +61 2 8556 4000 Fax: +61 2 8556 4055

I00063_Nov 17

FOOD SERVICE PRE-RINSE ASSEMBLIES

Installation, Operating & Maintenance Instructions

1 Call 1300 369 273 www.enware.com.au

page

PRODUCT CODES 3

TECHNICAL DATA 4

INSTALLATION COMPLIANCE 4

ASSEMBLY & INSTALLATION

Installing the base 5

Hob mounted single inlet FS011

FS010

Hob mounted twinner body FS015 7

Hob mounted exposed

breech

FS012 8

Hob mounted concealed

adjustable breech

FS013 9

Wall mounted exposed

breech

FS022 11

Wall mounted single inlet FS021

FS020

Wall mounted recessed

(concealed in wall)

FS023 13

Installing the riser, pot ller & spray arm 15

WATER CONNECTIONS 17

OPERATING INSTRUCTIONS 18

CLEANING 18

SERVICE AND MAINTENANCE 20

SPARE PARTS 20

TROUBLESHOOTING 21

PRODUCT WARRANTY FOR AUSTRALIA 22

contents

www.enware.com.au Call 1300 369 273 2

TROUBLESHOOTING

Thank you for choosing Enware’s Food Service Tapware . Designed and manufactured in Australia, the

Food Service Range is built using premium quality hose, brass and stainless steel to provide maximum

strength and durability. It can quickly and efficiently remove waste material from plates, pans and utensils

prior to them being washed.

Designed and manufactured in Australia

Built tough for the demands of busy commercial

kitchens where performance and reliability are

crucial

Proven durability in some of Australia’s leading

restaurants and fast food stores

Easy to use, ergonomically designed spray-trigger

and tap handles

Self-closing trigger spray turns off water when

not in use

Trigger spray achieves 6-Star WELS Rating with

efficient high velocity spray

Quarter turn jumper valve used in conjunction

with lever handles allow for easy control of water

flow

High water efficiency, reducing water costs

and energy costs for heating water

Integral dual check valve aid in backflow

prevention and protect the water supply from

contamination

Spring return allows spray and hose to be pulled

down into the spraying position, and then retract

back to upright position when released, reducing

back flow risk from the trigger spray being

immersed in water

Adjustable wall bracket provides increased

support and stability to the riser assembly

Modular design allows easy configuration to suit

specific needs

Fast, easy installation, supplied with minimal

on-site assembly required

food service pre-rinse assemblies

product features

3 Call 1300 369 273 www.enware.com.au

FHS001 FHS011 FHS021 FHS031

FHS041 FHS101 FHS111 FHS121

FHS131 FHS141 FHA016 FHA116

FS760

FWS001 FWS011 FWS021 FWS031

FWS101 FWS111 FWS121 FWS121C

FWS121W FWS131 FS704 FS705

FSJ705 FWA016 FWA056 FWA116

FWA156

Hob

Mounted

Wall

Mounted

product codes

www.enware.com.au Call 1300 369 273 4

technical data

Water Inlet Connecon (Hot / cold)

1/2” BSP (DN 15mm)

5/8” BSP (In-wall recessed SBA)

Working Pressure Range

10-1200 kPa (Jumper valve, spring loaded valve)

50-800 kPa (Ceramic Disc)

Recommended Working Pressure Range* 150-500 kPa max*

Flow Rate Pre-rinse spray gun 4 L/min

Pot ller 8 L/min. supplied standard

Operang Temperature Range

0 - 95 °C (Jumper valve)

0 - 85 °C (Spring loaded valve, incl. pre-rinse spray gun)

0 - 75 °C (Ceramic Disk)

WATER SERVICES

Plumbing Code of Australia: Part B1 Cold Water

Services AS / NZS 3500.1-2003 Water Services;

• Secon 1.6(a) Facilies for people with Disabilies

• Secon 3.3.2 Pressure at outlets (min 50kPa)

• Secon 3.3.4 Maximum pressure within

buildings (500kPa stac)

• Secon 3.4 Velocity Requirement (Max 3.0m/s)

• Secon 16 Tesng and Commissioning; Flushing,

Hydrostac tesng, cleaning and disinfecon of

water services.

HEATED WATER SERVICES

Plumbing Code of Australia: Part B2 Heated Water

Services

AS / NZS 3500.4-2003 Heated Water Services;

• Secon 1.9 Water Temperature

1.9.1 Storage Temperature

1.9.2 Sanitary xtures delivery temperature

1.9.3 Acceptable soluons for control of delivery

temperatures

• Secon 10 Heated Water Services for People

with Disabilies

• Secon 11 Tesng and Commissioning

installation compliance

*Enware products are to be installed in accordance with the Plumbing Code of Australia (PCA), AS/NZS3500

and the manufacturer’s instrucons.

Installaons not complying with PCA, AS/NZS 3500 or the manufacturer’s instrucons may void the product

and performance warranty provisions.

This product must be installed and commissioned by a qualied plumber. The following clauses must be

observed for a compliant installaon and correct operaon of Enware tapware.

For use with potable water only.

5 Call 1300 369 273 www.enware.com.au



• Ensure all operang and dimensional specicaons

are suitable for the intended installaon.

• Check that there is no shelf or obstrucon above.

Shorter riser, hose & spring guard opons are

available from Enware

• Check that wall bracket can be installed on a stable

wall surface. If not, extra measures may need to be

taken so that the bracket can be supported by a rm

wall backing.

•       

to remove debris prior to the installaon of this

product as per AS/NZS 3500.1. Strainers (40 mesh)

are recommended if debris is an ongoing problem.

• Ensure water pressures for hot and cold supplies

   If not, one side may

override the other. A pressure reducon valve

may be required to address any imbalance in

the water supply pressure, or to comply with the

recommended maximum pressure.

• It is recommended that isolaon valves are installed

on both hot and cold supplies prior to the pre-rinse

unit and that these are easily accessible.

Choose the type of base to be installed.

Unpack and layout all components to check that you have all parts.

Hob Mounted

Single Inlet

[FS011, FS010]

Wall Mounted Exposed

Breech [FS022]

Wall Mounted Single Inlet

[FS021, FS020]

Wall Mounted Recessed

(Concealed In-Wall) [FS023]

Hob Mounted

Twinner Body

[FS015]

Hob Mounted Exposed

Breech [FS012]

Hob Mounted

Concealed Breech

[FS013]

assembly and installation procedure

installation the base

GO TO PAGE 6

GO TO PAGE 11

GO TO PAGE 7 GO TO PAGE 8

GO TO PAGE 12

GO TO PAGE 9

GO TO PAGE 13

www.enware.com.au Call 1300 369 273 6

1. Fit 1/2” Tail into Base Mount:

Apply thread sealing tape onto the

non-beveled end of 1/2” BSP all-thread tail,

and screw to female thread of hob base.

2. Mark the hole to be drilled on the bench

(min. 40mm - max. 160mm to the centre

from wall) and drill the hole (Φ 22mm) using

a hole saw or similar tool.

3. For tap base with an-rotaon pins,

note the orientaon of the tap handle

(standard is either facing the front or to the

right hand side). Check the posions of the

two an-rotaon pins on the underside of

base. Mark the corresponding pin locaons

onto bench and drill 2x holes (Φ 9mm).

4. Fit base onto the bench and secure using

1/2” brass nut from underneath the bench.

For base with an-rotaon pins, t black

spacer rst (if required), then t the nut,

and ghten rmly. Do not over-ghten.

(Using excessive force may result in damage

to the black plasc spacer.) SEE IMAGE 5.

5. Proceed to installaon of riser, pot ller &

spray arm – page 15

IMAGE 1

IMAGE 4

IMAGE 2

Single inlet hob tap

assembly - Maximum

bench thickness: 35mm

Hob base mount -

Maximum bench

thickness: 10mm

33 mm

40 mm MIN -

160 mm MAX

WALL

IMAGE 3

IMAGE 5

hob mounted single inlet FS011 FS010

7 Call 1300 369 273 www.enware.com.au

1. Mark the hole to be drilled on the bench

(min. 40mm - max. 160mm to the centre

from wall) and drill a Φ33mm hole using a

hole saw or similar tool.

2. Unscrew metal washer and xing nut from

body assembly.

Fit one exible inlet hose onto body. Apply

a small amount of food grade grease onto

o-ring before ng. (Note markings on

exible hose – red [for hot] and blue [for

cold])

3. Fit base onto bench through the drilled

hole. From underneath the bench, t large

metal washer before ng the brass locking

nut. Hand-ghten locking nut. Check that

tap base is facing straight forward, then use

a Philips head screw driver to rmly ghten

the two screws on either sides of brass nut.

4. Fit the other exible inlet hose onto body.

5. Proceed to installaon of riser, pot ller &

spray arm – page 15

IMAGE 7

40 mm MIN -

160 mm MAX

WALL

IMAGE 6

IMAGE 8

IMAGE 10

IMAGE 9

Maximum bench

thickness: 30mm

hob mounted twinner body FS015

www.enware.com.au Call 1300 369 273 8

1. Mark 2x holes to be drilled on the bench.

(min. 40mm - max. 160mm to the centre

from wall, 215mm apart, or for adjustable

width models - min. 150mm, max. 330mm)

2. Drill the holes (Φ 22mm) using a hole saw or

similar tool.

3. Ensure the base cover domes and clear

washers are ed, and x base body onto

bench. From underneath the bench, t lock

nuts onto the tails and ghten rmly using a

spanner.

4. Proceed to installaon of riser, pot ller &

spray arm – page 15

IMAGE 12

215 mm

40 mm MIN -

160 mm MAX

WALL

(Adjustable Models:180 mm MIN - 330 mm MAX)

IMAGE 11

Maximum bench

thickness: 30mm

hob mounted exposed breech FS012

9 Call 1300 369 273 www.enware.com.au

1. Mark the holes to be drilled on the bench

and drill the holes. (min. 40mm - max.

160mm to the centre from wall, tap body

centres min. 150 mm – max. 300mm. Drill

hole size: spout – Φ 22mm, tap bodies – Φ

33mm).

Cut the copper T piece to size:

2. Screw 1x brass xing nut on each tap body

and screw the nut right down to the end of

thread.

3. Fit the bodies upside down into the 33mm

holes from top of the bench. Align centre

of the copper T piece to the centre hole.

Mark the copper pipes on both sides.

(19mm past the end of the body thread,

or deduct 15mm from the centre of drilled

hole on each side). Check the measurement

again, and cut the copper tube with

tube cuers. De-burr the copper tube.

Take tap bodies out of the holes and keep

at hand.

Fit the spout:

4. Pull the brass 1/2” threaded tail o the

copper T-piece. Apply thread sealant to the

non-beveled end of the 1/2” threaded tail,

then screw into the base of the swivel hob

and ghten.

5. Fit smaller clear washer through the 1/2”

tail, then t the base onto the bench. From

underneath the bench, t smaller red bre

washer onto the tail, then screw 1/2” brass

nut on. Note the orientaon of the grub

screw on the base, then ghten the brass

nut rmly using a spanner. SEE IMAGE 17

IMAGE 14 IMAGE 15

IMAGE 16

150 mm MIN - 300 mm MAX

40 mm MIN -

160 mm MAX

WALL

IMAGE 13

IMAGE 17

Maximum bench

thickness: 20mm

hob mounted concealed adjustable breech FS013

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels enware Équipements de cuisine et de salle de bain

enware

enware DET5072A-CNBSN Manuel utilisateur

enware

enware WELLBEING Series Instructions d'installation et d'utilisation

Manuels Équipements de cuisine et de salle de bain populaires d'autres marques

Grohe

Grohe BRIDGEFORD 33 870 Manuel utilisateur

Hans Grohe

Hans Grohe Zenio Metro 31811000 Manuel utilisateur

Gröne

Gröne Zedra 32 555 Manuel utilisateur

Transform

Transform QL045 Manuel utilisateur

Sanela

Sanela SLU 09PTB Manuel utilisateur

Glacier bay

Glacier bay FP4A0052BNV Instructions de montage

Lefroy Brooks

Lefroy Brooks C1-1400 Instructions de montage

Grohe

Grohe Rapido E Manuel utilisateur

Danze

Danze D302455 Manuel utilisateur

Waterworks

Waterworks CEKM30 Feuille d'instructions

Helvex

Helvex Omega TV-298 Manuel utilisateur

Tribata.

Tribata. GEORGIAN G5393 Manuel utilisateur

Alpha Bidet

Alpha Bidet Alpha One Manuel utilisateur

InSinkErator

InSinkErator H/HC3300 Manuel d'installation

Clou

Clou Xo type 1 Manuel utilisateur

Kohler

Kohler Contra 26448T-4 Manuel utilisateur

Grohe

Grohe Bridgeford 20 158 Manuel utilisateur

Hans Grohe

Hans Grohe Croma Select S 180 Showerpipe EcoSmart... Manuel utilisateur

enware FHS011 Instructions de montage

Manuels Équipements de cuisine et de salle de bain populaires d'autres marques