Enviro EF-V EVOLUTION Manuel utilisateur

SHERWOOD INDUSTRIES LTD.

6782 OLDFIELD RD

VICTORIA, BRITISH COLUMBIA V8M-2A3

PELLET STOVE

EF-V EVOLUTION

OWNERS TECHNICAL MANUAL

ENVIROFIRE INSTALLATION MANUAL

TABLE OF CONTENTS

1) INTRODUCTION PAGE

Pellet Quality ........................................................................ 3

Important Safety Data........................................................... 4

Warnings and Recommendations......................................... 5

Automatic Safety Features ................................................... 5

Deciding Where To Locating Your Pellet Appliance ............. 6

Fireplace Dimensions ........................................................... 6

Removing Your New Stove From It’s Pallet.......................... 7

Pedestal Installation ............................................................. 7

4) INSTALLATION

Vent Termination Requirements ........................................... 8

Clearances to Combustibles................................................. 9

Mobile Home Installation .................................................... 10

Outside Fresh Air Connections........................................... 10

Horizontal Exhaust through the Wall ............................. 11-12

Inside Vertical Pipe Installation........................................... 13

Hearth Mount Installation.................................................... 14

Exterior Mounted Exhaust Blower ................................. 15-18

2) OPERATION

How to Start Your Pellet Appliance..................................... 19

Turning Your Pellet Appliance Off ...................................... 19

Slider/Damper..................................................................... 20

3) SPECIFICATIONS / MAINTENANCE

Areas for Routine Maintenance ..................................... 21-22

Electrical Component Functions .................................... 23-25

5) SERVICE

Troubleshooting............................................................. 26-29

Wiring Diagram................................................................... 30

Parts List ............................................................................ 31

Exploded views.............................................................. 32-33

Warranty............................................................................. 34

PELLET QUALITY IS IMPORTANT, PLEASE READ THE

FOLLOWING PAGE

Your pellet stove has been designed to burn wood pellets only. Since there are many manufacturers of

wood pellets it is important to select pellets that are free of dirt or any impurities. The Pellet Fuel

Industries (P.F.I.) has established standards for wood pellet manufactures. We recommend the use of

pellets that meet or exceed these standards. Ask your dealer for a recommended pellet type.

THE PERFORMANCE OF YOUR PELLET STOVE IS GREATLY AFFECTED BY THE TYPE AND

QUALITY OF WOOD PELLETS BEING BURNED. AS THE HEAT OUTPUT OF VARIOUS QUALITY

WOOD PELLETS DIFFER, SO WILL THE PERFORMANCE AND HEAT OUTPUT OF THE PELLET

STOVE.

Since Sherwood Industries Ltd. has no control over the quality of pellets that you use, we assume no

liability caused by the quality of wood pellets used.

P.F.I. PELLET STANDARDS:

Fines .....................................1% maximum through a 1/8” screen

Bulk Density ..........................40 lbs. per cubic foot minimum

Size .......................................1/4” to 3/8” diameter 1 – 1.5” long maximum

Ash Content ..........................1% maximum

Moisture Content...................8% maximum

Heat Content .........................approximately 8200 Btu per lb. minimum

Check the burn-pot liner periodically to ensure that the holes are not blocked with clinkers, (clinkers are

silica in the fuel that will form a hard mass during the burning process). If they are blocked, remove the

liner (when the unit is cold) and clean the clinkers out. The liner should be cleaned or scraped once

every 2-3 days depending on wood pellet quality. Clean the holes in the lines with a small pointed

object.

Store pellets at least 36” (1 m) away from the pellet stove.

IMPORTANT SAFETY DATA

To prevent the possibility of a fire, ensure that the appliance is properly installed by adhering to the

installation instructions. An ENVIROFIRE dealer will be happy to assist you in obtaining information

with regards to your local building codes and installation restrictions.

The stove’s exhaust system works with negative combustion chamber pressure and a slightly positive

chimney pressure, it is very important to ensure that the exhaust system be sealed and airtight.

This unit is designed to burn pelletized wood fuel only. Do not use any other type of fuel, this will void

any warranties stated in this manual.

THE USE OF CORDWOOD IS PROHIBITED BY LAW.

Do not burn with insufficient combustion air. A periodic check is recommended to ensure proper

combustion air is admitted to the combustion chamber. Setting the proper combustion air is achieved

by adjusting the slide damper located on the left side of the stove.

It is advisable to clean the exhaust vent bi-annually or every two tons of pellets.

The grounded electrical cord should be connected to a standard 115 volts, 60-hertz electrical outlet. Be

careful that the electrical cord is not trapped under the appliance and that it is clear of any hot surfaces

or sharp edges. This unit’s maximum power requirement is 470 watts (3.91amps) for the EF-V

EVOLUTION.

Minor soot or creosote may accumulate when the stove is operated under incorrect conditions such as

an extremely rich burn (black tipped, lazy orange flames).

When installing the stove in a mobile home, it must be electrically grounded to the steel chassis of the

home and bolted to the floor. Make sure that the structural integrity of the home is maintained.

Be sure to maintain the structural integrity of home when passing a vent through walls, ceilings, or

roofs.

The ash pan must be locked securely for proper and safe operation of the pellet stove.

If you have any questions with regards to your stove or the above-mentioned information, please feel

free to contact your local dealer for further clarification and comments.

Since Sherwood Industries Ltd. has no control over the installation of your stove, we grant no warranty

implied or stated for the installation or maintenance of your stove, therefore, Sherwood Industries Ltd.

assumes no responsibility for any consequential damage.

SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

WARNINGS AND RECOMMENDATIONS

A. Do not abuse the glass by striking or slamming the door shut.

B. Do not attempt to operate the stove with broken glass.

C. Do not attempt to open the door and clean the glass while the unit is in operation. To clean the

glass, use a soft cotton cloth and mild window cleaner, gas or wood stove glass cleaner or take

a damp paper towel and dip into the fly ash, this is a very mild abrasive and will not damage the

glass.

D. Do not use abrasive cleaners to clean the surface or any part of the stove.

E. It is recommended that the unit be secured into its position in order to avoid any displacement.

F. Never use gasoline, gasoline-type lantern fuel, kerosene, or similar liquids to start the fire. Keep

all such liquids well away from the pellet stove while it is in use.

G. Disposed ashes should be placed in a metal container with a tight fitting lid. The closed

container of ashes should be on a non-combustible floor on the ground, well away from all

combustible materials pending final disposal. The ashes should be retained in the closed

container until all cinders have thoroughly cooled before disposing of them.

H. Make sure the ash pan is closed tightly during the operation of the stove.

I. KEEP ASH PAN FREE OF RAW FUEL. DO NOT PLACE UNBURNED OR NEW PELLET

FUEL IN ASH PAN. A fire in the ash pan could be the result.

J. Fresh air intake is strongly recommended. Failure to install Intake air may result in the unit

smoking during power failures as well as improper combustion.

NOTE: Fresh air is mandatory on all units installed in “Mobile Homes” as well as “Air

Tight” homes.

AUTOMATIC SAFETY FEATURES OF YOUR PELLET STOVE

A. The stove will shut off when the fire goes out and the exhaust temperature drops below 120°F

(49°C).

B. The stove has a high temperature safety switch. If the temperature on the hopper reaches

200°F (93°C) the auger will automatically stop, and the stove will shut down when the exhaust

temperature cools. If this happens call your local dealer to reset the 200°F (93°C) high limit

switch. ALSO FIND THE REASONS WHY THE UNIT OVERHEATED.

C. If the power goes out, the unit will stop running. When the power comes back on, the stove will

not restart unless the exhaust temperature is still above 120°F (49 °C).

DECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE

1. Check clearances to combustibles.

2. Do not obtain combustion air from an attic, garage or any unventilated space. Combustion air may be

obtained from a ventilated crawlspace.

3. Do not install the stove in a bedroom.

4. You can vent the stove through an exterior wall behind the unit or connect it to an existing masonry or

metal chimney (must be lined if the chimney is over 6” in diameter, or over 28 sq. inches cross sectional

area). An interior vent can be used with approved pipe passing through the ceiling and roof.

5. Locate the stove in a large and open room that is centrally located in the house. This will optimize heat

circulation.

6. The power cord is 8 feet (2.43 m) long and may require a grounded extension cord to reach the nearest

electrical outlet.

FIREPLACE DIMENSIONS

SIDE VIEWFRONT VIEW

TOP VIEW

UNIT DIMENSIONS

HEIGHT: 33.056 (83.96 CM)

WIDTH: 22.225 (56.45 CM)

DEPTH: 21.239 (53.94 CM)

HEARTH PAD:

WIDTH: 24.360 (61.87 CM)

DEPTH: 27.864 (70.77 CM)

REMOVING YOUR NEW STOVE FROM THE PALLET

To remove your new stove from its pallet, open the left and right side panels. There are two wood screws that are

holding the bottom of the stove to the pallet. Remove the screws. Close the side panels.

To remove the right and left hand cabinet sides there

are three T-20 Torx screws on the back of the panel,

loosen these screws only.

Remove the one screw located on the front of the

cabinet side located behind the top louvers.

Remove the two wood screws (one on either side of

the unit) to remove the unit from the pallet.

HEARTH PAD PEDESTAL INSTALLATION

Carefully place the back of the pellet appliance on the pallet and install the hearth pad. Align the holes in the

hearth pad and the unit and install the four screws provided.

Place the unit on its back and install the hearth pad using the four screws provided

This unit can be installed on a

combustible floor due to the built in

pedestal hearth pad, for example

linoleum, hardwood flooring. If this unit

is to install onto a carpeted surface a

hearth pad must be used for stability.

This unit is supplied with 4 leveling legs

for uneven surfaces. Adjust these

leveling legs until unit is level.

LEVELING LEGS

X 4

VENT TERMINATION REQUIREMENTS

1. Do not terminate the vent in any enclosed or semi-enclosed areas such as a carport, garage, attic,

crawlspace, narrow walkway, closely fenced area, under a sundeck or porch, or any location that can build up

a concentration of fumes such as stairwells, covered breezeway, etc.

2. Vent surfaces can become hot enough to cause burns if touched by children. Non-combustible shielding or

guards may be required.

3. Termination must exhaust above the inlet elevation. It is recommended that at least five feet of vertical pipe

be installed outside when the appliance is vented directly through a wall to create some natural draft to

prevent the possibility of smoke or odor during appliance shut down or power failure. To keep exhaust from

causing a nuisance or hazard from exposing people or shrubs to high temperatures. In any case, the safest

and preferred venting method is to extend the vent through the roof vertically.

4. Vent terminal cannot be:

less than 4 feet (1.2 m) below

less than 4 feet (1.2 m) horizontally from, and

less than 1 foot (305 mm) above

Doors, window openings, or gravity/ventilation air inlet into building:

5. Distance from bottom termination and grade –12” (305 mm) minimum.(including exterior exhaust blower) This

is conditional upon the plants and nature of grade surface. The exhaust gases are hot enough to ignite grass,

plants and shrubs located in the vicinity of termination. The grade surface must not be lawn. Distance from

bottom of termination and public walkways is 7 feet (2.1 m) minimum.

6. Distance to combustible materials is 2 feet (610 mm). This includes adjacent buildings, fences, protruding

parts of the structure, roof overhang, plants, shrubs, etc.

7. If the unit is incorrectly vented or the air to fuel mixture is out of balance, a slight discoloration of the exterior

of the house might occur. Since these factors are beyond Sherwood Industries LTD’s. control, we grant no

guarantee against such incidents.

IT IS RECOMMENDED THAT AN AUTHORIZED DEALER/INSTALLER INSTALL YOUR PELLET STOVE

NOTE: Measure clearance to the nearest edge of the exhaust hood

- MINIMUM 4 feet (1.2m) below or beside any door or window that opens.

B- MINIMUM 1 foot (305 mm) above any door or window that opens.

C- MINIMUM 2 feet (610 mm) from any adjacent buildings.

D- MINIMUM 7 feet (2.1 m) above grade when adjacent to public walkways.

(NOTE) Vent may not terminate in a covered walkway or breezeway.

E- MINIMUM 2 feet (610 mm) above plants, grass or other combustible

materials.

F- MINIMUM 3 feet (915 mm) from any forced air intake of other appliances.

G- MINIMUM 2 feet (610 mm) below any eave or roof overhangs.

H- MINIMUM 1 foot (305 mm) clearance to a combustible wall.

W- MINIMUM 2 feet

(

610 mm

)

above the roof.

Adjacent Wall

Back Wall

Side Wall

CLEARANCES TO COMBUSTIBLES

This unit can be installed on a combustible floor due to the built in pedestal hearth pad, for example linoleum,

hardwood flooring. If this unit is to install onto a carpeted surface a hearth pad must be used for stability.

SIDE WALL TO UNIT 6 INCHES (900 MM)

BACK WALL TO UNIT 2 INCHES ( 50 MM)

ADJACENT WALL 2 INCHES (50 MM)

ALCOVE CLEARANCES

This unit may be installed in an Alcove. Maintain these clearances to combustibles.

ALCOVE WIDTH 36 INCHES (900 MM)

ALCOVE HEIGHT 48 INCHES (1200 MM)

ALCOVE DEPTH 48 INCHES (1200 MM)

INSTALL VENT AT CLEARANCES SPECIFIED

BY THE VENTING MANUFACTURE.

EXHAUST AND FRESH AIR INTAKE DIMENSIONS

MOBILE HOME INSTALLATION

- Secure the heater to the floor using the two holes in the pedestal. Do not disturb the structural integrity of

the home.

- Ensure the unit is electrically grounded to the chassis of your home (permanently).

- Do not install in a room people sleep in.

- Outside fresh air is mandatory.

OUTSIDE FRESH AIR CONNECTIONS

Outside fresh air is mandatory when installing this unit in airtight homes and mobile homes. When

connecting to an outside fresh air source, do not use plastic, combustible pipe. Only 2” ID (inside diameter) steel,

aluminum or copper pipe should be used. It is recommended, when you are installing a fresh air system, to keep

the number of bends in the pipe to a minimum.

EXTERNAL MOUNTED EXHAUST BLOWER.

(A)

Base to center of flue 8.36 inches (21.34 CM)

Side to center of flue 8.16 inches (20.72 CM)

INTERIOR MOUNTED EXHAUST BLOWER.

(B)

Base to center of flue 10.71 inches (27.20 CM)

Side to center of flue 10.62 inches (26.97 CM)

FRESH AIR INTAKE.

Base to center of intake 8.47 inches (21.51 CM)

Side to center of intake 7.97 inches (20.54 CM)

(A)

(B)

Table des matières

Autres manuels Enviro Poêle à granulés

Enviro

Enviro P3 Manuel utilisateur

Enviro

Enviro Empress-A-FS Manuel utilisateur

Enviro

Enviro MERIDIAN Manuel utilisateur

Enviro

Enviro Milan Manuel utilisateur

Enviro

Enviro MERIDIAN-A Manuel utilisateur

Enviro

Enviro M55C-FPI Manuel utilisateur

Enviro

Enviro Mini 2 Manuel utilisateur

Enviro

Enviro Mini A Manuel utilisateur

Enviro

Enviro Meridian C-10135 Manuel utilisateur

Enviro

Enviro Empress-1 FS Manuel utilisateur

Enviro

Enviro Omega Manuel utilisateur

Enviro

Enviro MERIDIAN Manuel utilisateur

Enviro

Enviro Solus Manuel utilisateur

Enviro

Enviro Milan Manuel utilisateur

Enviro

Enviro EF-II I Manuel utilisateur

Enviro

Enviro Maxx-M Manuel utilisateur

Enviro

Enviro Omega Manuel utilisateur

Enviro

Enviro OLYMPIAN Manuel utilisateur

Enviro

Enviro Bern Manuel utilisateur

Enviro

Enviro Bern Manuel utilisateur

Enviro

Enviro EF-IV I Manuel utilisateur

Enviro

Enviro Evolution Manuel utilisateur

Enviro

Enviro WINDSOR 50-1578 Manuel utilisateur

Enviro

Enviro EP3 Manuel utilisateur

Manuels Poêle à granulés populaires d'autres marques

SMG

SMG Comfort Bilt HP50GC Manuel utilisateur

Quadra-Fire

Quadra-Fire MTVI-E2-MBK Manuel utilisateur

Quadra-Fire

Quadra-Fire MTV-E2-CSB Manuel utilisateur

Palazzetti

Palazzetti JP Series Guide d'installation

Travis Industries

Travis Industries Avalon 900 PS Manuel utilisateur

Flame

Flame FP-45 Manuel utilisateur

Astra

Astra P-7 Manuel utilisateur

Heatilator

Heatilator ECO-ADV-PS35 Manuel utilisateur

Cadel

Cadel aquos 24 h2O Manuel utilisateur

vicenza

vicenza V4.5 Manuel utilisateur

MCZ

MCZ VIVO 90 COMFORT AIR 9 M1 Manuel technique

Quadra-Fire

Quadra-Fire 1000 Gold Manuel du propriétaire

Ferroli

Ferroli GEMMA Manuel utilisateur

pleasant hearth

pleasant hearth PH35PS Series Manuel utilisateur

Breckwell

Breckwell Tradition P24FS Manuel utilisateur

Quadra-Fire

Quadra-Fire CB1200M-MBK Manuel utilisateur

England's Stove Works

England's Stove Works 25-EP Manuel utilisateur

Avalon

Avalon Astoria Manuel utilisateur