Entrya GS-500 Manuel utilisateur

GSM REMOTE CONTROL

GS-500

USER MANUAL

2EN Manual GS-500_EN_2014-01

User Manual v1.0

SAFETY INSTRUCTIONS

Please read and follow these safety guidelines to safeguard yourself and others:

• GSM switch-gate controller GS-500 (later referred to as “the system” or “ the device”) contains a built-in radio transceiver operating in

GSM 850/900/1800/1900 MHz bands.

• DO NOT use the system where it can cause potential danger and interfere with other devices – such as medical devices.

• DO NOT use the system in hazardous environment.

• DO NOT expose the system to high humidity, chemical environment or mechanical impact.

• DO NOT attempt to repair the system yourself – any repairs must be carried out by fully qualied personnel only.

Disconnect the mains power before installing. Never install or carry out maintenance during stormy weather. The electric sock-

et that powers the system must be easily accessible.

Please use the 10-24V 50Hz ~200mA AC or 10-24V 200mA DC power supply unit that meets the EN 60950-1 standard.

Any additional device you connect to the system, such as a computer, must also be powered by an EN 60950-1 approved

supply. When connecting the power supply to the system, switching the polarity terminal places does not have any aect.

External power supply can be connected to AC mains only inside installation room

with automatic 2-pole circuit breaker capable of disconnecting circuit in the event

of short circuit or over-current condition. Open circuit breaker must have a gap

between connections of more than 3mm and the disconnection current 5A.

Phase

AC 230V

50 Hz/DC 24V

USB cable

Null

GS-500

AC/DC

To switch the system o, unplug the external electric power supply from or any other linked device that the system is

powered from

A blown fuse cannot be replaced by the user. The replacement fuse has to be of the kind indicated by the manufacturer (fuse

F1 model – MINISMDC050F 0.5A).

If you use a computer for the device conguration, it must be earthed.

The WEEE (Waste Electrical and Electronic Equipment) symbol on this product (see left) means it must not be disposed of in

household waste. To prevent possible harm to human health and/or the environment, you must dispose of this product in an

approved and environmentally safe recycling facility. For further information contact your system supplier, or your local waste

authority.

3EN

Manual GS-500_EN_2014-01

CONTENTS

1. GENERAL INFORMATION ...........................................................................................................................................................6

2. TECHNICAL SPECIFICATIONS ....................................................................................................................................................6

2.1. Electrical & Mechanical Characteristics.........................................................................................................................................................6

2.2. Main Unit, LED Indicator & Connector Functionality ...................................................................................................................................7

2.3. Wiring Diagrams ................................................................................................................................................................................................8

3. INSTALLATION ...........................................................................................................................................................................9

4. GENERAL OPERATION .............................................................................................................................................................10

5. CONFIGURATION METHODS ....................................................................................................................................................10

5.1. SMS Text Messages.........................................................................................................................................................................................10

5.2. Programming button USR/PROG ..................................................................................................................................................................10

5.3. GS-Congurator...............................................................................................................................................................................................10

5.4. Remote Conguration via Web Browser......................................................................................................................................................10

6. SYSTEM LANGUAGE.................................................................................................................................................................12

7. SMS PASSWORD.......................................................................................................................................................................13

8. ADMINISTRATOR PHONE NUMBERS.......................................................................................................................................13

9. DATE AND TIME........................................................................................................................................................................15

9.1. Automatic Date and Time Synchronization ................................................................................................................................................15

10. USER PHONE NUMBER DATABASE ..................................................................................................................................17

10.1. User Validity and Access Restriction .......................................................................................................................................................... 20

11. OUTPUTS..........................................................................................................................................................................23

11.1. Output Names..................................................................................................................................................................................................23

11.2. Output Control by Free of Charge Phone Call ............................................................................................................................................ 24

11.3. Output Control by SMS Text Message..........................................................................................................................................................25

11.4. Output Control Conrmation by Call Back ...................................................................................................................................................27

11.5. Output Control from any Phone Number.....................................................................................................................................................27

11.6. Automatic Output Control............................................................................................................................................................................. 28

12. SCHEDULERS................................................................................................................................................................... 29

13. EVENT LOG .......................................................................................................................................................................31

14. INPUTS .............................................................................................................................................................................33

14.1. Input Names and Alarm Notications..........................................................................................................................................................33

14.2. Disabling and Enabling Inputs.......................................................................................................................................................................35

15. SYSTEM INFORMATION. INFO SMS................................................................................................................................. 36

15.1. Periodic Info SMS............................................................................................................................................................................................ 36

16. SYSTEM NOTIFICATIONS..................................................................................................................................................37

16.1. SMSC (Short Message Service Center) Phone Number.............................................................................................................................37

17. GPRS NETWORK SETTINGS .............................................................................................................................................37

18. REMOTE SYSTEM RESTART ............................................................................................................................................ 38

19. TECHNICAL SUPPORT ..................................................................................................................................................... 39

19.1. Troubleshooting ............................................................................................................................................................................................. 39

19.2. Restoring Default Parameters ..................................................................................................................................................................... 39

19.3. Updating the Firmware via USB Cable ........................................................................................................................................................ 39

4EN Manual GS-500_EN_2014-01

5EN

Manual GS-500_EN_2014-01

Limited Liability

The buyer agrees that the system will reduce the risk of re, theft, burglary or other danger but that it does not guarantee against the

occurrence of such events. Entrya Technologies BVBA will not take any responsibility for the loss of personal eects, property or revenue

whilst using the system. The liability of Entrya Technologies BVBA is limited to the value of the system purchased. Entrya Technologies

BVBA is not aliated with any mobile/wireless/cellular provider and is therefore not responsible for the quality of such services.

Manufacturer Warranty

The warranty complies with statutory requirements. Your local stockist should be contacted in connection with any warranty-related

matters. Your warranty entitlements only apply to the country in which the GSM remote control was purchased. If you require after-sales

service, spare parts or accessories, please contact your specialist retailer. The warranty remains valid only if the system is used as intend-

ed, following all guidelines outlined in this manual and in accordance with the operating conditions specied. The warranty is void if the

system has been exposed to mechanical impact, chemicals, high humidity, uids, corrosive and hazardous environments or force majeure

factors.

Dear Customer,

Thank you for choosing to purchase the GSM remote control GS-500. Your thoughtful decision will ensure reliable solution for many

years as all Entrya Technologies BVBA products are manufactured to meet the highest standards.

We are condent that you will be completely satised with your product. However, in the unlikely event that you do experience a

problem, please contact the dealer from whom you made your purchase.

Entrya Technologies BVBA

Contents of Pack

Item Quantity

1. GS-500.....................................................1

2. Short manual ..........................................1

3. GSM antenna. .........................................1

It is strictly forbidden to copy and distribute information in this document or pass to a third party without an advanced

written authorization from Entrya Technologies BVBA. Entrya Technologies BVBA reserves the right to update or modify

this document and/or related products without a warning. Hereby, Entrya Technologies BVBA declares that the GSM

switch-gate controller GS-500 is in compliance with the essential requirements and other relevant provisions of Directive

1999/5/EC. The declaration of conformity may be consulted at www.entrya.eu

6EN Manual GS-500_EN_2014-01

1. GENERAL INFORMATION

GS-500 is a micro-controller based device intended to provide access control for gate automatics, road barriers or to remotely turn ON/OFF

any electrical appliance via the GSM network.

Examples of using the system:

• Access control.

• Parking lot control of residential houses or oces.

• Gate control of private houses.

• Any electrical appliance control: lighting, watering, heating etc.

• Remote reboot of the “frozen” systems, such as computer network or a server.

Main features

• Manual output control by free of charge phone call.

• Automatic output control in accordance with the scheduled time.

• Congurable output pulse duration.

• Automatic date and time synchronization.

• Up to 5 administrators for system conguration by SMS text messages, acceptance of input alarm SMS text messages, output control

by SMS text message and free of charge phone call.

• User database capacity – up to 500 users for output control by free of charge phone call.

• User phone number validity limitation in accordance with a set deadline (date/time) or number of rings to the system.

• Output control restriction for users in accordance with the specied weekdays and time.

• Event log of 1000 events containing date and time as well as administrator/user phone number and user name who controlled the

output.

• 3 inputs with customizable alarm texts for notication on gate state or in case it gets jammed.

• Periodic self-test notication by SMS text message to administrator phone number.

2.TECHNICAL SPECIFICATIONS

2.1. Electrical & Mechanical Characteristics

Supply voltage 10-24V 50Hz ~ 200mA max / 10-24V 200mA max

Current used in standby mode up to 50mA

GSM modem frequency 850/900/1800/1900 MHz

Number of outputs 2

Output type Relay; NO (normally-open)

Maximum commuting output values 24V 50Hz ~ 0,5A / 24V 1A

Number of “low” level (negative) inputs 2

Number of “high” level (positive) inputs 1

“Low” level (negative) input value range 0... 16V -0.8... -0.4mA

“High” level (positive) input value range 5... 50V 0.17 .... 1.7mA

“Low” level (negative) and “high” level

(positive) input connection type

NO (normally-open)

Dimensions 70x90x35mm

Operating temperature range -20…+55oC (-30...+55oC with limitations)

Humidity 0-90% RH @ 0... +40 °C (non-condensing)

7EN

Manual GS-500_EN_2014-01

2.2. Main Unit, LED Indicator & Connector Functionality

AC/DC OUT1 OUT2 COM IN3 IN2 IN1

ANT

USB

SIM CARD

G S M

MO DE M

USR

PROG

MIC

DEF

GSM (g)

GSM (r)

STATUS

Main Unit Functionality

ANT GSM antenna SMA type connector

USB Mini USB port

SIM CARD SIM card slot / holder

GSM MODEM GSM network 850/900/1800/1900 MHz modem

USR PROG button for setting user telephone numbers

GSM (g) Green light-emitting diode indicating GSM signal strength

GSM (r) Red light-emitting diode indicating SIM card status

STATUS Bue light-emitting diode indicating PROG mode

DEF Pins for restoring default settings

F1 0.5A fuse

Connector Functionality

AC/DC Power supply terminals

OUT1 Output C1 terminal

OUT2 Output C2 terminal

COM Common terminal

IN3 “Low” level (negative) input Z3 terminal; dry NO contact

IN2 “High” level (positive) input Z2 terminal; 5...50 Vdc

IN1 “Low” level (negative) input Z1 terminal; dry NO contact

8EN Manual GS-500_EN_2014-01

LED Indicator Functionality

GSM (r) SIM card status

Steady ON SIM card is not yet connected to the GSM network / SIM card is not present / PIN code enabled

OFF SIM card is operating successfully

GSM (g) GSM signal strength STATUS programmation mode

OFF No GSM signal OFF standard operation

Flashing every 1 sec. Poor Steady ON Programmation telephone

Flashing several times per sec. Medium numbers activating OUT1 &

OUT2 simultaneous

Steady ON Excellent Flashing every 1 sec. Programmation telephone

numbers activating OUT1

Flashing 2 times

per sec.

Programmation telephone

numbers activating OUT2

2.3. Wiring Diagrams

General wiring

GS-500

AC/DC

Power

supply

Gate automatics

device

RELAY1 RELAY2

COM Z3 Z2 Z1

Gate automatics

device

Example of GS-500 system wiring to gate automation device

GS-500

AC/DC OUT1 OUT2 COM IN3 IN2 IN1

Motor 1

Motor 2

power supply

accesories

230 V

Ground

Flash light

Start

Partial opening

Safety input

Relais

Motor

L N PE PE

Push

Button

24 V

Control board gate opener

Position

indicator

9EN

Manual GS-500_EN_2014-01

3.INSTALLATION

• The system should be installed indoors, in stationary environment ONLY.

• For the connection of input/output terminals, use 0.50 mm21 thread unshielded cable of up to 100 meters length.

1. Wire up the system in accordance with the wiring diagrams (see 2.3 Wiring Diagrams for more details).

2. Connect the GSM antenna. Based on the type of the GSM antenna supplied with GS-500 unit, follow the recommendations for the

antenna installation:

GSM

antenna

Never install in the following

locations:

• inside a metal cabinet

• closer than 20 cm from the

metal surface and/or power

lines

3. Disable the PIN code request and the automatic voice mail of the SIM card by inserting it into a mobile phone and following the proper

menu steps.

4. Once the PIN code and voice mail are disabled, insert the SIM card into the SIM card slot / holder of GS-500 system.

5. Make sure the antenna is connected and power up the system, wait until indicator GSM (r) goes out indicating SIM card status.

6. Once the indicator GSM (r) lights OFF, the illuminated indicator GSM (g) lights up indicating that the system has successfully connected

to the GSM network. To nd the strongest GSM signal, position the GSM antenna and follow the indications provided by GSM (g) indica-

tor (see 2.2. Main Unit, LED Indicator & Connector Functionality for more details).

7. Change the system language if necessary (see 6. SYSTEM LANGUAGE for more details).

8. Change the default SMS password (see 7. SMS PASSWORD for more details).

9. Set the phone number for Admin 1 (see 8. ADMINISTRATOR PHONE NUMBERS for more details).

10. Set system date and time (see 9. DATE AND TIME for more details).

11. Once the system is fully congured, it is ready for use. However, if you fail to receive a reply by SMS text message from the system,

please check the SMSC (Short Message Service Center) phone number. For more details regarding the SMS center phone number,

please refer to 17. SMSC (Short Message Service Center) Phone Number.

ATTENTION: The system is NOT compatible with pure 3G SIM cards. Only 2G/GSM SIM cards and 3G SIM cards with 2G/GSM prole

enabled are supported. For more details, please contact your GSM operator.

ATTENTION: We also recommend you to disable call forwarding, voice mail/text message reports on missed/busy calls and

similar services that might cause incorrect system operation. Please contact your GSM operator for more details on these services and

how to disable them.

NOTE: For maximum system reliability we recommend you do NOT use a Pay As You Go SIM card. Otherwise, in the event of insucient

credit balance on the SIM card, the system would fail to make a phone call or send SMS text messages.

NOTE: We advise you to choose the same GSM SIM provider for your system as for your mobile phone. This will ensure the fastest,

most reliable SMS text message delivery service and phone call connection.

NOTE: Even though the installation process of GS-500 is not too complicated, we still recommend to perform it by a person with basic

knowledge in electrical engineering and electronics to avoid any system damage.

10 EN Manual GS-500_EN_2014-01

4.GENERAL OPERATION

When a phone call is made to the phone number of the SIM card inserted in GS-500, the system will verify if the caller’s phone number exists

in the memory. If the caller is one of the 5 administrators or the phone number belongs to one of the 500 database users, the system will

reject the phone call, thus making the phone call free of charge, and open the gate. By ringing to GS-500 again, it will close the gate. If the

phone number is not recognized, the system will reject the phone call and ignore it. The GSM switch-gate controller can also control your

gate automatically in accordance with the scheduled time or by sending an SMS text message from the administrator’s phone number.

By connecting a sensor to one of the 3 inputs, the administrators can receive SMS text messages regarding the gates that failed to close

during the set time period.

User/Admin

CALL

5.CONFIGURATION METHODS

5.1. SMS Text Messages

!!! In this installation manual the underscore character ”_” represents one space character. Every underscore character

must be replaced by a single space character. There must be no spaces or other unnecessary characters at the beginning

and at the end of the SMS text message.

SMS

In order to congure and control the system by SMS text message, send the text command to the GS-500 system phone num-

ber from one of the preset administrator phone numbers. The structure of SMS text message consists of 4-digit SMS password

(the default SMS password is 0000 – four zeros), the parameter and value. For some parameters the value does not apply e. g.

STATUS. The variables are indicated in lower-case letters, while a valid parameter value range is indicated in brackets.

5.2. Programming button USR/PROG

With the button USR / PROG it is possible to add or delete phone numbers in a simple way. This option can not be used until

the SMS password and at least one administrator is congured with SMS text messages or using the GS-Congurator soft-

ware via USB or GPRS.

GS-Congurator is freeware and can be downloaded at: www.entrya.eu/en/download

5.3. GS-Congurator

Cong

Tool

Software GS-Congurator is intended for GS-500 GSM remote control conguration via USB port locally. This software simpli-

es system conguration process by allowing to use a personal computer in the process. Before starting to use GS-Congu-

rator software, please read the user guide provided in the software’s HELP section.

GS-Congurator is freeware and can be downloaded at: www.entrya.eu/en/download

NOTE: GS-Congurator is secured with SMS password. The default SMS password is 0000 (see 7. SMS PASSWORD).

5.4. Remote Conguration via Web Browser

WEB

BROWSER

The system comes equipped with a remote conguration feature allowing to congure the parameters via any available web

browser. Before remotely connecting to GS-500 via GPRS connection, ensure that:

• SIM card is inserted into the SIM CARD slot (see 2.2. Main Unit, LED & Connector Functionality).

• Mobile internet service (GPRS) is enabled on the SIM card.

• GS-500 is powered up.

• Default SMS password is changed to a new 4-digit password (see 7. SMS PASSWORD).

• Admin 1 phone number is set up (see 8. ADMINISTRATOR PHONE NUMBERS).

• APN, user name and password are set up (see 17. GPRS NETWORK SETTINGS).

GS-500

Table des matières

Autres manuels Entrya ouvre-porte

Entrya

Entrya ENIRO30/1 Mode d’emploi

Manuels ouvre-porte populaires d'autres marques

Elite

Elite CSW200UL Manuel utilisateur

CAME

CAME FROG-PM4 Manuel utilisateur

SOMFY

SOMFY FX230 Manuel utilisateur

Aprimatic

Aprimatic ONDA 500 Manuel utilisateur

Turnstiles

Turnstiles FSW 900 Manuel utilisateur

Erreka

Erreka BUL BL33 Mode d'emploi

Erreka

Erreka VULCAN S Manuel utilisateur

Beninca

Beninca R1-2 WBV Manuel utilisateur

Erreka

Erreka VULCAN D Manuel utilisateur

Motorline professional

Motorline professional FORT Mode d’emploi

Beninca

Beninca BOB5024 Manuel utilisateur

AGA

AGA GATEMASTER 900 HD Manuel utilisateur

Chamberlain

Chamberlain MotorLift HC280ML Manuel utilisateur

SOMFY

SOMFY Dexxo RTS Pro Manuel utilisateur

Cardin

Cardin BL Series Manuel utilisateur

Westfalia

Westfalia 85 27 06 Manuel utilisateur

CAME

CAME F500 Manuel utilisateur

Extel

Extel VERA Manuel utilisateur