Ensol ES1V2.0 Manuel utilisateur

Installation instruction

of the flat solar collectors models ES1V2.0, ES1V2.65,

ES2V/2.0 AL, ES2V/2.65

integrated in the slate roof.

Installation instruction

of the flat solar collectors models

ES1V2.0, ES1V2.65,

ES2V/2.0 AL, ES2V/2.65

integrated in the slate roof.

02/2012 Get acquainted before starting the installation.

Installation instruction

of the flat solar collectors models ES1V2.0, ES1V2.65,

ES2V/2.0 AL, ES2V/2.65

integrated in the slate roof.

1. Introduction

Lightning protection

In case the height at which the collectors are to be installed exceeds 20 metres

and a building is not equipped with the lightning protection it is necessary to

connect all electrically conducting elements with an earth rod (minimal earth

rod cross-section – 16mm

), and then with a compensating potential.

In case the height at which the collectors are to be installed does not exceed

20 metres it is not necessary to provide the lightning protection.

If the building is equipped with the lightning protection it is important to

check the connection of the solar system to the lightning protection. That task

should be performed by an electrician.

Recycling

Completely used up solar collectors can be returned to the manufacturer.

The returned solar collectors shall be utilized by the manufacturer in the way

which is the least burdensome for the natural environment.

2. Safety during installation

Before commencing the installation work it is necessary to immediately

get acquainted with the safety tips!

2.1. Notes included in the instruction.

The installation instruction includes important information concerning safety

and proper positioning of the collectors on the roof as well as the correct

execution of the hydraulic connection. Drawings and information included in

the instruction apply to a vertical installation of the collectors.

Installation of the collators can only be performed by qualified personnel with

professional experience in the field of water supply and gas systems.

Upon completion of works an installer should hand over the installation

instruction to a customer and clearly explain the principles of operation and

directions essential to a proper operation of the solar system.

2.2Application

This instruction includes a description of an vertical assembly set to carry out

the installation of solar collectors (vertically and horizontally) on the roof

with the inclination ranging from 30

up to 65

The assembly set shall exclusively be used to perform the installation of solar

collectors, it must not be used to install different devices on the roof.

Installation of only solar collectors on the supporting structure guarantees its

safety of operation.

Installation instruction

of the flat solar collectors models ES1V2.0, ES1V2.65,

ES2V/2.0 AL, ES2V/2.65

integrated in the slate roof.

3. Before commencing the installation.

Directions!

As the work on the roof can be dangerous it is recommended to hire a

roofwork firm.

DANGER OF GETTING SCALED.

In case the collectors and assembly materials are exposed to solar radiation

for a long time, there is a risk of getting scalded by hot elements.

In order to avoid the danger of scalding you should:

use protective clothing,

cover the collectors and the assembly materials with canvas cover

(thanks to which the heating up by sunbeams will be reduced).

3.1 Transport and storage.

during transport the collector connectors are protected by rubber caps,

collectors should be stored in a dry place. In case the collectors are stored

outside they should be protected against weather conditions.

3.2 Technical Documentation

Solar installation set consists of different components. Before

installing any of the components you should become

familiar with an adequate instruction.

A separate installation instruction is attached to a given device or a piece

equipment.

Installation instruction of solar collectors,

installation instruction of the pump group,

installation instruction of the solar controller,

installation instruction of the hot water container.

3.1 Completeness of delivery

Before commencing the installation it is necessary to check if the delivery is

complete and the delivered components are free of damage.

−in case of discovering any damages the defected elements or parts should

be immediately replaced,

−the replacement needs to be carried out with the application of original

spare parts only.

−the basic set is designed for two solar collectors, extending the solar

instalation for each successive solar collector is associated with

purchase an aditional extension set for each solar collector

Installation instruction

of the flat solar collectors models ES1V2.0, ES1V2.65,

ES2V/2.0 AL, ES2V/2.65

integrated in the slate roof.

List of Items

Basic set Extension set

Description Quantity

Left top edge flashing 1 -

Right top edge flashing 1 -

Top extension flashing 1 1

Left lower edge flashing 1 -

Right lower edge flashing 1 -

Lower extension flashing 1 1

Left side flashing 1 -

Right side flashing -

Hook-in element -

Connecting plates 26 -

Centre flashing 1 1

Support frame for centre flashing 1 1

Cover flashing left 1 -

Cover flashing right 1 -

Cover flashing 1

Wind protection rail 2 1

Collector bracket 4 2

Collector clamping (40 x 40mm) 4 -

Linear collector clamping bar (114 x 30mm) 2 2

Seal strip 20/20 5lfm 1,5lfm

Wood wedge 2 1

Coloured and sealed screw 4,5 x 35mm 2

Self-tapping screw A2 4,2 x 13mm 9

Coloured and sealed self-tapping screw A2 4,2 x 13mm 14 7

Sheet strip 2

Wood screw 4 x 30mm 28 10

Wood screw 5 x 40mm 12 4

Wood screw 5 x 110mm 6 3

3.4Additional tools and equipment

- level,

- harness with protective rope (to work high above ground),

−

scaffolding, a roof ladder or a crane.

Installation instruction

of the flat solar collectors models ES1V2.0, ES1V2.65,

ES2V/2.0 AL, ES2V/2.65

integrated in the slate roof.

3.5 Location of a collector

Potential quantity of the absorbed radiation depends on a proper location of

the absorber in relation to falling sunbeams.

Optimum is a perpendicular position of a collector surface in relation to the

falling solar radiation.

Recommended location of a collector:

inclination angle:

40 – 45

for a year-long installation,

approximately 30

for installations used in summer,

approximately 60

for installations used in winter,

positioning of a collector in the southern direction (or approximate to the

southern direction).

Solar collectors must not be installed at the inclination below 30

over 75

It is recommended to install the collectors on the southern roof slope. During

the installation work particular attention should be paid to protect the

collectors from being overturned by strong winds. Permissible snow

and wind load amounts to max. 2,0 kN/m².

Collectors field should be located in such a way that the absorber will

not be shadowed by the adjacent buildings, trees, etc.

In case of a larger number of collector fields it is important that the front row

of the collectors do not shadow the back one.

3.6 Technical data for the flat collector models: ES1V/2.0, ES1V/2.65,

ES2V/2.0 AL, ES2V/2.65

Flat collector

Symbol ES1V/2.0 ES2V/2.0 AL

ES1V/2.65 ES2V/2.65

Unit

Width A 1006 1006 1120 1120 mm

Height B 2007 2007 2356 2356 mm

Depth C 85 85 85 85 mm

Collector weight m 40 40 49 49 kg

Area S 2,02 2,02 2,65 2,65 m

Connectors: Cu pipe Φ22 22 22 22 mm

Fluid volume V 1.8 1.8 2.2 2.2 dm

Max working pressure p

max

6.0 6.0 6.0 6.0 bar

Optimum flow min. - max. m 60-90 40-60 75-105 75-105 dm

Required space

ES1V/2,0 and ES2V/2,0 AL for vertical installation

Required about 2400 mm in height and 1800 mm in width for the first

collector and + 1110 mm in width for each consecutive one. In case of

mounting a collector on the inclined roof the minimum distance between

collectors and the roof edge is 1m.

Installation instruction

of the flat solar collectors models ES1V2.0, ES1V2.65,

ES2V/2.0 AL, ES2V/2.65

integrated in the slate roof.

ES1V/2,65, ES2V/2,65 for vertical installation

Required about 2800 mm in height and 1900 mm in width for the first

collector and + 1220 mm in width for each consecutive one. In case of

mounting a collector on the inclined roof the minimum distance between

collectors and the roof edge is 1m.

3.7 Flow resistance for collectors

3.8 Warranty conditions of the installation and use of the collectors ES2V/2.0 AL

with aluminum absorber

It is allowed to use only solar fluids that is accepted and offered by the producer, e.g.

ENSOLICOL-AL -25,

It is allowed to wash the solar thermal system and perform the leak test only with solar fluid,

The solar thermal system must be closed (hermetic):

−the solar system can not contain automatic vents (potential place through the installation can

get into air),

−before the first start, the solar system must be completely deaerated, and be leakproofed by

the plumber,

−any leaks are associated with getting air into the solar thermal system with maximize the risk

of corrosion. Once air get into the solar system the solar fluid must be replaced.

It is allowed to use only connections systems that are offered by the producer,

It is recommended to do the solar system with flexible stainless steel tubes or steel tubes. It

is forbidden to connect directly the connector pipe of the collector witch any copper or brass

parts of the solar system witch increases the possibility of electrochemical corrosion.

1-10 x ES2V/2,0 AL

100

40 90 150 210 270 330 390 450 510 570 630 690 750 810 870

liquid flow [dm

/h]

pressure drop [mbar]

1-2 3-4 5-6 7-8 9-10

1-10 x ES2V/2,65 i ES2H/2,65

100

120

140

160

120

180

240

300

360

420

480

540

600

660

720

780

840

900

960

1020

1080

1140

1200

1260

1320

1380

liquid flow[dm

/h]

pressure drop [mbar]

1-2 3-4 5-6 7-8 9-10

ES1V/2,0

50 100 150 200 250 300

liquid flow[dm3/h]

pressure drop[mbar]

ES1V/2,65

0 20 40 60 80 100 120 140 160 180 200

liquid flow [ dm

/h]

pressure drop [mbar]

Installation instruction

of the flat solar collectors models ES1V2.0, ES1V2.65,

ES2V/2.0 AL, ES2V/2.65

integrated in the slate roof.

4. Installation and commissioning of the solar system:

4.1 Installation of the collectors on the roof

4.2 Installation of the connection system - hydraulic connection of the collector

4.3 Leak test and commissioning of the installation

4.4 Enclosure of the solar system

THE MONTER / INSTALLER MUST BE SURE OFA CORRECT

INSTALLATION AND LEAKPROOF OF THE COLLECTORS BEFORE

ENCLOSING THE SOLAR SYSTEM!

Attention: This flashing only can be used in the combination of “double-lap slating”!

The minimum roof pitch for the installation of this flashing is 30°!

Into consideration of mandatory safety measures uncover the roof for the assembly of the

roof integrated solar collectors (500mm broader as requested for the collectors).

4.1.1 Installation and positioning an additional batten

Attach an additional batten at the lower end

(with the

same dimensions as the existing

one) in a distance of 160mm along the total

width

of the installation. This is needed to

counteract the snow load!

ok in the left lower edge flashing at the

upper batten. Mount it together with a

collector bracket by the

help of a wood

screw (4 x 30mm) at the provided holes in

the sheet.

This connecting link must overlap the tile

10mm at least!

Please note: The lower frame

must have a roof pitch!

Installation instruction

of the flat solar collectors models ES1V2.0, ES1V2.65,

ES2V/2.0 AL, ES2V/2.65

integrated in the slate roof.

4.1.2 connecting the lower edge flashing

4.1.3 connecting the lower edge flashing

4.1.4 montage of the solar panels

Connect the left edge with the lower extension

flashing. Push them together till the indicated

mark is reached. Fix it again together with a

collector bracket by the help of a wood screw

(4 x 30mm) at the provided hole.

Repeat this procedure with the right lower edge.

Place the left solar collector on the lower

flashing (exact on the indication mark).

Insert the collector in the collector bracket.

Indication mark

Installation instruction

of the flat solar collectors models ES1V2.0, ES1V2.65,

ES2V/2.0 AL, ES2V/2.65

integrated in the slate roof.

4.1.5 montage of the collector clampings

4.2 Installation of the connection system - hydraulic connection of the collector

4.2.1. Hydraulic connection of the harp collectors ES1V/2.0 and ES1V/2.65

Directions!

Hydraulic conduits and fixtures can be connected at the left or right side of

the collector battery. The instruction presents the connection at the right side,

as an example.

One-sided connection of maximum 5 collectors.

When forming a battery you can connect maximum 5 collectors.

elbow Expansion joint cross-fitting

Fix the left collector

at the upper and lower

left side by the help of the collector clamping

(40 x 40mm) and wood screws (5 x 40mm).

Afterwards place the right collector. Set both

linear collector clamping bars (114 x 30mm)

bet

ween the collectors, push the collectors

together and screw the clamping bars down

by wood screws (5 x 40mm). Fix the right

collector also at the upper and lower side by

the help of collector clamping (40 x 40mm)

and wood screws (5 x 40mm).

Collector clamping

Installation instruction

of the flat solar collectors models ES1V2.0, ES1V2.65,

ES2V/2.0 AL, ES2V/2.65

integrated in the slate roof.

4.2.2. Hydraulic connection of the meander collectors ES2V/2.0AL. ES2V/2,65

Directions!

The power supply and return must be connected to the diagonal of the

collector or the battery. The power supply should be connected to the lower

connection and the return to the top connector. The Connection for power

supply/return is arbitrary – in can be from the left or right sight. In the two

other connections should be clamps. The instruction presents the connection

at the right side, as an example.

One-sided connection of maximum 10 collectors.

When forming a battery you can connect maximum 10 collectors.

clamp expansion joint cross-fitting

elbow expansion joint clamp

4.2.3 Connecting the collectors with a clamping pipe union.

Collectors ES1V/2.0 and ES1V/2.65 – connecting upper connectors pipe

Collectors ES2V/2.0 AL, ES2V/2.65 – connecting upper and bottom

connector pipe

1 – connector pipe of

the collector

2 – strengthening sleeve

3 – pipe union nut

4 – clamping ring

5 – pipe union nipple

Mount the pipe union on the first collector, then move

the second collector closer and fasten the pipe union on both collectors.

−

place the strengthening sleeve (2) in the connector pipe of the collector (1),

−

pipe union nut (3) should be put on the connector pipe of the collector (1),

−

clamping ring (4) should be placed on the connector pipe of the collector,

−

screw the nut (3) onto the pipe union body,

−

place the strengthening sleeve in the connector pipe of the second collector,

−

put the nut on the connector pipe of the second collector,

−

place the clamping ring on the connector pipe of the second collector,

−

move the second collector closer to the pipe union,

−

screw the nut onto the pipe union nipple.

Autres manuels pour ES1V2.0

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels ensol Panneau solaire

ensol

ensol ES2H/2.65 Manuel utilisateur

Manuels Panneau solaire populaires d'autres marques

Navitron

Navitron HFC-2 Manuel utilisateur

AXITEC

AXITEC 60-CELL Manuel utilisateur

thermital

thermital TSOL 20 N BLU Manuel utilisateur

AZO Digital

AZO Digital MPPT-3000 Manuel utilisateur

Clenergy

Clenergy PV-ezRack SolarTripod Manuel utilisateur

Beretta

Beretta SCF-20N Manuel utilisateur

moovo

moovo KSM001 Manuel du produit

solarwatt

solarwatt EasyIn 60M Series Manuel utilisateur

Solarland

Solarland Portable Series Manuel

Ubiquiti

Ubiquiti sunMAX Manuel utilisateur

Lippert

Lippert Furrion FSFP37MW-BL Manuel utilisateur

Sonnenkraft

Sonnenkraft GK5-HP Manuel utilisateur

REC

REC TwinPeak 2S Mono 72 Series Manuel utilisateur

Sunforce

Sunforce 50039 Manuel utilisateur

Flexsolar

Flexsolar C100 Mode d’emploi

Süd Solar

Süd Solar 03005 Manuel utilisateur

Kodak

Kodak SP21 Manuel utilisateur

Carmanah

Carmanah Go Power! Solar Flex GP-FLEX-30 Manuel utilisateur

ensol ES1V2.0 Manuel utilisateur

Manuels Panneau solaire populaires d'autres marques