ENGWE-BIKES EP-2 Manuel utilisateur
ENGWE-BIKES
Operation and maintenance manual
Before using the e-bike, please read the attached operating instructions.
Carefully read the safety rules.
1
IMPORTANCE
When using the electric bicycle, basic safety precautions should always be
followed, including the following:
1. Read all instructions.
2. To protect against fire, electric shock and injury to persons, do not immerse
cord, plugs, or e-bike in water or other liquid.
3. Close supervision is necessary when the e-bike is used by or near children.
4. Unplug from outlet when not in charging and before cleaning.
5. Do not operate the e-bike with a damaged cord or plug or after the e-bike
malfunctions, or has been damaged in any manner. Take the e-bike to the
nearest authorized service bike shop for examination, repair or adjustment.
6. The use of accessory attachments not recommended by the e-bike
manufacturer may result in fire, electric shock or injury to persons.
7. Do waterproof when using on a rainy or snowy day.
8. Do not let cord hang over the edge of table or counter, or touch hot
surfaces.
9. Do not place on or near a hot gas or electric burner, or a heated oven.
10. Always attach the plug to the battery first, then plug the cord into the wall
outlet.
11. Do not use the bike for other than intended use.
12. Save these instructions.
SAVE THESE INSTRUCTIONS
2
EP-2 / EP-2 Pro / ENGINE Pro
* Please note that this is a general manual. So, the frame style of the
electric bicycle (e-Bike) that you have may differ from the picture
shown in this manual.
3
PLEASE NOTE:
This manual is not intended as a detailed user, service, repair or maintenance manual.
Please seek assistance from a qualified technician for service, repairs or maintenance.
Importance………………..
……………………………………………………
P1
Compliance with the Law
………………………………………………….
P4
Assembling …………………………………………………………………………
P5
Operating Your New e-Bike
…………………………………………………
P10
Maintenance
………………………………………………………………………
P13
Specifications
……………………………………………………………………
P14
Safety
………………………………………………………………………………
P15
Trouble Shooting …………………………………………………………………
P17
4
Read This First: Safety and Compliance with the Law
Congratulations on your purchasing of your new e-bike. Your new e-bike is an
excellent piece of personal transportation equipment that will give you good service for
many years.
Before you start using your e-bike, we want you to be aware of a few important points.
Please read this section carefully..
Observe Laws Regarding the Use of Battery-Operated Bicycles
Your e-bike is designed and manufactured to meet safety requirements as a
battery-operated bicycle. However, state and local laws governing the use of
battery-operated bicycles on public roadways, parks, and other open areas may
differ. Please check with your local authority before using your e-bike in public
areas.
Observe Laws Regarding the Use of Bicycles
Note that all laws regarding the use of bicycles in public areas, such as those
mandating the use of helmets and the use of infant seats, will automatically
apply for e-bikes. Check with your local authority on what restrictions might
apply.
The Lithium-ion Battery of Your e-Bike
Your e-bike is equipped with the latest battery technology. The lithium-ion
battery is much lighter than lead- or nickel-based batteries that are being used
in some older models.
Your First Ride
Please be VERY CAREFUL when you are ready to get on your e-bike for the first
time because that the e-bike moves significantly faster than a regular bicycle at
active power-assisted mode. Take your e-bike to an area with a lot of open space
before you start. Do not start pedaling hard as soon as you get on the e-bike (as
you normally would be with a regular bicycle), as the e-bike will accelerate under
pedal-assist mode and you may be unprepared for the sudden increase in speed.
However, after a few times, you will enjoy using the pedal-assisted function.
5
Assembling Your New e-Bike
If you purchased your e-bike unassembled, please follow these instructions to
assemble your e-bike under the guidance of an adult or a qualified technician.
Assembly is quite easy as most of the parts are already assembled; you need only to
put a few large pieces together to complete the job.
For more information, please refer to this website: www.engwe-bikes.com.
Name of each Part
Speed sensor
Rear derailleur
Brake caliper
6
Check that the Package is Complete and Undamaged
Your e-bike comes in a carton containing the following:
The main body of the e-bike – consisting of the frame, the rear
wheel, the gear and chain, the rear brake, the battery in the
frame, the rear fender.
The handlebar subassembly with the battery’s keys that attached
on it – the handlebar subassembly is not really separate, as it is
connected to the main body by the brake cables and electrical
wires. The handlebar also has the brake levers and gear control
already assembled. Additionally, the right handle also has an
integrated control for the throttle mode power-assisted, a display
panel.
The Seat – the seat is attached to its pedestal stem.
The front wheel
The front wheel fender with supports
Front light – the front light is not really separate, as it is connected
to the main body by an electrical wire.
Tools and other parts – One multi-tools, one charger, a pair of
foot pedals and this manual, they are contained in a separate
box.
7
Assembly - Step 1: Attach the handlebar subassembly
Stand the main body of the e-bike on the kickstand. Stand up and lock the steering
column that is at the front of the main body frame, insert the stem of the handlebar
subassembly into it. Make sure that the fork (that will hold the front wheel) is
pointing forward, and orient the handlebar accordingly. Insert the stem all the way
and tighten from the top using the quick lock.
Assembly - Step 2: Attach the Front Wheel Fender and the Front Light
Make sure that the fork from the steering column is pointing forward. Place the
front light and the front fender within the fork: locate the small projection with a
screw hole at the top of the fender, fit it to the bolt at the back of the base of the
steering column; attach the supports (one on each side) to the base of the fork
using two small bolts (supplied). After all three points (the dorsal point and the 2
support points) are properly attached, use the multi-tools to tighten.
8
Assembly - Step 3: Attach the Front Wheel and Adjusting the Front Brake
Make sure that the fork from the steering column is pointing forward. Remove the
protective bar from the front fork, place the front wheel within the fork and the
brake disc within the brake block, seat the axial stem properly within the
receptacles at the tips of the fork, and tighten the nuts with the multi-tools. Make
sure that the front wheel moves freely and does not wobble from side to side.
Reposition the wheel and re-tighten if necessary.
Test the brake by lifting the front of the e-bike and setting the wheel in motion
(turn it) and apply the brake at the handlebar to stop it. If you could not set the
wheel in free motion, or if you could not stop it by applying the brake, you need
to re-adjust by increasing or decreasing the clearance.
Caution: Do not operate the e-bike until you are satisfied that both the front and
rear brakes are operational.
Assembly - Step 4: Installing the Seat and Pedals
Insert the pedestal stem of the seat into the seat column of the main body frame,
use the built-in lever to tighten.
Attach a pedal on each side of the crank, tighten with the multi-tools.
Inflate the tires to proper pressure.
At this point, your e-bike is a completely functional bicycle, although without any
battery operated to function as yet. Check all tightening points to make sure. Take a
short ride. Adjust the height of the handlebar, and the height and the tilt of the seat,
if necessary, for maximum comfort.
9
Assembly - Step 5: Charging the Battery
Remove the charger from the box, attached the power cord and insert that to any
wall outlet. Insert the plug at the end of the smaller cable into the charging terminal
of the battery and start charging. The charging terminal is on the side of the battery
opposite to a hole on the side of the frame. The LED on the charger glows RED
while charging and glows GREEN when charging is complete. The battery should
be turned OFF while being charged. When the LED on the charger turns Green,
disconnect the charging cord and cover the charging terminal with the rubber cap.
If a battery is installed on the e-bike and turned ON, the display panel will show the
charge level of the battery when the bike turned ON.
You are now ready to start using your e-bike.
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels ENGWE-BIKES Vélo
