EnGenius EWS500AP Manuel utilisateur

Quick Installation Guide

EnGenius Europe | Veldzigt 28, 3454 PW De Meern,

Netherlands | 0900-WIFIABC | www.wiabc.com Disclaimer: Information may be subject to changes without prior notication. Follow us

https://www.linkedin.com/company/engeniuseurope

https://plus.google.com/+EngeniusEuropeBVDeMeern

https://www.youtube.com/user/engeniuseuropebv

https://twitter.com/engeniuseu

EWS500AP

Package contents

- Managed indoor access point

- Power adapter

- RJ-45 Ethernet cable

- Mounting bracket

- Mounting kit

- T-Rail mounting kit

Minimum requirements

- Broadband Internet service (Cable or DSL modem)

- Internet browser (Internet Explorer, Safari, Firefox, Chrome)

- EnGenius wireless management L2 switch (To use with EWS-series

management switches)

Connecting the access point

Step 1: Connect one end of a RJ-45 Ethernet cable to the PoE In (LAN/Uplink)

port on the rear of the access point.

Note: DO NOT connect a PoE injector to any of the four access ports on the

front as this could cause damage to the device.

Step 2: Connect the other end of the cable to a PoE Ethernet switch or the PoE

‘PoE Out’-port on the PoE injector.

Step 3: Using another RJ-45 Ethernet cable, connect one end to the Ethernet port

on the computer, and connect the other end to another port on the PoE Ethernet

switch or to the ‘Data In’-port on the PoE injector.

Step 4: Verify that the Power LED on the access point is steady orange.

Note: The access point supports both IEEE 802.3af/at PoE

(Power-over-Ethernet) or an optional DC power adapter (sold separately). You

may use either one as the power source. DO NOT use both at the same time.

IP adress configuration

Step 1: Once your computer is on, ensure that your

TCP/IP is set to ‘On’ or ‘Enabled’. ‘Open Network

Connections’ and then click ‘Local Area Connection’.

Select ‘Internet Protocol version 4 (TCP/IPv4)’.

Step 2: If your computer is already on a network,

ensure that you have set it to a static IP address on

the interface. (Example: 192.168.1.10 and the

subnet mask address as 255.255.255.0.)

Management switch setup

Step 1: Open a web browser on your computer.

In the adress bar of the web browser, typ in 192.168.1.1 and choose Enter.

Step 2: A login screen will appear. By default, the username is admin and

the password is admin. Enter the current username and password of the

wireless management switch and then click ‘Login’.

Step 3: The EnGenius wireless management switch user interface will appear.

This device can operate in access point mode.

Quick Installation Guide

EnGenius Europe | Veldzigt 28, 3454 PW De Meern,

Netherlands | 0900-WIFIABC | www.wiabc.com Disclaimer: Information may be subject to changes without prior notication. Follow us

https://www.linkedin.com/company/engeniuseurope

https://plus.google.com/+EngeniusEuropeBVDeMeern

https://www.youtube.com/user/engeniuseuropebv

https://twitter.com/engeniuseu

EWS500AP

Mounting the access point

This access point is designed to be mounted on a wall plate or electrical outlet

box.

Step 1: Remove the cover of the wall plate.

Step 2: Gently pull the required cables through the center of the

mounting bracket.

Step 3: Align the mounting bracket to the wall plate and affix the mounting

bracket to the using the original cover screws.

Step 4: Connect the cables to the access point before mounting to the bracket.

Step 5: Hook the two tabs on the bottom of the bracket into the slots on the

bottom of the access point, and slide the access point down gently until it holds

in place.

Step 6: Use the bracket screw provided to secure the access point to

the bracket.

Quick Installation Guide

EnGenius Europe | Veldzigt 28, 3454 PW De Meern,

Netherlands | 0900-WIFIABC | www.wiabc.com Disclaimer: Information may be subject to changes without prior notication. Follow us

https://www.linkedin.com/company/engeniuseurope

https://plus.google.com/+EngeniusEuropeBVDeMeern

https://www.youtube.com/user/engeniuseuropebv

https://twitter.com/engeniuseu

EWS500AP

Connecting using the 110 Punch-down block

The 110 punch-down block can be used to connect the access point to the

network instead of the RJ-45 connector.

Note: DO NOT connect to both the punch-down block and the PoE

(LAN/ Uplink) port to the network at a same time.

Table des matières

Autres manuels EnGenius Point d'accès sans fil

EnGenius

EnGenius EAP600 Manuel utilisateur

EnGenius

EnGenius EWS377AP Manuel utilisateur

EnGenius

EnGenius Neutron EWS210AP Manuel utilisateur

EnGenius

EnGenius EAP300 Manuel utilisateur

EnGenius

EnGenius ENH200EXT Manuel utilisateur

EnGenius

EnGenius EWS660AP Manuel utilisateur

EnGenius

EnGenius ENS202EXT Manuel utilisateur

EnGenius

EnGenius ENH Series Manuel utilisateur

EnGenius

EnGenius EAP1750H Manuel utilisateur

EnGenius

EnGenius EOC5611P Manuel utilisateur

EnGenius

EnGenius ECB7510 Manuel utilisateur

EnGenius

EnGenius Neutron EWS320AP Manuel utilisateur

EnGenius

EnGenius EOC1650 Manuel utilisateur

EnGenius

EnGenius ECB1200 Manuel utilisateur

EnGenius

EnGenius ENH202 Manuel utilisateur

EnGenius

EnGenius ENH500 Guide de configuration

EnGenius

EnGenius 11N Wireless Gigabit Multi-Function Client... Manuel utilisateur

EnGenius

EnGenius ENS202 Manuel utilisateur

EnGenius

EnGenius ECB3500 Manuel utilisateur

EnGenius

EnGenius EMD2 Manuel utilisateur

EnGenius

EnGenius EOC5510 Manuel utilisateur

EnGenius

EnGenius ENS200 Manuel utilisateur

EnGenius

EnGenius EWS850AP Manuel utilisateur

EnGenius

EnGenius EAP1750H Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur

Draytek

Draytek VIGORAP 902 Manuel utilisateur