-06-
-05-
-04-
INSTALLATION INSTRUCTIONS
Wakeup command class
The motion sensor will send a wakeup notification command if it has
been added into a Z-Wave network. The motion sensor will wake up
periodically(default is 30 minutes) as desired depending on time interval
command unless configured for another time interval. The motion sensor
you set from wakeup command class and resend the wakeup notification
will stay awake for 10 seconds and then go back to sleep to conserve
battery life. It will also go to sleep when receives command WAKEUP_
_NO_MORE_NOTIFICATION. The motion sensor can be woken up
manually: press and hold the program switch for one second, when
release the switch it will send broadcast wakeup notification or single-
-cast wakeup notification to associated devices.
Configuration command class
Configuration parameter can be used to adjust the delay time of sending
Parameter number 0
Parameter Size 1
Valid value 0-255
0: Not send basic set off
1-240: N minutes
241-255: 15 seconds
basic set off command after motion sensor sends the basic set on when
motion detected.
Battery command class
ZWN-BPC will check the battery power level every day and report the
Association command class
ZWN-BPC can control devices by using this command class and
battery level by sending broadcast BATTERY_REPORT. When battery
level goes down to 1%, it will send broadcast low power warning
command (BATTERY_REPORT, value 0xFF). User needs to replace
new batteries.
COMMAND_CLASS_BASIC. If a device is associated by ZWN-BPC,
the motion sensor will send basic set on/off to it when motion detected.
ZWN-BPC only supports one group with 5 nodes association.
Adding to Z-Wave network
At the back of Motion Sensor, there is a program button which is used
OPERATION
to add/delete and associated with other Z-Wave devices.
WARRANTY INFORMATION
Cannot carry out adding, deleting or association
1. Check to see if the battery is running out.
2. Make sure the battery is in right place.
3. Check if the wireless distance is too far
Cannot control the connected modules
The sensor does not working
TROUBLESHOOTING
3. Look for any nearby source of infrared energy that may interface.
1. Check to see if the battery is running out.
2. Check if the wireless distance is too far.
1. Check to see if the battery is running out.
2. Check if the wireless distance is too far.
Specification for WAKEUP_INTERBAL_SET:
0x000000-0x0000EF, 0x015181-0xFFFFFF, these values will be ignored.
ADVANCED FEATURE
Test mode
This is designed for users to test the PIR function. When ZWN-BPC
is in test mode, it will be awake for 15 seconds. Users can make any
movement to check whether the PIR function works. If ZWN-BPC
detects movement, the red LED will blinks.
Node Information Frame).
1. Switch a Z-Wave controller into inclusion mode.
2. Press and release the program button
ceiling sensor into learn mode(send NIF,
of ZWN-BPC will cause the
Inclusion
3. If success , red LED lit up for 5-second,and then turn off.
Note: If the ceiling sensor is not included in Z-Wave network,
button pressed.
red led will blink three time when power applied or program
Node Information Frame).
1. Switch a Z-Wave controller into exclusion mode.
2. Press and release the program button
ceiling sensor into learn mode(send NIF,
of ZWN-BPC will cause the
3. If success , red LED will turn off immediately.
Exclusion
Association
To complete Z-Wave association, please refer to your controller's
manual . Each controller has its own association method. If your
controller needs sensor to wake up, please press and hold the
program button for 2-second, then release,the ZWN-BPC will wake
up manually.
Note: If the motion sensor is not added in Z-Wave network,
button pressed.
program LED will blink three time when power applied or program
Deleting
Association
To complete Z-Wave association, please refer to your controller's
manual . Each controller has its own association method. If your
controller needs sensor to wake up, please press and hold the
program button for 1 second, the ZWN-BPC will wake up manually.
Note : Removing device from the network, the value of data will be reset.
Mar, 2014
Our company warranties this product to be free of defects in materials
and workmanship for a period of two(2) years.There are no obligations
or liabilities on the part of our company for consequential damages arising
out of, or in connection with, the use or performance of this product or
other indirect damages with respect to loss of property, revenue or
profit, or cost of removal, installation or reinstallation.
0x0000F0 Minimum value (Equal to 240 seconds)
0x015180 Maximum value (Equal to 68400 seconds, or 24 hours)
0x000708 Default value (Equal to 1800 seconds, or 30 minutes)
2. Press and release the program button located at the back of motion
3. Program LED will stay solid for 5 seconds and turn off when succeeds.
sensor to add it into your Z-Wave network and send Node Information
4. If the LED never light on and adding mode times out, then repeat the
adding process again and delete it if necessary.
1. Set a Z-Wave controller into adding mode.
Adding
Frame.
1. Set a Z-Wave controller into deleting mode.
sensor to delete it into your Z-Wave network and remove Node
Information Frame.
3. Program LED will blink 3 times after press the program button, that
means it is not in any Z-Wave network.
2. Press and release the program button located at the back of motion
For some controller, after configuration and association setting, please
wake up ZWN-BPC manually by pressing the program button.
11036A
