ENERMAX UC-9FATR2 Manuel utilisateur
１
Index
English Version 2-10 pages
Japanese Version 11-19 pages
２
1. Introduction
1.1 Product illustration
1.2 Package contents
The package should contain the following items:
1. The Multi-function Panel x 1（including 1 power
connector, 1 card reader connector and 2 sensor
wires）
2. Serial ATA cable x 2
3. USB transfer cable x 1 (2 ports)
4. USB cable ×1 (for directly linking to M/B)
5. IEEE1394 transfer cable x 1
6. IEEE1394 cable×1 (for directly linking to M/B)
7. Fan extension wires x 2
8. Accessory kit bag x 1
9. L type bracket
10. User’s manual
11. Driver CD
English Version
3
Specification:
Device space 5.25” drive bay
DC input +5V / +12V, USB bus power
DC output 4V – 12V DC
Temperature display range 0~90 ° C / 0~194 °F
Fan speed monitoring range 1000~9900 RPM
Fan header （3 pin）2
Wire of sensors 2
Power connector 4 pin
Card reader connector 4 pin
Brightness & fan speed
controllor
2
Compatible memory card CF I / II, SD, MMC, MS, SM, MD
Card reader Interface USB 2.0
OS Win 98SE/2000/ Me /XP, Mac OS 8.6+
Product dimen （）
sion D*W*H 149mm*72mm*41.5mm
4
2.Product Features
2.1 7 in 1 card reader:
2.1.1 Compatible cards:
1. Compact Flash Type I
2. Compact Flash Type II
3. IBM Micro Drive
4. Memory Stick、Memory Stick Duo、Memory Stick
PRO、Memory Stick Duo PRO
5. Smart Media
6. Secure Digital
7. Multi Media Card
5
2.2 Thermal controller module:
2.2.1 Thermal controller setup
a. Fan RPM (brightness control) setting:
Clockwise: increase the RPM (brightness).
Counterclockwise: decrease the RPM (brightness).
b. Overheat temperature degree setting:
H : 65 °C / 149 °F
M: 55 °C / 131 °F
L : 45 °C / 113 °F
c. Temperature unit and low fan speed alarm setting：you
can use enclosed jumps to cap on Jump pin to change
the temperature unit or fan speed RPM alarm setting.
c.1 JP1 for Temperature unit:
Open: OC Short:
OF
c.2 JP2 for fan speed alarm setting:
Open: 1000 RPM Short: 2000RPM
6
d. Hardware temperature and fan speed alarm display
switch：push “MODE” button to shift the display for the
first set “T1 F1” and the second set “T2 F2”
Note: Please press “Reset” button after setting
for completing the setting step.
2.2.2 LCD function description
1.Temperature display range: 0~90 °C / 0~194 °F
2.Fan speed monitoring range: 1000~9900 RPM
3.Overheat temperature alarm:
When the temperature is higher than setting value,
the digits on LCD starts flashing and buzzer starts
beeping. Audio alarm will automatically stop in 30
seconds once the cause resulting in over
temperature is removed. However, digits on LCD will
keep flashing till the cause is completely eliminated.
4.Fan low / fan failure alarm:
When fan speed is lower than the setting value,
digits on LCD starts flashing and buzzer starts
beeping. The beeping will automatically stop in 30
seconds even though the cause is left unsolved.
However, the digits on LCD keep flashing till the
cause is completely eliminated.
5.The fan speed will not display if the fan is not
connected.
7
3.Installation
3.1 The PCB illustration
3.2 The PCB connectivity illustration
Sensor SATA Card reader FAN Power IEEE1394 USB
8
3.3 The installation Steps
1. Insert the drive into 5.25” drive bay
2. Two connectivity options for USB & IEEE1394：
2-1 Directly linking to M/B
2-1-1 Attach the USB cable & IEEE1394 cables into
USB & IEEE1394 pin header of the M/B.
2-1-2 Attach the USB & IEEE1394 cables into PCB pin
header.
Note：Make sure the position accurate by "UP" label
2-2 Transferring from back panel I/O of PC--Insert the USB &
IEEE1394 transfer cables into the ports in the rear of PC
through the opening of enclosed L type bracket.
3. Attach the fan extension wires to PCB & fans you want to
monitor and control
4. Attach the 4-pin card reader cable into the USB pin header
on M/B
5. Attach the SATA cable connector to motherboard & PCB.
6. Attach sensors to hardware you want to monitor with
enclosed stickers.
9
4.Driver installation
4.1 Minimum System Requirements:
a. Windows
Pentium class PC with USB support
Windows 98SE, 2000, ME, XP
CD-ROM drive
USB 2.0 port required from Hi-Speed transfer
b. Macintosh
Macintosh computer with USB support
M a c O S 8 . 6 +
CD-ROM drive
USB 2.0 port required from Hi-Speed transfer
4.2 Installation for Windows 98/SE/2000
1. Insert the driver CD into the CD-ROM drive.
2. Click the CD-ROM drive icon.
3. Follow the steps of "Install Wizard" to install the "USB
Card Reader Driver".
4. Click "Yes" to reboot the system.
5. Plug your card reader connector into USB port and
Windows will detect it automatically.
a. The pop-up window "Find new Hardware" will
come out.
b. Wait for Windows to configure the card reader.
When the installation (of the card reader driver)
is successful, this pop-up window will
disappear automatically.
c. Open "my computer”. You’ll see removable
drives installed in your computer then the
installation is completed.
Table des matières
Autres manuels ENERMAX Contrôleurs
