WARRANTY INFORMATION
This device is warranted to be free of material and workmanship defects for 2 years from the
date of purchase. Original receipt or proof of purchase from an authorized retailer must be
presented upon warranty claim. ALL claims must be verified and approved by Enerlites, Inc.
Warranties from other Enerlites products may vary. This warranty is nontransferable and does
not cover normal wear and tear or any malfunction, failure, or defect resulting from misuse,
abuse, neglect, alteration, modification, or improper installation. To the fullest extent permitted
by the applicable state law, Enerlites shall not be liable to the purchaser or end user customer
of Enerlites products for direct, indirect, incidental, or consequential damages even if Enerlites
has been advised of the possibility of such damages. Enerlites’ total liability under this or any
other warranty, express or implied, is limited to repair, replacement or refund. Repair,
replacement or refund are the sole and exclusive remedies for breach of warranty or any other
legal theory.
456
© 2016 Enerlites Inc.
CA, U.S.A.
WWW.ENERLITES.COM
0206160018-01
DELETING a Program:
•Press PROG button until the ON or OFF program you wish to delete
is displayed.
•Press the MODE button. The program is now deleted. Remember to
delete each OFF program for every ON program and vice versa.
•When you are done deleting the undesired programs, press the MAN
button or close the switch door to return to the main screen.
Reseting the Timer:
To reset the Timer back to Factory Default Settings, use a small object
such as paper clip or the tip of a pen and press and release the "R" button
located just below the LCD Screen. The display will flash indicating a reset.
SELECT THE OPERATING MODE
The Digital Timer has 2 operating modes:
Manual (MAN) and Automatic (AUTO). To
switch modes, open the control panel door
and press the MODE button until the desired
mode is displayed.
Automatic Mode
On the main screen, "AUTO" mode will be
displayed when switch is in AUTO mode along
with the current state of the Load (ON or OFF).
In this mode, the Timer WILL turn the lights
ON/OFF according to the programmed times
regardless of whether the Load is ON or OFF.
Manual Mode
On the main screen, "MAN" mode will be
displayed when switch is in MANUAL mode
along with the current state of the Load (ON or
OFF). In this mode, the Timer WILL NOT turn
the lights ON/OFF
PROGRAMMING
NOTE:
•This Timer has a built in rechargeable battery backup. The
programming will be stored during the event of a power outtage.
•In programming mode, there is a 10 second time-out. If no keys are
pressed within 10 seconds, the display will return to main screen.
•The switch displays the time in 12-hour format.
Power-On
Programming
•Open the switch door from the right.
•Switch the Power switch to ON.
•Reset the switch using a small object such as paper clip or the tip of a
pen and press and release the "R" button located just below the LCD
Screen. The display will flash indicating a reset.
Setting the Clock
•Press the PROG button Once and the CLK icon will appear on the
bottom left of the screen.
•Set the time using the HOUR and MIN buttons, Ensure that P (for PM)
appears on the screen when an afternoon time is displayed.
•Set the day by using the DAY button.
•Press one of the MAN buttons or close the switch door to return to the
main screen.
•Press the PROG button twice to display a program and its ON time. For
example, when you first press PROG twice from the main screen, program
number 1 and its ON time will appear. 1ON PROG - -:- - will appear
instead of the time if the program is not set (inactive).
•Press DAY button to select the day in which you want to apply to the
program.
oNOTE: if you want to apply the program to every day of the week,
press DAY until ALL the days are displayed. (This still counts as
1 program, not 7)
•Press the HOUR and MIN buttons to set the ON time (time when you want
the lights to turn on).
•After you have programmed the ON time, press the PROG button to
display the OFF time (time when you want the lights to turn off).
oNOTE: If the program ON time is set for every day of the week,
the program OFF time will have to be the same.
•To set another program, repeat steps 4 through 7. Programs that are not
set will remain inactive.
•Press one of the MAN buttons or close the switch door to return to the main
screen.
•To ensure the programming takes place, "AUTO" must be displayed on the
LCD screen.
MIN
4. PROG
5. MAN
1. LCD
SCREEN
2.
MODE
3. DAY
MAN
HOUR
PROG
MAN MAN
OFF ON
INDOOR
MO
OFF AUTO P
R
6. RESET
7. HOUR
8. MIN
9. POWER
DAY
MODE
HET01-C shown in diagram
