Encore Networks IBR-10 Manuel utilisateur

encor en

•etworksTM

Broadband Access Network Device for Intelligent Termination (BANDIT), Encore Legacy-to-IP Operating

System (ELIOS), and IP Banking Router 10 (IBR-10) are trademarks of Encore Networks, Inc. All other

trademarks are the properties of their respective owners.

See the VPN and Legacy-to-IP Products Customization and Maintenance Guide for Limitation of Liability.

IBR-10™ Installation Guide

for ELIOS™ Software Version 0500

his guide presents procedures for a standard installation of the IBR-10™.

Note: The screens shown in this document are examples; the choices shown on your IBR-10’s menus

depend on the features in the chassis and on the software version installed in the device. (For figures,

tables, and configurations not addressed in this Quick Installation Guide, see the VPN and Legacy-to-IP

Products Customization and Maintenance Guide or the VPN and Legacy-to-IP Products Hardware Reference

Guide.)

Gather all required information. Before you start these procedures, make sure you have all the information

required to set up the IBR-10 for use in your network—for example, the device’s IP address, the device’s

configuration, and network and routing functions that the device will perform. Use the site planning

worksheets in the VPN and Legacy-to-IP Products Customization and Maintenance Guide as checklists for this

information.

If you have questions or concerns after you have followed these procedures, contact Encore Networks, Inc.,

at [email protected], 703-318-4350 (voice), or 703-318-4371 (fax).

A Setting Up the Hardware

1Unpack the chassis and components from the shipping box. Make sure you have all the parts:

the chassis (Figure 1), an autosensing external power supply, an RJ-45 Supervisory cable, an adapter for

the Supervisory cable (described in the Note in Step 7), a paper copy of this Quick Installation Guide, a

CD containing customer documentation for the VPN and Legacy-to-IP products, and any additional

accessories that you ordered.

Note: Shipments within North America include a power cable. For shipments outside North America,

contact your distributor for a cable that meets local requirements to connect the BANDIT’s power

supply to a power outlet.

Figure 1. IBR-10 Chassis, Front

2Place the IBR-10 chassis on a tabletop or shelf.

3Connect an earth ground wire to the chassis, as follows: Attach a (minimum) 12 AWG wire to the earth

ground screw to the right of the safety ground symbol, on the extreme right rear of the chassis

(Figure 2). Use a ring terminal, such as an AMP (part number 36160), for this connection.

Revision A, May 2004

Document Part Number 15736.0001

2IBR-10™ Installation Guide

Warning: An earth ground must connect to the chassis so that the device remains grounded

even when it is not receiving power.

Figure 2. IBR-10 Chassis, Rear

4Connect the IBR-10’s ports to their network devices.

5Connect the chassis to the external power supply.

6Then connect the external power supply to an outlet supplying 100–240 VAC at 47–63 Hz.

7Use the Supervisory cable and adapter to connect the device’s Supervisory port to your PC’s COM

port.

Note: An eight-pin modular (RJ-45) to DB-9 adapter is the standard adapter to connect the

Supervisory cable to a PC. This adapter is shipped with the unit. The following alternate

adapters are also available. (Contact Encore Networks, Inc., if you need either of these adapters.)

• An RJ-45 to DB-25 adapter for connection to most asynchronous terminals

• An RJ-45 to DB-25 modem adapter to connect a modem for out-of-band management or remote

configuration

B Logging In

1On the PC, open a terminal emulation session, such as HyperTerminal. Use the settings in Table 1

to establish communication between the terminal console and the IBR-10.

2On the terminal console, press Enter to autoconnect to the attached device.

❖After successful log-in, the Main Menu appears.

Table 1. Supervisory Port Communication Settings

Parameter Value

Bits per second 9600

Data bits 8

Parity None

Stop bit 1

Flow control Hardware

IBR-10™ Installation Guide 3

C Using the Main Menu

The Main Menu is displayed when you log onto the IBR-10. From the Main Menu, you can configure

and operate the IBR-10.

Note: Whenever you wish to return to a higher level in the IBR-10 menus, press Escape.

Caution: The Supervisory connection to the device will time out after 5 minutes of console

inactivity. If you have changed the device’s configuration and wish to use the new configuration,

save (write) the configuration before you leave the console. (See Section E, Saving (Writing) the

Device’s Configuration.)

1On the Main Menu, do one of the following:

aFor a basic configuration of the IBR-10 for your network, select QuickStart Config Builders.

❖The Startup Config Options menu is displayed. You can enter basic information on this menu;

the IBR-10 will use this information to build a standard configuration. Go to Section D.1, Startup

Configuration.

Main Menu

----------

1) QuickStart Config Builder

2) Typical Configurations

3) Advanced Configurations

4) Tools

V) View Current Unit Status

L) Load Factory Defaults

P) Load Plug and Play Defaults

W) Write Configuration

R) Reset Unit

X) eXit Session

S) Statistics

Y) sYstem Administration

Enter Choice :

Startup Config Options

-----------------------

1) BANKING

Enter Choice :

4IBR-10™ Installation Guide

bTo configure specific features, select Advanced Configurations.

❖The Advanced Configurations menu is displayed. You configure most parameters of the

IBR-10 from this menu. Go to Section D, Configuring the Software.

D Configuring the Software

For a standard, basic configuration of the IBR-10 for your network, see Section D.1, Startup

Configuration. For configuration of specific features, see the following sections.

•Section D.2, Device Addresses

•Section D.3, Ports

•Section E.4, Virtual Private Network Connections

•Section D.4, IP Configuration

•Section D.5, Simple Network Management Protocol

D.1 Startup Configuration

The menu provides several templates for configurations that your network may use. You can select a

template (also known as a startup scenario), change the scenario’s IP addresses and related

information to reflect the values in your network, and load the scenario into the IBR-10.

Note: If you want the device to keep the configured scenario, be sure to write the configuration and

reset the device.

To configure a basic setup for this device in your network, do the following:

1On the Main Menu, select QuickStart Config Builders.

2On the Startup Config Options menu, select the Banking set of configuration templates.

❖The menu for Startup Configuration Scenarios appears.

Advanced Configurations

------------------------

1) Physical Configurations

2) Data Configurations

3) Local Address

4) Routing

5) Global Paths

Enter Choice :

IBR-10™ Installation Guide 5

3Select one of the listed set-ups.

❖The menu for the selected set-up (scenario) is displayed. (The menu shown is for Ethernet

WAN to Sync Poll Select.)

Note: At this point, all IP addresses, etc., have null values. Before you can load the configuration

into the IBR-10, you must enter values that reflect your network’s settings.

4For each item (parameter) in the menu, do the following:

aSelect the item (for example, LAN Interface IP).

bType a value for the item, and press Enter.

cIf the item requests additional information, enter that information.

❖When the item has been configured, the scenario’s menu is displayed again.

IBR-10

Startup Configuration Scenarios

---------------------------------------

1) Bisync ATM to Ethernet WAN IP

2) Ethernet WAN to Async Poll Select

3) Ethernet WAN to Sync Poll Select

4) Ethernet WAN to Bisync

5) WAN/Serial(PPP) Router

6) WAN/Serial(Frame Relay) Router

Enter Choice :

Startup Configuration Parameters

---------------------------------

1) System Name :

2) System IP Address : 0.0.0.0

3) WAN Interface IP : Dynamic

4) Serial Interface Sync Line Speed : 9600 Type: HOST

5) Local Poll Address :

6) Local Group Poll Address :

7) Remote IP Address (N.N.N.N) : 0.0.0.0

8) Local Transmission Numbers : Auto

9) Remote Connection Type : Cts1

A) Remote TCP Port (1024 - 65535) : 1024

L) Load Above Config

V) reView/Modify Loaded Config

R) Reset (Write and Reset)

Z) Clear All Fields

Enter Choice :

Enter IP Address :

6IBR-10™ Installation Guide

5After you have performed Step 4 for each item (parameter) in the menu, do one of the following:

aSelect Load Above Config.

❖The following prompt asks for confirmation. Go to Step 6.

bSelect Reset (Load, Write and Reset).

❖The following prompt asks for confirmation. Go to Step 6.

cSelect Clear All Fields.

❖The following prompt asks for confirmation.

• Do one of the following:

◆If you wish to reconfigure, enter Y.

❖All fields in the menu are reset to null values. Return to Step 4.

◆If you do not wish to reconfigure, press Escape to return to the Startup Configuration

Scenarios menu.

❖The configuration retains the settings you have entered, but they are not yet in use. Return

to Step 4.

6To load the new configuration, enter y.

❖The configuration is loaded into the IBR-10.

❖If you selected Reset (Load, Write, and Reset), the configuration is also saved. This makes the

configuration permanent (unless you change it again). Then the device resets.

7When the configuration has finished loading, press Escape until you return to the Main Menu.

(Go to Section C, Using the Main Menu.)

8To save the configured scenario (if it has not already been saved), do the following:

aWrite the configuration. (See Section E, Saving (Writing) the Device’s Configuration.)

bReset the BANDIT. (Section F, Restarting (Resetting) the Device.)

Caution: Existing configurations will be over written

Do you want to Continue?(Y/N)[N]:

Caution: Existing configurations will be over written

Do you want to Continue?(Y/N)[N]:

This Clears All the above Fields, Continue?(Y/N)[N]:

IBR-10™ Installation Guide 7

D.2 Device Addresses

To configure the device’s addresses, do the following:

1On the Advanced Configurations menu, select Local Addresses.

2On the Configure Local Addresses menu, select IP Address.

3Enter the device’s IP address and press Enter. (Get the device’s IP address from your network

administrator.)

4Select BANDIT Name.

5Enter a unique name to identify this device in your network, and press Enter.

D.3 Ports

To configure software for the device’s ports, do the following:

1On the Advanced Configurations menu, select Data Configuration.

❖The Logical Port Protocol menu is displayed. (Table 2 lists the Line IDs for the ports.)

Table 2. Port Identifiers

Line ID Physical (Hardware) Port Default Software Configuration

C COM/Supervisor port Comm/Supervisor a

L Ethernet LAN port Ethernet

S Serial port Frame Relay

PMoreportsb(See Step 2.)

a. Do not modify the configuration for the Comm/Supervisor port.

b. These are virtual Logical Ports. A protocol configured on a Logical Port can be

associated with a global path, which is turn is associated with a physical port. (See

Section D.3.1, Protocols. For information on global paths, see the VPN and Legacy-

to-IP Products Customization and Maintenance Guide.)

8IBR-10™ Installation Guide

2On the Logical Port Protocol menu, select the physical port whose software configuration you

wish to modify.

❖One of the following occurs:

• If you are configuring a physical port, the Logical Port Attribute menu appears. Go to Step 4.

• If you are configuring a virtual Logical Port, the Virtual Logical Port menu is displayed.

Continue to Step 3.

3On the Virtual Logical Port menu, select the port to configure.

❖The Logical Port Attribute menu appears.

4To modify the port’s default settings, see the following:

•Section D.3.1, Protocols

•Section D.3.2, DHCP Settings (only for the WAN and LAN ports)

•Section D.3.3, Dial Backup Settings

D.3.1 Protocols

To change the protocol that a port uses, or to modify attributes of a port’s protocol, do the following

on the Logical Port Attribute menu (see Section D.3, Ports):

1If you wish to change the protocol the port uses, do all of the following:

aSelect Undefine Current Logical Port.

bSelect Protocol.

cOn the Logical Port Protocol Selection menu, select the protocol you want this port to use. Go

to Step 2a.

IBR-10

Logical Port Protocol Mapped To Port Interfaces

------------------------------------------------------------------------

1) UNDEFINED

2) UNDEFINED

3) UNDEFINED

4) UNDEFINED

5) UNDEFINED

6) UNDEFINED

7) UNDEFINED

8) UNDEFINED

9) UNDEFINED

10) UNDEFINED

11) UNDEFINED

12) UNDEFINED

13) UNDEFINED

14) UNDEFINED

15) UNDEFINED

16) UNDEFINED

17) UNDEFINED

P) More Ports...

Enter Port :

IBR-10™ Installation Guide 9

2To modify parameters in the port’s protocol, select Protocol.

❖The protocols available for the port are displayed. (This example shows protocols for a serial

port, available in models that support legacy protocols.)

aOn the protocol configuration menu, select and change parameters to work in your network.

bWhen you have finished configuring the protocol, press Escape to return to the Logical Port

Attribute menu.

D.3.2 DHCP Settings

To review settings that the WAN or LAN port uses for DHCP, or to modify or disable DHCP on a port,

do the following on the port’s Logical Port Attribute menu (see Section D.3, Ports).

Note: The WAN and LAN ports use different settings. Typically, a BANDIT device is a DHCP client

on the WAN port and is a DHCP server on the LAN port. You may enable, modify, or disable use of

DHCP on one port or on both ports.

1Select DHCP Type.

❖The DHCP Type menu appears.

Logical Port Protocol Selection Menu

-------------------------------------

1) Frame Relay

2) Point-to-Point (PPP)

3) MultiLink PPP

4) X.25+

5) SDLC Routing

6) SDLC 1490 Configuration

7) Bit Sync Encapsulation

8) Asynchronous Encapsulation

9) Serial Line IP (SLIP)

A) Async Burroughs Poll/Select

B) Sync Burroughs Poll/Select

C) Bisync

D) Telnet Terminal

E) XXX PAD

Enter Choice :

DHCP Type

----------

1) Server

2) Client

3) None

Enter Choice :

10 IBR-10™ Installation Guide

2Select the option you want this port to use.

❖If you select None, the device does not use this port for DHCP. Press Escape until you return

to the port’s Logical Port Attribute menu. Go to Step 5.

❖If you select Client, the device uses this port to request its IP address. (On the WAN port, the

device requests its public IP address.) No further configuration is required for the DHCP client

role. Press Escape until you return to the port’s Logical Port Attribute menu. Go to Step 5.

❖If you select Server, the device uses this port to assign IP addresses. (On the LAN port, the

device assigns private IP addresses.) The Logical Port Attribute menu is redisplayed, with a menu

item for configuring the DHCP server.

3Select DHCP Server Parameters.

❖The DHCP Server Parameters menu appears.

4Select and configure each parameter the device will use as the local (intranet) DHCP server. When

you have finished configuring the DHCP server, press Escape until you return to the port’s

Logical Port Attribute menu.

5When you have finished configuring the port, press Escape until you return to the Main Menu.

6Save the configuration and reset the device. See Section E, Saving (Writing) the Device’s

Configuration, and Section F, Restarting (Resetting) the Device.

D.3.3 Dial Backup Settings

1To configure a port for dial backup, select Dialup Configuration on the Logical Port Attribute

menu (see Section D.3, Ports).

Note: A port can be configured for dial backup only if its protocol supports dial backup. The

port’s Logical Port Attribute menu will not allow this option unless the protocol supports it. To

select a protocol that supports dial backup, see Section D.3.1, Protocols.

2Configure the parameters for the dialup. When you have finished, press Escape to return to the

Logical Port Attribute menu.

D.4 IP Configuration

This section discusses additional IP considerations you must configure in order to use the IBR-10 as a

network gateway.

1On the Advanced Configurations menu, select Routing.

DHCP SERVER PARAMETERS

----------------------------

1) Local DHCP Server IP Address (N.N.N.N):0.0.0.0

2) DHCP Pool IP Address Low (N.N.N.N) :0.0.0.0

3) DHCP Pool IP Address High (N.N.N.N) :0.0.0.0

4) DHCP Network Mask (N.N.N.N) :255.255.255.0

5) DHCP Lease Time (minutes) : 1440

6) Domain Name for DHCP clients:

7) Primary Router (N.N.N.N) :0.0.0.0

8) NETBIOS Server (N.N.N.N) :0.0.0.0

Enter the number of the item to change:

Table des matières

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur