EN SpinCycle Manuel utilisateur
SpinCycle
Rotating Speaker Emulator
User’s Manual
Copyright © 2014 Experimental Noize, All Rights Reserved
Experimental Noize | www.xnoize.com | support@xnoize.com
Table of Contents
1. Introducon..........................
2. Top Panel................................
3. Rear Panel...............................
4. Typical Connecon................
5. Footswitch Wiring.................
6. FCC Regulaon.....................
7. Warranty Informaon........
2
3
6
7
9
10
11
SpinCycle
Thank you for choosing the SpinCycle rotang
speaker emulator from Experimental Noize. This
unit has been designed to both accurately
emulate a rotang speaker as well as giving the
user the ability to adjust the sound in order to
meet their requirements.
Experimental Noize | Los Angeles, CA USA | xnoize.com
INTRODUCTION
2
Experimental Noize | Los Angeles, CA USA | xnoize.com
TOP PANEL
3
Slow Speed: Sets the slow speed of the rotaon emulaon;
the Speed push buon selects between the
slow and fast sengs.
Fast Speed: Sets the fast speed of the rotaon emulaon;
the Speed push buon selects between the
slow and fast sengs.
Acceleraon: Sets the rate at which the transion between
Experimental Noize | Los Angeles, CA USA | xnoize.com 4
TOP PANEL
the slow and fast speeds happen.
Also affects the speed at which the
emulator comes to a stop when the brake
buon is pressed.
Drum:Rotor Rao: On many rotang speakers, the drum
and rotor are driven by separate motors.
While their speeds may be close, they are
not idencal; the drum is always a lile
slower than the rotor. The speed difference
between the two motors creates a “beat”
between the drum and rotor that can be
unique to a parcular rotang speaker
cabinet. This control allows the user to
adjust the speed rao between the drum
and rotor to emulate this difference in
motor speeds.
Tube Emulaon: Increasing this control increases the
amount of tube emulaon, from a clean to
an asymmetric tube compression sounds.
Cab Emulaon: This control allows the user to enable and
adjust the cabinet emulaon. Part of what
gives the spinning speaker its unique sound
is the cabinet; this control emulates the
frequency response and reflecons that in
the cabinet and allows the user to adjust
the level of the emulaon.
Experimental Noize | Los Angeles, CA USA | xnoize.com
5
TOP PANEL
Distance: Adjusts the distance of the virtual microphones
from the cabinet. Closer will give a very heavy
“throbbing” sound, while further away will
give a more subtle sound.
Balance: Adjusts the balance between the rotor and
drum sounds.
Enable: This switch will enable/disable the effect. When
enabled the blue LED above the switch will be
lit.
Brake: This switch, when pressed, will slow the spinning
emulaon to a complete stop. Releasing the
switch will allow the emulaon to speed back
up to the set speed.
Speed: This switch selects between the slow and fast
speed sengs. The LED above this switch will
blink at the current rotaon speed.
Experimental Noize | Los Angeles, CA USA | xnoize.com 6
REAR PANEL
This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any
interference received, including
interference that may cause undesired
operation.
Made in Taiwan
PA01A00001R01
2014
9V DC: Power adapter input. Use only approved adapters.
Footswitch: Input for remote footswitch to control the
Enable and Speed switches remotely. If plugged
in, the footswitch will override the pedal
switches.
Mono In: Instrument input, typically from an electric
guitar or keyboard.
+Gain: This switch provides 12dB of gain to the input.
Typically used with electric guitars that have a
low output level; generally not required with
instruments such as keyboards.
Right Out: Right channel output.
Le Out: Le channel output.
Experimental Noize | Los Angeles, CA USA | xnoize.com
7
This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any
interference received, including
interference that may cause undesired
operation.
Made in Taiwan
PA01A00001R01
2014
Step 1: Connect the instrument to the Mono In jack. If
using a low signal level instrument, such as an
electric guitar, press the +Gain switch so that it is
in the in posion.
Step 2: Connect the Right Out and Le Out to a pair of
amplifiers, or a stereo amplifier.
TYPICAL CONNECTION
Experimental Noize | Los Angeles, CA USA | xnoize.com 8
TYPICAL CONNECTION
Step 3: Plug in the power adapter to the pedal and to a
mains power plug.
Step 4: Play!
Experimental Noize | Los Angeles, CA USA | xnoize.com
9
This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any
interference received, including
interference that may cause undesired
operation.
Made in Taiwan
PA01A00001R01
2014
This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any
interference received, including
interference that may cause undesired
operation.
Made in Taiwan
PA01A00001R01
2014
FOOTSWITCH WIRING
FAST/SLOW ENABLE
Tip: Fast/Slow Ring: Enable Sleeve: Common
The switches should be single-pole/single-throw on/off
type switches, not momentary switches.
Table des matières
Manuels Équipement d'enregistrement populaires d'autres marques
Strymon
Strymon NIGHTSKY Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuel utilisateur
Tews Technologies
Tews Technologies TPMC465 Manuel utilisateur
Honeywell
Honeywell Excel 50 Manuel utilisateur
SeaLevel
SeaLevel COMM+8.LPCI Manuel utilisateur
Arturia
Arturia AUDIOFUSE STUDIO Manuel utilisateur
