Emulex LPe15004-Series Manuel utilisateur

P008875-03A Rev. A Connect • Monitor • Manage

LPe15004, LPe16004, and

LPe16000B-Series Adapters

Installation Manual

LPe15004, LPe16004, and LPe16000B-series HBA Installation Manual P008875-03A Rev. A

means or translated to any electronic medium without the prior written consent of Emulex.

Information furnished by Emulex is believed to be accurate and reliable. However, no responsibility is assumed by

Emulex for its use; or for any infringements of patents or other rights of third parties which may result from its use. No

license is granted by implication or otherwise under any patent, copyright or related rights of Emulex.

Emulex, the Emulex logo, Emulex BladeEngine, Emulex InSpeed, Emulex LightPulse, Emulex OneCommand, Emulex

OneConnect, and SLI are registered trademarks, and Emulex Advanced-8, Emulex Connect, Emulex CrossLink,

Emulex Engine, Emulex Edge, Emulex ExpressLane, Emulex GreenState, Network Xceleration, Emulex OneCore,

Emulex Pilot, Emulex SURF, Emulex Universal Multi-Channel, Emulex vEngine, Emulex Virtual Fabric, Emulex

Virtual Network Exceleration, Emulex vPath, Emulex vScale, AutoPilot, AutoPilot Installer, and BlockGuard are

trademarks, of Emulex. All other brand or product names referenced herein are trademarks or registered trademarks

of their respective companies or organizations.

Emulex provides this manual "as is" without any warranty of any kind, either expressed or implied, including but not

limited to the implied warranties of merchantability or fitness for a particular purpose. Emulex may make

improvements and changes to the product described in this manual at any time and without any notice. Emulex

assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties that may

result. Periodic changes are made to information contained herein; although these changes will be incorporated into

new editions of this manual, Emulex disclaims any undertaking to give notice of such changes.

Emulex, 3333 Susan Street

Costa Mesa, CA 92626

Table of Contents 3

LPe15004, LPe16004, and LPe16000B-series HBA Installation Manual P008875-03A Rev. A

Table of Contents

List of Figures ......................................................................................4

List of Tables .......................................................................................5

1. Introduction.....................................................................................6

Overview................................................................................................6

Major Features ....................................................................................6

Compatibility......................................................................................7

Prerequisites.......................................................................................7

Adapter Identification ...........................................................................7

2. Installation.......................................................................................8

Preparing the Adapter for Installation............................................................8

Installing the Adapter .............................................................................. 10

Attaching Media ..................................................................................... 11

Applying Power ...................................................................................... 13

Viewing the LEDs.................................................................................... 13

POST Conditions and Results...................................................................13

3. References ....................................................................................15

LPe15004, LPe16004, and LPe16000B–Series Adapter Specifications ................... 15

FCC and Regulatory Notices....................................................................... 16

Declarations of Conformity........................................................................ 18

Laser Safety Notice ................................................................................. 20

List of Figures 4

LPe15004, LPe16004, and LPe16000B-series HBA Installation Manual P008875-03A Rev. A

List of Figures

Figure 2-1 Typical Optical Transceiver ..............................................................8

Figure 2-2 Releasing the Latch on an Optical Transceiver........................................9

Figure 2-3 Removing an Optical Transceiver........................................................9

Figure 2-4 Removing the Bracket....................................................................10

Figure 2-5 Installing an Optical Transceiver .......................................................12

Figure 2-6 Connecting a Fiber Optic Cable.........................................................12

Figure 2-7 Optical Adapter LED Indicators .........................................................13

List of Tables 5

LPe15004, LPe16004, and LPe16000B-series HBA Installation Manual P008875-03A Rev. A

List of Tables

Table 1-1 Software and Hardware Environments..................................................7

Table 2-1 Media Specifications......................................................................11

Table 2-2 POST Conditions and Results ............................................................14

Table 3-1 LPe15004, LPe16004, and LPe16000B–series Adapter Specifications..............15

1. Introduction

Overview 6

LPe15004, LPe16004, and LPe16000B-series HBA Installation Manual P008875-03A Rev. A

1. Introduction

Overview

This manual describes the following Fibre Channel (FC) to Peripheral Component

Interconnect Express (PCIe) Emulex® host bus adapters:

LPe15004, 8 gigabit per second (Gbps)

LPe16000B, LPe16002B, and LPe16004, 16 Gbps

The core technology of these adapters is Emulex's 10th generation FC controller. The

controller is a multi-function PCIe Gen3 interface controller that is compliant to the PCI

Express Base Specification Rev 3.0 and PCI Express CEM Specification Rev 3.0. The

LPe16000B is a single-channel adapter, the LPe16002B is a dual-channel adapter, and

the LPe15004 and LPe16004 are four-channel adapters.

These adapters support packet transfers at 2.5, 5.0, and 8 gigatransfers per second (2.5,

5.0, and 8 GTps) on the PCIe link (auto-negotiated with the system). The supported

physical PCIe connector is x8. The fully featured FC port is compliant to various

American National Standards Institute (ANSI) FC standards.

Note: Illustrations in this manual are only examples. The actual hardware may vary.

Major Features

Multi-function PCIe 3.0 device with one (LPe16000B), two (LPe16002B), or four

(LPe15004 and LPe16004) independent FC ports.

Auto-negotiation between 4-Gbps, 8-Gbps, or 16-Gbps (LPe16000B, LPe16002B,

and LPe16004 adapters only) FC link speeds.

Complies with the PCIe base and CEM 3.0 specifications.

x8-lane standard Generation 3, PCIe interface at 2.5GTps, 5GTps, or 8GTps

(auto-negotiated with the system).

ECC protection of high density RAM (single-bit correction, double-bit

detection).

SFP+ interface supporting optics with LC connections and digital diagnostics

capability.

Host interface support is provided through Emulex standard drivers.

The LPe15004 adapter supports Windows Server 2008, Windows Server

2012, Windows Hyper-V, Citrix, Kernel-based Virtual Machine (KVM),

VMware ESXi, Red Hat Enterprise Linux (RHEL), SUSE Linux Enterprise

Server (SLES), Oracle Enterprise Linux (OEL), and Solaris S11 (x86 and

Solaris Sparc)

The LPe16000B-series adapters supports Windows Server 2008 R2 and

Windows Server 2008, Red Hat Enterprise Linux, VMware ESXi, and Solaris

S11 (including Comstar).

1. Introduction

Overview 7

LPe15004, LPe16004, and LPe16000B-series HBA Installation Manual P008875-03A Rev. A

The LPe16004 adapter supports Windows Server 2008 R2, Windows Server

2012, Linux 2.6 Kernel, VMware ESXi, Solaris 11 (including Comstar), Target

Mode Drivers (TM Kits 9.6 and 9.7), FreeBSD, and Debian.

Note: Windows Server 2008 and 2008 R2 support drivers written for these

adapters; however, new features designed for 10.6 drivers are not supported

for these operating systems.

Parts and construction are compliant to the European Union Directive of

Restriction of Hazardous Substances (RoHS).

Compatibility

Prerequisites

Use PCIe Gen 3 compliant systems that are x8 or x16 lane at up to 8 GTps per lane.

Adapter Identification

Each adapter ships with several numbers clearly marked on the board. Emulex

recommends recording these numbers before installation.

Serial number – assigned by Emulex. Use this number when communicating

with Emulex.

IEEE address – an Institute of Electrical and Electronics Engineers (IEEE) unique

64-bit identifier used for system configuration

World Wide Name (WWN) – derived from the IEEE) address, the FC industry

uses the WWN for FC connectivity.

Note: IEEE addresses and WWNs are assigned in sequential order. For example, if

an adapter has four ports, it has four IEEE addresses and four WWNs; one

for each port with the second, third and fourth IEEE addresses/WWNs

being the next successive number of the first.

Table 1-1 Software and Hardware Environments

Software Environments See the adapter’s website for compatible operating systems.

Hardware Environments LPe15004: PCIe 3.0 supports x8, x4, x2, and x1.

LPe16004, LPe16000B, and LPe16002B: PCIe 3.0 supports x8, x4, and

x1.

Note: Adapters are PCIe 3.0 and CEM 3.0 compliant systems and are

backwards compatible to 1.0a, 1.1, and 2.0 compliant

systems.

2. Installation

Preparing the Adapter for Installation 8

LPe15004, LPe16004, and LPe16000B-series HBA Installation Manual P008875-03A Rev. A

2. Installation

The standard adapters can be connected to fiber optic cables.

Preparing the Adapter for Installation

The Emulex LPe16004, LPe16000B, and LPe16002B adapters use removable optical

transceivers. If you need to change the bracket for an adapter installation, you must

first remove the optical transceiver(s), if installed, from the housing (cage). This

procedure explains how to remove the transceiver and bracket safely.

Notes:

The LPe15004 adapter comes with a low–profile PCIe bracket installed.The

low–profile mounting bracket is shorter than the standard bracket;

approximately 3.11 inches (7.9 cm) compared to 4.75 inches (12.06 cm) long.

On the LPe15004 adapter, you can remove and change the bracket but you

cannot remove the optical transceiver.

The LPe16004, LPe16000B, and LPe16002B adapters come with a standard

full–height PCIe bracket installed.

To change the bracket:

1. Some adapters have optical transceivers embedded in their cage assemblies. These

optical transceivers must be removed before the bracket can be removed. If the

adapter contains optical transceivers, continue with the following steps; otherwise,

proceed to step 4.

Caution: This is a delicate operation. Take care not to damage the optical

transceiver.

The adapter uses different types of optical transceivers. Figure 2-1 shows an

example of one type with the bail (handle) extended.

Figure 2-1 Typical Optical Transceiver

2. To remove a transceiver, pull the bail (handle) out and down to release the latch

and gently pull the transceiver out. Do not force it. After the latch is released, the

transceiver slides out easily.

2. Installation

Preparing the Adapter for Installation 9

LPe15004, LPe16004, and LPe16000B-series HBA Installation Manual P008875-03A Rev. A

Figure 2-2 shows a transceiver with the latch released (bail extended) and another

transceiver latched in place.

Figure 2-2 Releasing the Latch on an Optical Transceiver

Figure 2-3 shows an extracted transceiver and another transceiver latched in place.

Figure 2-3 Removing an Optical Transceiver

3. Observing Electrostatic Discharge (ESD) precautions, store the transceiver in an

ESD-safe place.

2. Installation

Installing the Adapter 10

LPe15004, LPe16004, and LPe16000B-series HBA Installation Manual P008875-03A Rev. A

4. Remove the mounting bracket screws from the top of the adapter. Figure 2-4 shows

the screws that are removed from the bracket.

Figure 2-4 Removing the Bracket

5. Remove the bracket and store it for future use.

6. Align the new mounting bracket tabs with the holes in the adapter.

Note: Be careful not to push the bracket past the EMI compression tabs of the SFP

cage. Ensure the light emitting diodes (LEDs) are properly aligned with the

holes in the bracket.

7. Re-install the screws that attach the adapter to the bracket.

8. Re-install the transceiver by sliding it into the housing. When the latch engages, it

clicks.

9. Push the bail back into place.

Installing the Adapter

To install the adapter:

1. Turn off the computer if hot-plug installation is not supported on the server.

See your server documentation to see if it supports Hot Plug/Hot Swap of PCIe

adapter cards.

2. Remove the computer case.

3. Remove the blank panel from an empty PCIe bus slot.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Emulex Adaptateur

Emulex

Emulex LP1050 Manuel d'installation et d'exploitation

Emulex

Emulex LP9002C Manuel d'installation et d'exploitation

Emulex

Emulex LP9002S Manuel d'installation et d'exploitation

Emulex

Emulex LP21000 Manuel utilisateur

Emulex

Emulex LP10000 Manuel d'installation et d'exploitation

Emulex

Emulex OneConnect OCe14000-Series Manuel utilisateur

Emulex

Emulex OneConnect OCe14000-Series Manuel utilisateur

Emulex

Emulex LP10000DC Manuel d'installation et d'exploitation

Emulex

Emulex LP952L Manuel d'installation et d'exploitation

Emulex

Emulex LP1005DC-CM2 Manuel utilisateur

Emulex

Emulex NC551i Manuel utilisateur

Emulex

Emulex LP10000ExDC Manuel d'installation et d'exploitation

Emulex

Emulex LPe1150 HBA Manuel utilisateur

Emulex

Emulex LP10000 Manuel utilisateur

Emulex

Emulex OneConnect OCe14000-Series Manuel utilisateur

Emulex

Emulex LP9802DC Manuel d'installation et d'exploitation

Emulex

Emulex LPe11002 HBA Manuel utilisateur

Emulex

Emulex LPe11004 HBA Instructions de montage

Emulex

Emulex LP1050DC Manuel d'installation et d'exploitation

Emulex

Emulex LP982 Manuel d'installation et d'exploitation

Emulex

Emulex LPE11000 HBA Manuel utilisateur

Emulex

Emulex LP1050Ex Manuel d'installation et d'exploitation

Emulex

Emulex AW520A Manuel utilisateur

Emulex

Emulex OneConnect OCm11102-N-X Manuel du propriétaire

Manuels Adaptateur populaires d'autres marques

PCB Piezotronics

PCB Piezotronics 090B274 Manuel utilisateur

Auvidea

Auvidea J20 Manuel du produit

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuel utilisateur

Akribis

Akribis ITF-21-BISS-MIT Manuel utilisateur

Tenda

Tenda W54U Manuel utilisateur

ROHO

ROHO AGILITY Manuel utilisateur

PROLiNK

PROLiNK WN2001 Manuel utilisateur

Hawking

Hawking HUF2 Manuel utilisateur

Airlink101

Airlink101 AWLC4030 Manuel utilisateur

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuel utilisateur

Philips

Philips SWA4554S/10 Manuel utilisateur

JVC

JVC TS-C9D2B Manuel d'instructions

NETGEAR

NETGEAR A6100 Manuel utilisateur

D-Link

D-Link DWA-121 Manuel utilisateur

Philips

Philips SWA2037 Manuel utilisateur

Basalte

Basalte 0610-20 Manuel utilisateur

Yealink

Yealink EHS40 Manuel utilisateur

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuel utilisateur