EMTAC A2588 Manuel utilisateur
0
INSTALLATION MENU
Wireless LAN
Access Point
2.4 GHz / 11 Mbps / DSSS
PN:A2588
1
FCC INFORMATION
The Federal Communication Commission Radio Frequency
Interference Statement includes the following paragraph:
This equipment has been tested and found to comply with the
limits for a Class B digital Device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction,
may cause harmful interference to radio communication. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of followingmeasures:
nReorient or relocate the receiving antenna.
nIncrease the separation between the equipment and receiver.
nConnect the equipment into and outlet on a circuit different
from that to which the receiver is connected.
nConsult the dealer or an experienced radio/TV technician for
help.
2
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause
undesired operation.
Radiation Exposure:
This equipment complies with FCC RF radiation exposure limits
set forth for an uncontrolled environment. This equipment should
be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
The user should not modify or change this equipment.
Modification could void authority to use this equipment.
3
Notice
The information in this document is subject to change in order to
improve reliability, design, or function without prior notice and
does not represent a commitment.
No part of this document may be reproduced or transmitted in any
form or by any means.
Trademark Acknowledgments
PRISM 2 is registered trademark of Intersil, Inc.
Microsoft Windows are registered trademarks of Microsoft Corp.
IBM and Thinkpad are a registered trademark s of International
Business Machines Corp.
All other product names or trademarks are property of their
respective owners. Product and cooperate names mention in this
publication are used for identification purpose only.
4
Package Contents
The package should contain following items:
1. The EMTAC A2588 11Mbps WLAN Access Point.
2. Driver disc.
3. This menu.
4. USB cord
5. Power Adapter
External Interface
1. USB Cord
2. EthernetCord
5
Software Installation Guide
You should have an Access Point driver disk from our agent, it
includes 2 major programs, one is “DFU” using USB port, and the
other is “AP Configuration” using Ethernet port.
For DFU
1. Run the “Setup.exe” in the folder of DFU of the driver disk.
Follow the guideline on the screen, and select the directory
where the application will be installed, it will deploy all files
that needed at that. At the end, windows will show a message
that installation is completed.
2. Power on the Access point.
3. After Access Point had powered on, then plug USB cord into
both port of host PC and AP.
4. You can run the program of “DFU”, which you can find in
“start” à”program” à”Atmel Utilities” à”DFU”. When the
DFU is working correctly, it will tell you what both version of
the Access Point firmware and this utility.
6
For AP Configuration
1. Run the “Setup.exe” in the folder of AP Configuration of the
driver disk. Follow the guideline on the screen, and select
the directory where the application will be installed, it will
deploy all files that needed at that. At the end, windows will
show a message that installation is completed.
2. Power on the Access point.
3. Plug the “cross over” type Ethernet cord into both port of
host PC and AP. (If you don’t have “cross over” type
Ethernet cord and have a hub, then you can use normal type
Ethernet cable to connect both host PC and AP to hub.)
4. You can run the program of “AP Configuration”, which you
can find in “start” à”program” à”Atmel Utilities” à”AP
Configuration”
5. Make sure that the IP address of your host PC and AP are in
the same sub-net, because this program is based on SNMP.
The default setting of IP address of AP is192.168.0.251
7
Utilities Using Guide
Basic Configuration
We highly recommend you that using “DFU” utility for the first
time setting of AP, and “AP Configuration” for latter regular
setting, (of course, you should already have a connect with AP
through the Ethernet cable). Because the DFU utility configures
the AP through USB port, it won’t care about any setting inside
the AP. So you can change any setting you need and make sure
what all the setting of AP are. After that, you may deploy the
AP in a not-easily-reachable working place, it is very
inconvenient to connect host PC and AP by USB cord, but it
should have an Ethernet cable to connected to.
For DFU
When you run the DFU, you will see a page like below.
8
Press “Configuration” to get the configuration of AP.
Note: Don’t download any file to AP, it will cause AP
crashed, except that your vendor give you the correct
firmware file(, like *.rom) and told you to download it.
Now, you can see all the setting of AP.
9
1. First, set the field of “Eth_IP_Address”, that is the IP
address of this AP. You should make sure that the IP address
is a valid address in your sub-net.
2. Set the field of “Eth_SubMask”, that is the sub-net mask of
this sub-net. It should be the same with your sub-net.
3. Set the field of “Wirel_ESSID”, that is the Extended Service
Set ID (ESSID) of this AP. All wireless stations want to
connect with this AP must have the same ESSID.
4. Set the field of “Wirel_Channel”, that is the channel that this
service set using. If more than one service set on the same
channel, they will equal-share the same access. And we
recommend you that it’s better to depart from more than one
channel for adjacent using channels, e.g. using channel 6 and
channel 8 concurrently will be better for channel 6 and
channel 7.
After the above setting, the AP should work properly.
Table des matières
Manuels Point d'accès sans fil populaires d'autres marques
D-Link
D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur
Ubiquiti
Ubiquiti NanoStation NSM2 Manuel utilisateur
Cisco
Cisco Aironet 1550 Series Manuel utilisateur
Aruba
Aruba IAP-335 Manuel utilisateur
Advantek Networks
Advantek Networks AWN-AP-54MR Manuel utilisateur
IP-COM
IP-COM AP355 Manuel utilisateur
