EMS FireCell FCZ-170-111 Mode d'emploi

Wireless RIM

Programming Guide

Contents

Introduction 3

Tools 3

Wireless RIM familiarisation 4

Adding a Wireless RIM to a Fusion Loop Module 5

Adding a Wireless RIM to a FireCell Radio Hub (manually) 6

Adding a Wireless RIM to a FireCell Radio Hub (via software) 8

Adding a Wireless RIM to the Control Panel 10

Linking a zone to a RIM 12

Linking an individual device to a RIM 16

Testing RIM functionality 20

Introduction

The FireCell Wireless Remote Indicator Module (RIM) is compatible with both the EMS FireCell

system and the EMS Fusion Loop Module.

It is possible to add (log on) the RIM to the FireCell system both manually and via FireCell

Conguration Tool software, whilst the RIM must be added to the Fusion Loop Module manually.

All of the aforementioned methods are detailed in this programming guide.

Also covered within this guide is the adding (logging on) of RIMs to the FireCell control panel, via

the Loop Explorer computer software plus two methods of programming the cause and eect

rules to link either, a zone of devices, or a single device to a RIM.

This guide has been written for engineers that have completed FireCell product training and

therefore have knowledge of the product and the basic programming functionality of the control

panel.

It is therefore assumed that the engineer is practised in the methodology of removing, editing

and sending Loop Explorer setup les to the FireCell control panel.

Note: screenshots shown in this programming guide depict FireCell Conguration Tool

version 60082 and Loop Explorer Version 3.0. Future software releases may vary both

visually and in operation.

Tools

Before starting the programming, the following items MUST be available.

Laptop c/w Loop Explorer software

FireCell control panel programming lead (FC-000-KEN)

Wireless RIM familiarisation

www.emsgroup.co.uk

Wireless Detector Base

PRESS HERE TO

LOG ON

Part No: FCZ-170-111

Wireless Module

Log on button

Power jumper

Ident number

device

unpowered

(pins unlinked)

device

powered

(both pins linked) RevX DD/MM/YY

1d872

Battery compartment Remote Indicator

Fire LED

Conrmation

LED

PRESS HERE TO

LOG ON

Adding a Wireless RIM to a Fusion Loop Module

Take the device to the Loop Module and follow the steps below:

With the loop module in its normal state, the screen will display: DEV01 AL00 FT00

Press the rotary control and the screen will display: Device Status

Turn the rotary control until the screen displays: Add New Device

Press the rotary control and the screen will display: Press Dev Log On

Press the device’s log on button for 2 seconds (the device’s

conrmation LED will illuminate). The screen will display: Add Dev xxxxx N?

If the ident shown does not match the ident of the new device to be added, press the rotary

control (with the above Add Dev xxxxx N? display shown). This will return the display to the

previous menu.

Adding

Press the rotary control and the screen will display:

Add Dev xxxxx Y?

If the device ident is correct, turn the rotary control until the

screen displays:

Address 007

Turn the rotary control, until the desired device address is shown:

Address 002

Followed by:

DEV02 AL00 FT00

Press the BACK button, to return to the front display:

I/O Added

Press the rotary control to conrm the device address. The screen

will display:

Adding a Wireless RIM to a FireCell Radio Hub (manually)

Take the device to the Radio Hub and follow the steps below:

With the radio hub in its normal state the screen will display: DEV15 AL00 FT00

Press the rotary control and the screen will display: Device Status

Turn the rotary control until the screen displays: Add New Device

Press the rotary control and the screen will display: RCC01=06 Max 31

Turn the rotary control, until the screen displays the required

RCC to programmed the device to: RCC02=03 Max 31

Press the rotary control and the screen will display:

Add By Log On

Turn the rotary control until the screen displays the required

addressis shown and press the rotary control to select. The

Loop 1 Addr 016

Press Dev Log On

Press the rotary control and the screen will display:

If the ident shown does not match the ident of the new device to be added, press the rotary

control (with the above Add Dev xxxxx N? display shown). This will return the display to the

previous menu.

Add Dev xxxxx N?

Press the device log on button for 2 seconds. The device’s

conrmation LED will illuminate and the she screen will display:

New Addr L2 A007

Press the rotary control and the screen will now conrm the new

devices loop and address number:

Add Dev xxxxx Y?

Conrm the ident number displayed is the same as located on the

device. If correct, turn the rotary control until the screen displays:

Press the BACK button until the screen displays: Unassigned Dev

Press the rotary control and the screen will display: Device Status

Turn the rotary control until the screen displays the required

Loop to be programmed and press the rotary control to select. Loop 2 Addr 007

Press the rotary control and the screen will display: Assign ALL

Press the rotary control and the screen will display: Dev 000 of 001

Followed by: Done 001 of 001

Note: If unsuccessful when operation is carried out next to the Radio Hub, re-try steps 16-19

with the device installed in its correct installed location.

Once complete, press the BACK button until the screen displays: DEV16 AL00 FT00

Turn the rotary control until the screen displays: Assign Device

Adding a Wireless RIM to a FireCell Radio Hub (via software)

When programming the Wireless RIM to a FireCell system via the conguration tool software, the

device should be added as an Input/Output unit.

All of the standard programming features for the device remain the same.

Details are explained below:

Add the Wireless RIM, by clicking on the ‘I/O Unit’ icon from the ‘Device Palette’.

The new device will be shown in the main window, allocated to the RCC as shown.

Complete the device’s ‘Ident’, ‘Loop’ and ‘Address’elds shown below.

An example of an RCC programmed with three Wireless RIMs is shown below:

Adding a Wireless RIM to the Control Panel

The Wireless RIMs are added to the Loop Explorer conguration le as ‘Input/Output Wireless’

devices.

The selection of available wireless devices is shown below with the‘Input/Output Wireless’device

selected for the RIM highlighted.

Double click on the ‘Input/Output Wireless’ icon, shown above, to add the RIM to the setup. An

example is shown below:

Double click on the ‘Input/Output Unit Wireless’ icon shown above to expand the device to show

the input and output, as shown below:

Autres manuels pour FireCell FCZ-170-111

Ce manuel convient aux modèles suivants

Table des matières

Manuels Écran tactile populaires d'autres marques

FlowLine

FlowLine Data loop Manuel utilisateur

ALPEX

ALPEX AEx-8 P Series Manuel utilisateur

Ltech

Ltech E5S Manuel utilisateur

Harman

Harman AMX MODERO S MSD-701-L2 Manuel utilisateur

Acnodes

Acnodes PC 1150 Manuel utilisateur

AIS

AIS IP10IA99 series Manuel utilisateur

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manuel utilisateur

YASKAWA

YASKAWA TP 610C Manuel utilisateur

B&R

B&R Power Panel C Series Manuel utilisateur

Beijer Electronics

Beijer Electronics X2 control Manuel utilisateur

AXIOMTEK

AXIOMTEK GOT321W-521 Manuel utilisateur

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manuel utilisateur

Qomo

Qomo QIT1386 Manuel utilisateur

DFI

DFI KS104-CD Manuel utilisateur

AMX

AMX AXP-PPC Mode d’emploi

Sartorius

Sartorius X3 PR 5410 Manuel utilisateur

AMX

AMX Modero X Series Manuel utilisateur

Advantech

Advantech TPC-30 Series Manuel utilisateur