Emmes EVA Manuel utilisateur
1. EVA Display Base
2. EVA Display
3. EVA iPod Box
a. EVA iPod charging cable
b. EVA iPod
c. EVA Program Flash Drive
4. EVA PC
5. Power Cable for
EVA Display
6. Power Cable for EVA PC
7. Orange HDMI Cable
8. Light Meter
9. Measuring Tape
10. Ruler
QUICK START GUIDE
Before you begin, check to make sure you
have the following parts:
1
3
4
5
6
78
9
10
1 UNPACK
• Lay parts from top tray on a clean at surface.
• Lay EVA display screen down on a clean at surface.
• Open EVA iPod box and remove all USB &
cable accessories.
2 ASSEMBLE
Connect display base to display head:
• Pull up EVA display arm.
• Matching up arrows, slide EVA display base onto display arm.
• Turn thumb nut to secure EVA display arm to EVA display
base, then fold thumb lever at.
Aach EVA PC to back of display:
• Stand EVA display on its base and turn it so the
screen is facing away from you.
• The two screw/pegs on the EVA PC slide into the
slots on the metal plate on the EVA display.
• Slide EVA PC down to lock it to metal plate.
3 CONNECT
• Insert the EVA display power cable into appropriate
receptacle on the EVA display.
• Insert one end of the EVA display (HDMI) cable into
appropriate receptacle on the EVA display.
• Insert the EVA PC power cable into the appropriate
receptacle on the EVA PC.
• Insert the remaining end of the EVA display (HDMI)
cable into appropriate receptacle on the EVA PC.
• Insert EVA iPod charging cable into YELLOW USB
PORT (fast charge). Always reserve this port for
charging the EVA iPod.
3
a
b
c
2
4
2
• Insert EVA iPod charging cable into EVA iPod.
• Insert Emmes EVA Program Flash Drive into USB
port next to the one reserved for the EVA iPod.
4 ORIENT
• Turn enre connected assembly around so the
screen is facing you.
• Organize all cables as necessary, being mindful of
where available power outlets are located.
• Plug wall-side ends of power cables into available
receptacles.
5 TURN ON
• Power on EVA iPod – single press and briey hold
the power buon.
• Power on the EVA display – single press once the
right-most buon on the EVA display unl it lights
up any color (orange or blue).
• Power on the EVA PC – single press the power
buon.
6 WAIT
**NOTE** This step is important every me the
device is restarted or powered on.
• Once ALL components are on and fully booted
(iPod shows lock-screen [1]; display shows “Tesng
Requirements”[2]), WAIT at least 30 seconds
BEFORE launching the EVA App on the EVA iPod.
a
7
c
5
b
6
[1] [2]
contact EVA support.
Proles. If you don’t see the study you’re looking for,
> ManageStudies and scroll through available Study
Enable Study Proles:
In the EVA App, tap Sengs
as necessary to look up the previous test.
EVA App, tap “Test Results”, select NON STUDY, proceed
Look up the previous NON STUDY test result:
In the
the results screen.
with the prompts. Complete/nish the test and note
select NON STUDY, proceed and familiarize yourself
Try an E-ETDRS Test:
In the EVA App, tap E-ETDRS,
•
Shutdown.
•
Sleep/Wake Up
•
Sengs
•
Test Results
•
Chart
•
Low Contrast ATS-HDTV
•
Low Contrast E-EDTRS
•
ATS-HOTV
•
E-EDTRS
sub-applicaons:
Once the EVA App loads, you should see the following
WAIT for EVA App to load:
it may take severalmoments.
the arrow.
Single-tap the EVA App on the EVA iPod screen below
7 LAUNCH EVA APP
Autres manuels Emmes Équipement de test
Manuels Équipement de test populaires d'autres marques
SMART
SMART KANAAD SBT XTREME 3G Series Manuel utilisateur
Agilent Technologies
Agilent Technologies BERT Serial Manuel utilisateur
Agilent Technologies
Agilent Technologies N3280A Manuel utilisateur
Vernier
Vernier Go Direct Voltage Manuel utilisateur
Lifeloc
Lifeloc R.A.D.A.R. Manuel utilisateur
Fluke
Fluke T5-600 Instructions d'utilisation et d'installation
