Emerson CF760AB00 Manuel utilisateur

WARNING: To avoid fire, shock, and serious personal injury, follow these instructions.

Safety Instructions

1. Read your owner’s manual carefully and keep it for future reference.

2. Before servicing or cleaning unit, switch power off at service panel and lock service panel

disconnecting means to prevent power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the

service panel.

3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off

the power to the ceiling fan before servicing.

4. Do not put anything into the fan blades while they are turning.

5. Do not operate reversing switch until fan blades have come to a complete stop.

Additional Safety Instructions for Installation

1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not

operate fan without blades.

2. The installation is to be in accordance with the National Electrical Code, ANSI/NFPA 70-1999 and

Local Codes. Use the National Electrical Code if Local Codes do not exist. The ceiling fan must be

grounded as a precaution against possible electrical shock. Electrical installation should be made

or approved by a licensed electrician.

3. The outlet box and joist must be securely mounted and capable of reliably supporting at least 50

pounds. Use only U.L. outlet boxes listed as “Acceptable for Fan Support”, and use the mounting

screws provided with the outlet box. Most outlet boxes commonly used for support of light fixtures are

not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.

4. The downrod furnished with the fan provides the minimum recommended floor to fan blade

clearance for an 8 foot ceiling.

5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental

contact with the fan blades.

6. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not

know enough about electrical wiring, have your fan installed by a licensed electrician.

WARNING: To avoid fire, shock or injury, do not use an Emerson or any other brand of control not

specifically approved for this fan.

WARNING: This product is designed to use only those parts supplied with this product and/or any

accessories designated specifically for use with this product by Emerson Electric Co. Substitution of

parts or accessories not designated for use with this product by Emerson Electric Co. could result in

personal injury or property damage.

WARNING: To Reduce the risk of personal injury, do not bend the blade flange when installing the

blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between

rotating fan blades.

Part No. F40BP72870000 Form No. BP7287

READ AND SAVE THESE INSTRUCTIONS

60” DESIGNER

Net Weight: 30.0 Lbs.

Ceiling Fan

Owner's Manual

CF760AB00

CF760AW00

CF760WW00

CF760BS00

CF760ORB00

Model No. CF760PW00

CF760WB00

WARNING

BP7287 60" DESIGNER FAN 3/10/05 10:42 AM Page 1

This Manual Is Designed to Make it as Easy as Possible for You to

Assemble, Install, Operate and Maintain Your Ceiling Fan

Tools Needed for Assembly

One Phillips head screwdriver

One stepladder

One 1/4” blade screwdriver

One wire stripper

Three wire connectors (supplied).

MATERIALS

Wiring outlet box and box connectors must

be of type required by the local code. The

minimum wire would be a 3-conductor (2-

wire with ground) of the following size:

Before assembly your ceiling fan, refer to

section on proper method of wiring your

fan (page 7). If you feel you do not have

enough wiring knowledge or experience,

have your fan installed by a licensed

electrician.

WARNING

Do not install or use fan if any part is

damaged or missing. Call Toll-Free:

1-800-654-3545

WARNING

This product is designed to use only

those parts supplied with this product

and/or any accessories designated

specifically for use with this product by

Emerson Electric Co. Substitution of

parts or accessories not designated for

use with this product by Emerson

Electric Co. could result in personal

injury or property damage.

WARNING

Installed Wire Length Wire Size A.W.G.

Up to 50 ft. 14

50-100 ft. 12

Unpacking Instructions

For your convenience, check-off boxes are provided next to each step. As each

step is completed, place a check mark in the box. This will insure that all steps

have been completed and will be helpful in finding your place should you be

interrupted.

1. Check to see that you have received

the following parts:

NOTE: If you are uncertain of part

description, refer to exploded view

illustration.

a. Fan motor assembly

b. One switch housing assembly

c. Five fan blades

d. One ceiling cover

e. Five blade flanges

f. One hanger ball/downrod assembly

g. One hanger bracket

h. One coupling cover

i. One loose parts bag containing:

1. Sixteen 3/16-24 x 1/2”

slotted Phillips blade screws

2. Sixteen blade washers

3. Eleven 1/4-20 x 1/2” Phillips oval

head flange screws

4. One wood pendant

5. One coupling

6. Three wire connectors

7. Two threaded studs

8. Two knurled knobs

9. Two lockwashers

10. One clevis pin

11. One hairpin clip

COUPLING

COVER

CEILING

COVER

BLADE

FLANGES

SWITCH CUP

ASSEMBLY

HANGER

BRACKET

HANGER BALL/

DOWNROD

ASSEMBLY

LOOSE

PARTS

BAG

FAN MOTOR

ASSEMBLY

FAN

BLADES

BP7287 60" DESIGNER FAN 3/10/05 10:42 AM Page 2

It is critical that the clevis pin in the

motor coupling is properly installed and

the setscrews securely tightened. Failure

to verify that the pin and setscrews are

properly installed could result in the fan

falling.

WARNING

NOTE: Place the parts from the loose

parts bags in a small container to keep

them from being lost. If any parts are

missing, contact your local retailer or

catalog outlet for replacement before

proceeding.

2. Remove the fan assembly from the

protective plastic bag. Place the fan

assembly into the upper foam pad with

the bottom of the motor facing up.

The upper foam pad serves as a holder

for the fan during the first stages of

assembly.

How to Put Your Ceiling Fan Together

1. Remove the hanger ball by loosening

the setscrew in the hanger ball until the

ball falls freely down the downrod

(Figure 1). Remove the pin from the

downrod, then remove the hanger ball.

Retain the pin and hanger ball for

reinstallation in step 5.

2. Separate, untwist and unkink the three

80” motor leads. Route the motor lead

wires through the downrod. Remove

the upper setscrew from the motor

coupling. Align the clevis pin holes in

the downrod with the holes in the motor

coupling. Install the clevis pin and

secure with the hairpin clip (Figure 2).

The clevis pin must go through the

holes in the motor coupling and the

holes in the downrod. Be sure to push

the straight leg of the hairpin clip

through the hole near the end of the

clevis pin until the curved portion of the

hairpin clip snaps around the clevis pin.

The hairpin clip must be properly

installed to prevent the clevis pin from

working loose. Pull on the downrod to

make sure the clevis pin is properly

installed. Reinstall the upper setscrew

in the motor coupling. Check that the

lower setscrew is tightened securely

(Figure 2).

NOTE: The setscrews must be properly

installed as described above, or fan

wobble could result.

3. Make sure the grommet is properly

installed in the coupling cover, then

slide the coupling cover on the

downrod until it rests on the motor

housing. Place the ceiling cover over

the downrod. Be sure that the ceiling

cover and the coupling cover are both

oriented correctly (Figure 3).

DOWNROD

SETSCREW

HANGER

BALL

Figure 1

CLEVIS PIN

UPPER

SETSCREW

CLEVIS

MOTOR

COUPLING

SETSCREW

CLEVIS

DOWNROD

HAIRPIN CLIP

SETSCREW

MOTOR COUPLING

HAIRPIN

CLIP

Figure 2

CEILING

COVER

COUPLING

COVER

Figure 3

BP7287 60" DESIGNER FAN 3/10/05 10:42 AM Page 3

4. Reinstall the hanger ball (Figure 4) on

the downrod as follows. Route the

three 80” motor leads through the

hanger ball. Position the pin through

the two holes in the downrod and align

the hanger ball so the pin is captured in

the groove in the top of the hanger ball.

Pull the hanger ball up tight against the

pin and securely tighten the setscrew in

the hanger ball. A loose setscrew could

create fan wobble.

5.The fan comes with blue, black and

white leads that are 80” long. Before

installing fan, measure up

approximately 6 to 9-inches above top

of hanger ball/downrod assembly. Cut

off excess leads and strip back

insulation 1/2-inch from end of leads.

6. Engage the connector of the switch

housing assembly with the motor

connector (Figure 5). The two

connectors are keyed and color-coded

and must be mated correctly (color-to-

color) before they can be engaged.

Make sure the connector latch closes

properly.

7. Remove the three switch housing

mounting screws (Figure 5) from the

switch housing plate. Position the

switch housing assembly on the switch

housing plate and align the holes in the

switch housing assembly with the holes

in the plate. Secure the switch housing

assembly by installing the three screws

(Figure 6).

It is critical that the pin in the hanger ball

is properly installed and the setscrew

securely tightened. Failure to verify that

the pin and setscrew are properly

installed could result in the fan falling.

WARNING

To avoid possible fire or shock, do not

pinch wires between the switch cup

assembly and the switch cup plate.

WARNING

DOWNROD

HANGER BALL

CEILING

COVER

SETSCREW

Figure 4 8. Turn fan assembly upside down in

preparation for mounting fan blade

assemblies.

9. Mount blade flanges to fan blades

using three 3/16-24 x 1/2” slotted

Phillips blade screws and three blade

washers (Figure 7).

NOTE: Take care not to scratch fan

housing when installing blades.

NOTE: Remove and discard the four

shipping spacers and screws from the

motor hub.

MOTOR CONNECTOR

SWITCH HOUSING

CONNECTOR

SWITCH HOUSING

MOUNTING SCREW (3)

Figure 5

SWITCH

HOUSING

ASSEMBLY

MOUNTING

SCREWS (3)

Figure 6

FAN BLADE

BLADE WASHER (3)

3/16-24 x 1/2" SLOTTED

PHILLIPS BLADE SCREW (3)

BLADE FLANGE

Figure 7

BP7287 60" DESIGNER FAN 3/10/05 10:42 AM Page 4

To reduce the risk of personal injury, do

not bend the blade flange when installing

the blade flanges, balancing the blades

or cleaning the fan. Do not insert foreign

objects in between rotating fan blades.

WARNING

10. Loosely attach one blade assembly to

the motor hub using two 1/4-20 x 1/2”

Phillips oval head flange screws.

Make sure the screws are NOT

tightened. (Figure 8.) Repeat this

procedure for other four blade

assemblies.

11. The blade flanges have an

interlocking feature that must be fully

engaged before tightening the screw.

Make sure all the flanges are properly

engaged and then tighten the flange

screws. If one of the flanges does not

seat properly on the motor hub,

loosen the adjacent flange screws, re-

engage and reseat the flanges, then

tighten the screws again.

12. You have now completed the

assembly of your new ceiling fan. You

can now proceed with hanging and

wiring your fan.

BLADE

ASSEMBL

BLADE FLANGE

SCREWS

Figure 8

Electrical Requirements

Your new ceiling fan will require a

grounded electrical supply line of 120 volts

AC, 60 Hz, 15 amp circuit.

The outlet box must be securely anchored

and capable of withstanding a load of at

least 50 pounds.

To reduce the risk of fire, electrical

shock, or personal injury, mount fan to

outlet box marked “Acceptable for Fan

Support”, and use screws supplied with

outlet box. Most outlet boxes commonly

used for support of light fixtures are not

acceptable for fan support and may need

to be replaced. Consult a qualified

electrician if in doubt.

WARNING

To avoid fire or shock, follow all wiring

instructions carefully.Any electrical work

not described in these instructions

should be done or approved by a

licensed electrician.

WARNING

Turning off wall switch is not sufficient.

To avoid possible electrical shock, be

sure electricity is turned off at the main

fuse box before wiring. All wiring must be

in accordance with National and Local

codes and the ceiling fan must be

properly grounded as a precaution

against possible electrical shock.

WARNING

If your fan is to replace an existing ceiling

light fixture, turn electricity off at the main

fuse box at this time and remove the

existing light fixture.

BP7287 60" DESIGNER FAN 3/10/05 10:42 AM Page 5

How to Hang Your Ceiling Fan

The fan must be hung with at least 7' of

clearance from floor to blades (Figure 9).

WARNING

The outlet box and joist must be securely

mounted and capable of supporting at

least 50 lbs. Use only a U.L. outlet box

listed as “Acceptable for Fan Support”.

WARNING

To reduce the risk of fire, electrical

shock, or personal injury, mount fan to

outlet box marked “Acceptable for Fan

Support”, and use screws supplied with

outlet box. Most outlet boxes commonly

used for support of light fixtures are not

acceptable for fan support and may need

to be replaced. Consult a qualified

electrician if in doubt.

WARNING

AT LEAST

CEILING

FLOOR

Figure 9

1.Securely attach the hanger bracket to

the outlet box using the two screws

supplied with the outlet box. (Figure 10.)

2. Carefully lift the fan and seat the

hanger ball/downrod assembly on the

hanger bracket that was just attached

to the outlet box (Figure 11). Be sure

the groove in the ball is lined up with

tab on the hanger bracket (Figure 10).

TWO SCREWS

SUPPLIED WITH

OUTLET BOX HANGER

BRACKET

TAB

OUTLET

BOX

Figure 10

Failure to seat tab in groove could cause

damage to electrical wires and possible

shock or fire hazard.

WARNING

To avoid possible fire or shock, do not

pinch wires between the hanger

ball/downrod assembly and hanger

bracket.

WARNING

OUTLET

BOX

HANGER

BRACKET

HANGER BALL/

DOWNROD ASSEMBLY

NOTE: CEILING COVER, SUPPLY WIRES AND FAN

WIRES OMITTED FOR CLARITY.

Figure 11

BP7287 60" DESIGNER FAN 3/10/05 10:42 AM Page 6

5. Secure the ceiling cover in place by

sliding lockwashers over the threaded

studs and installing the two knurled

knobs (supplied). (Figure 13). Tighten

the knurled knobs securely until the

ceiling cover fits snugly against the

ceiling and the hole in the ceiling cover

is clear of the downrod. Your fan is now

wired to be turned on and off from the

fan switch.

6. Cut the 3-speed switch pull chain to a

desired length (optional). Connect the

wood pendant (supplied) to the 3-

speed switch pull chain by sliding the

wooden pendant (small hole first) onto

the pull chain.Attach the chain coupling

to the end of the chain and allow the

wooden pendant to fall down over the

coupling.

How to Wire Your Ceiling Fan

If you feel that you do not have enough

electrical wiring knowledge or

experience, have your fan installed by a

licensed electrician.

To avoid possible electrical shock, be

sure electricity is turned off at the main

fuse box before wiring.

NOTE: If you are not sure if the outlet box

is grounded, contact a licensed

electrician for advice, as it must be

grounded for safe operation.

WARNING

1. Connect the green grounding lead from

the hanger ball and the green

grounding lead from the hanger bracket

to the grounding conductor of supply

(this may be a bare wire or wire with

green colored insulation). Securely

connect wires with wire connectors

supplied.

GROUND

WIRE

LISTED

WIRE

CONNECTOR

(3)

GREEN WIRE

(GROUND)

FROM

HANGER

BRACKET

GREEN WIRE

(GROUND) FROM

HANGER BALL

WHITE

SUPPLY

(NEUTRAL)

WHITE FAN

WIRE

BLACK

SUPPLY

(HOT)

BLACK AND BLUE

FAN WIRES

Figure 12 NOTE: CEILING COVER

OMITTED FOR CLARITY.

NOTE: If you are using an Emerson

Light Fixture with your fan, see Light

Fixture Owner’s Manual for wiring.

2. Securely connect the fan motor white

wire to the supply white (neutral) wire

using wire connector supplied (Figure

12). Securely connect the fan motor

black wire and blue wire to the supply

black (hot) wire using wire connector

supplied (Figure 12). After connections

have been made, turn leads upward

and carefully push leads into the outlet

box, with the white and green leads on

one side of the outlet box and the black

and blue leads on the other side of the

outlet box.

Check to see that all connections are

tight, including ground, and that no bare

wire is visible at the wire connectors,

except for the ground wire. Do not

operate fan until blades are in place.

Noise and fan damage could result.

WARNING

To avoid possible fire or shock, make

sure that the electrical wires are

completely inside the outlet box and not

pinched between the ceiling cover and

the ceiling.

WARNING

3. Screw the two threaded studs

(supplied) into the tapped holes in the

hanger bracket.

4. Lift the ceiling cover up to the threaded

studs and turn until studs protrude

through the holes in the ceiling cover

(Figure 13).

THREADED

STUD (2)

LOCKWASHER

CEILING

COVER

KNURLED KNOBS (2)

Figure 13

BP7287 60" DESIGNER FAN 3/10/05 10:42 AM Page 7

Periodic cleaning of your new ceiling fan is

the only maintenance that is needed.

When cleaning, use only a soft brush or

lint free cloth to avoid scratching the finish.

Abrasive cleaning agents are not required

and should be avoided to prevent damage

to finish.

Using Your Ceiling Fan

Maintenance

1. Restore electrical power to the outlet

box by turning the electricity on at the

main fuse box.

2. Check the operation of the fan by

gently pulling on the pull chain switch.

3. All fans are shipped from the factory

with the reversing switch positioned to

circulate air downward. If airflow is

desired in opposite direction, turn your

fan off and wait for the blades to stop

turning, then slide the reversing switch

to opposite position, and turn fan on

again. The fan blades will turn in the

opposite direction and reverse the

airflow.

Your fan model is equipped with a 4-

position, 3-speed pull chain switch. The

operating sequence is as follows:

THREE-SPEED

1st Pull—HIGH

2nd Pull—Medium

3rd Pull—Low

4th Pull—OFF

SPEED

CONTROL

SWITCH REVERSIBLE

SWITCH

Accessories

Do not use water when cleaning your

ceiling fan. It could damage the motor or

the blades and create the possibility of

an electrical shock.

WARNING

This product is designed to use only

those parts supplied with this product

and/or any accessories designated

specifically for use with this product by

Emerson Electric Co. Substitution of

parts or accessories not designated for

use with this product by Emerson

Electric Co. could result in personal

injury or property damage.

WARNING

The use of any other control not

specifically approved for this fan could

result in fire, shock and personal injury.

WARNING

IMPORTANT CARE INSTRUCTIONS

For Your Ceiling Fan

1. Ceiling Fan Light Kits (see store or

catalog).

2. Ceiling Fan/Light Controls (see store

or catalog).

3. Downrod Extension Kits (see store or

catalog).

DATE CODE:

The date code of this fan may be found on the box, stamped in ink on a white label.

You should record this data above and keep it in a safe place for future use.

BP7287 60" DESIGNER FAN 3/10/05 10:42 AM Page 8

Trouble Shooting

TROUBLE PROBABLE CAUSE SUGGESTED REMEDY

1.Fan will not 1.Fuse or circuit breaker 1. Check main and branch

start. blown. circuit fuses or circuit breakers.

2.Loose power line 2. Check line wire connections

connections to the fan, or to fan and switch wire

loose wire connections in connections in the switch

the switch housing. housing.

WARNING: Make sure

main power is turned off.

3.Reversing switch in neutral 3. Make sure reversing switch

position. position is all the way to one

. side.

2.Fan sounds 1.Blades not attached to fan. 1. Attach blades to fan before

noisy. operating.

2.Loose screws in motor 2. Check to make sure all screws

housing. in motor housing are snug

(not over-tight).

3.Screws securing fan blade 3. Check to make sure the screws

flanges to motor are loose. which attach the blade flanges

to the motor are tight.

4.Wire connectors inside switch 4. Check to make sure wire

housing rattling. connectors in switch housing

are not rattling against each

other or against the interior wall

of the switch housing.

WARNING: Make sure main

power is turned off.

5.Motor noise caused by solid- 5. Some fan motors are sensitive

state variable speed control. to signals from Solid-State

variable speed controls. If Solid-

State Control is used and motor

noise results, choose an

alternative control method.

6.Screws holding blades to 6. Tighten screws securely.

flanges are loose.

3.Fan wobbles 1.Setscrew in motor coupling is 1. Tighten both setscrews securely

excessively. loose. in the motor coupling.

2.Setscrew in the hanger ball/ 2. Tighten the setscrew in the

downrod assembly is loose. hanger ball/downrod assembly.

3.Screws securing fan blade 3. Check to be sure screws which

flanges to motor are loose. attach the fan blade flanges

to the motor are tight.

4.Fan blade flanges not seated 4. Check to be sure that the

properly. screws securing the fan

blade flanges seat firmly.

5.Hanger bracket and/or ceiling 5. Tighten the hanger bracket

outlet box is not securely screws to the outlet box, and/or

fastened. secure outlet box.

6.Fan blades out of balance. 6. Interchanging an adjacent (side

by-side) blade pair can

redistribute the weight and result

in smoother operation.

Or use supplied balancing kit to

balance blades.

WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX

OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN.

BP7287 60" DESIGNER FAN 3/10/05 10:42 AM Page 9

Repair Parts

Before discarding packaging material, be certain all parts have been removed.

HOW TO ORDER REPAIR PARTS

WHEN ORDERING REPAIR PARTS,ALWAYS GIVE THE FOLLOWING INFORMATION:

• PART NUMBER

• NAME OF ITEM

• PART DESCRIPTION

• MODEL NUMBER

The model number of your Fan will be found on a label attached to the top housing.

For repair parts, phone 1-800-654-3545.

BP7287 60" DESIGNER FAN 3/10/05 10:42 AM Page 10

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Emerson Ventilateur

Emerson

Emerson HIGHPOINT CF205GES01 Manuel utilisateur

Emerson

Emerson BUILDER CF700AB08 Manuel utilisateur

Emerson

Emerson EUCLID CF500AP00 Manuel utilisateur

Emerson

Emerson Northwind Contemporary Snugger CF805SAW01 Manuel utilisateur

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuel utilisateur

Emerson

Emerson CF550BS00 Manuel utilisateur

Emerson

Emerson MARIOL PORTICO CF690CK00 Manuel utilisateur

Emerson

Emerson CF244BS00 Manuel utilisateur

Emerson

Emerson CF205BS01 Manuel utilisateur

Emerson

Emerson Carrera Veranda CF552GBZ00 Manuel utilisateur

Emerson

Emerson CONTOURS KF140TZ00 Manuel utilisateur

Emerson

Emerson SUMMER NIGHT CF652ORB01 Manuel utilisateur

Emerson

Emerson NOTTINGHAM CF4600GLZ00 Manuel utilisateur

Emerson

Emerson CF330GRT00 Manuel utilisateur

Emerson

Emerson PRIMA CF901BS00 Manuel utilisateur

Emerson

Emerson NORTHWIND Manuel utilisateur

Emerson

Emerson WYATT CF530BS00 Manuel utilisateur

Emerson

Emerson CARRERA GRANDE ECO CF788AP01 Manuel utilisateur

Emerson

Emerson CORNERSTONE CF1AB01 Manuel utilisateur

Emerson

Emerson HF948W Manuel utilisateur

Emerson

Emerson PRIMA SNUGGER CF905BS00 Manuel utilisateur

Emerson

Emerson CF712AB02 Manuel utilisateur

Emerson

Emerson Botanica CF2500HTW01 Manuel utilisateur

Emerson

Emerson ASHLAND CF717BS00 Manuel utilisateur

Manuels Ventilateur populaires d'autres marques

ELTA FANS

ELTA FANS H03VV-F Manuel utilisateur

Hunter

Hunter 20714 Manuel d'instructions

Hunter

Hunter Caraway Manuel d'instructions

Panasonic

Panasonic FV-15NLFS1 Manuel utilisateur

Kompernass

Kompernass KH 1150 Manuel utilisateur

VES

VES FALA100/12V/TR Manuel utilisateur

Vertiv

Vertiv Liebert DCD Manuel utilisateur

Westinghouse

Westinghouse GFP Series Manuel utilisateur

Venmar

Venmar KUBIX HRV PLUS Series Manuel utilisateur

Maico

Maico ECR 31 Manuel utilisateur

Sonnenkonig

Sonnenkonig Dinky Manuel utilisateur

S&P

S&P ECOWATT HXBR Manuel utilisateur

Wider

Wider IMP03369BH Manuel utilisateur

Panasonic

Panasonic F-60DHN Manuel utilisateur

Hinkley

Hinkley HIGHLAND Manuel utilisateur

Broan

Broan 766BN Manuel utilisateur

Premium

Premium PFS16022 Instructions de montage

Litex Industries

Litex Industries E-CGL52CB5C1 Manuel utilisateur