Emerson 818-2050 Guide d'installation

EMERSON CONTROL LINK CPC® P/N 818-2050 REFRIG. CONTROLLER: OVERVIEW & OPERATION

CL-RSC Operation

EMERSON CONTROL LINK CPC® P/N 818-2050 REFRIG. CONTROLLER: GENERAL PARAMETERS

General Parameters

 General parameters are used by techni-

cians and operators to set the control set-

points and defrost schedules.

Before Changing General Parameters

 Before changing parameters, clear any

active alarms by pressing the Alarm Si-

lence button.

Changing General Parameters

 Do not lightly press buttons! You MUST

use considerable force while pressing

controller buttons or your commands

will not register!

 Press (SET) and hold for five seconds.

 If general mode programming has been

password protected, you will see PASS on

the display.

 Press (SET) and use the arrow keys to in-

crement the password number until the

correct password is shown and then press

(SET).

 Note: If general parameters an not pass-

word protected, PASS will not appear on

the display.

The display will show the first programmable

parameter: CSP (Case temperature Set Point).

The arrow keys may be used to scroll through

the list of general parameters. To change the

value of any parameter follow these steps:

1. Select the parameter using the arrow keys

(until the code is shown.

2. Press (SET).

3. Current value of this parameter will display.

Use arrow keys to change values.

4. Press (SET) to accept value.

5. Repeat steps 1-4 until all set points have

been properly configured.

6. When finished, press (SET) again for five

seconds to save changes and exit. The

display will blank for one second and then

revert to normal display if the save was

successful.

7. To cancel all changes, press and hold

(SILENCE) for five seconds, or leave con-

troller idle for 60 seconds. You will lose all

setpoint changes made since you entered

General Programming Mode.

See Warning at right.

SFT

Software Version - - -

WARNING!

You MUST press and hold

(SET) after changing setpoints

for changes to be permanent.

Leaving the controller idle for

60 seconds will log you

out and cancel all your

setpoint changes.

Note! See Technical Information Sheet In This Manual For This Case’s Settings

Note! See Technical Information Sheet In

This Manual For This Case’s Settings

EMERSON CONTROL LINK CPC® P/N818-2050 CONTROLLER: ADVANCED PARAMETERS & ALARMS

Advanced Parameters

 General parameters are used to change

higher-level parameters not directly related to

system operations.

 Selecting and changing advanced parame-

ters works the same way as general parame-

ters, except that they are accessed in a dif-

ferent way and require entering a different

password.

Before Changing Advanced Parameters

 Before changing parameters, clear any ac-

tive alarms by pressing the Alarm Silence

button.

Changing Advanced Parameters

 Do not lightly press buttons! You MUST

use considerable force while pressing

controller buttons or your commands will

not register!

 Press and hold the UP and DOWN buttons

simultaneously for five seconds to enter the

Advance Programming Mode. The display

will show

APAS

 Press (SET) and use the arrow keys to select

the correct password (default is 0000), and

press (SET) to enter it.

Installation Photos

 See next page for installation photos of Emerson Control Link CPC® P/N 818-2050 Refrigeration Controller.

 Note: Exact location may vary depending upon model and features.

EMERSON CONTROL LINK CPC® P/N 818-2050 REFRIG. CONTROLLER: INSTALLATION PHOTOS

Control Link

Refrigeration System Controller

Ballast

Enlarged View of Control Link

Refrigeration System Controller

Main Power

Switch

Note: This Sheet Applicable

To “CO” Cases Only

EMERSON CONTROL LINK CPC® P/N 818-2050 REFRIG. CONTROLLER: INSTALLATION PHOTOS

View of Control Link

Refrigeration System

Controller With Housing

Cover Removed

Control Link Refrigeration

System Controller With

Housing Cover Attached

EMERSON CONTROL LINK CPC® P/N 818-2050 REFRIG. CONTROLLER: INSTALLATION LOCATION

Main Power

Switch

Controller

Box

Controller

Field Wiring

Box

Table des matières

Autres manuels Emerson Contrôleurs

Emerson

Emerson Fisher 67C Manuel utilisateur

Emerson

Emerson FISHER T205B Manuel utilisateur

Emerson

Emerson EXD-HP1/2 Manuel utilisateur

Emerson

Emerson PMAC II Solo Manuel utilisateur

Emerson

Emerson E2 Manuel utilisateur

Emerson

Emerson Bettis RPE Series Manuel utilisateur

Emerson

Emerson Dixell XM670K Schéma de câblage

Emerson

Emerson Fisher Y600A Series Manuel utilisateur

Emerson

Emerson Fisher 1078 Manuel utilisateur

Emerson

Emerson Fisher easy-Drive 200L Manuel utilisateur

Emerson

Emerson Tescom 26-1000 Series Manuel utilisateur

Emerson

Emerson EC3-D72 Manuel utilisateur

Emerson

Emerson ControlWave MICRO Guide rapide

Emerson

Emerson TESCOM 44-6800 E Series Manuel utilisateur

Emerson

Emerson Dixell XR70T Schéma de câblage

Emerson

Emerson Fisher FIELDVUE DVC6200 SIS Manuel utilisateur

Emerson

Emerson Digistart IS1x0043B series Manuel utilisateur

Emerson

Emerson Aventics Sentronic PLUS 614 Manuel utilisateur

Emerson

Emerson Bettis SCE300 Manuel utilisateur

Emerson

Emerson Fisher 785C Manuel utilisateur

Emerson

Emerson E2 RX Series Manuel utilisateur

Emerson

Emerson Asco SentronicPLUS Manuel utilisateur

Emerson

Emerson El-O-Matic E Series Mode d’emploi

Emerson

Emerson Fisher 1098-EGR Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur

3M MicroTouch EX113 Manuel utilisateur