Emergency Caller Products EC-4 Mode d'emploi
1-800-227-1592 www.emergencycaller.com
EC4 Dialer Programming Guide
This guide is to help you program
your EC4 product.
(SEE QUICK REFERENCE GUIDE FOR CONDENSED VERSION)
Programming Emergency Numbers
1. Apply power to your EC4. Plug your AC-2P power supply
into wall outlet. Make sure the AC-2P is plugged into the top
of your EC4.
LCD Display Will Show
2. Press 1 to add the first phone number to call
LCD Display Will Show
1-800-227-1592 www.emergencycaller.com
3. Press 1 Again
LCD Display Will Show
4. Press “2 for No”. If you are going to send emergency
message to a pager number, press 1 for yes to add pager
number. See Pager number programming below if needed.
LCD Display Will Show
If you are entering more than one phone number, you must select
the location for each number Example: Select 1 for your first
1-800-227-1592 www.emergencycaller.com
Emergency number, Select 2 for your second number, Select 3 for
the third and so on. Dialer will take up to 8 telephone, cellphone
or pager emergency numbers
You now can enter up to 8 phone numbers. Enter each phone
number one by one.
Enter your first desired phone number. If the number is long
distance, enter area code (Number 1 first) then phone number.
If you are entering a cell phone number, please enter two (2) “P”
(Pauses) at the end of the last digit for each phone number. Do this
for every cell phone number. Press the "*" button to save after
entering each number.
Examples of how to enter phone numbers
Example for landline telephone with area code: 18581234567*
Example for cellular phone with area code: 18581234567PP*
1-800-227-1592 www.emergencycaller.com
If you entered the wrong number, the dialer cannot cycle
backwards, only forward.
If this happens just hit the * button and continue with Step 2 by
entering the location for number to correct (1-8). Wrong
numbers can be over written by going through the same process
again.
Once all of your emergency phone numbers have been entered,
Press 0 (DONE).
5. Once you have pressed 0 to end emergency number entry
display will show
If your telephone line requires dialing a single number or digit to
get an outside line or dial tone to call out, continue with 5a.
If not, Press 2 (NO) and proceed to 6.
5a. Press 1 (YES) to Program T-LINE.
1-800-227-1592 www.emergencycaller.com
LCD will display:
Press 1 (TONE)if you are using a standard telephone line with a dial
tone. (Dialer is Pre-set to TONE).
Press 2 (PULSE) if you are using a telephone line that uses pulse
relay to dial out. (Typically Not Used)
LCD will display
This step is where you will program the digit to dial out in order to
get an outside line or dial tone. (Dialer is Pre-set to OFF)
1-800-227-1592 www.emergencycaller.com
If your phone system requires dialing a digit to get an outside line
or dial tone, Press 1 (ON).
If your phone system does not require a digit to get an outside line
or dial tone, Press 2 (OFF).
If you pressed 1 (ON)
LCD will display
Enter the number to dial out (1 digit)
LCD will display
1-800-227-1592 www.emergencycaller.com
You can control how many times the dialer will call each emergency
numbers that you programmed into your EC4 Emergency Caller.
Enter desired number of attempts. (Dialer is Pre-set to 2 attempts).
LCD will display
You can control the number of Out Going Messages (OGM’s) that
will be delivered to each number. Enter desired number of
Messages repeated.
(Dialer is Pre-set to 2 Messages).
LCD will display
1-800-227-1592 www.emergencycaller.com
6. Press 1 (YES) to program Emergency Caller Out Going Message
(OGM)
LCD will display:
Press 2 (NO)
LCD will display
Press 1 (YES)
LCD will display
1-800-227-1592 www.emergencycaller.com
This is where you will record your emergency message that will
notify all phone numbers of your need for help.
Before recording, it is recommended to write down what your
OGM will say.
Hold the Dialer 6 inches away from you. Prepare yourself to speak
directly at the small MIC on the left side of the Dialer.
When you are ready to record, HOLD DOWN the “R” button while
you are recording your message at the same time. Release the "R"
button when you are finished recording.
Your OGM should be at least 10 seconds long and up to 52
seconds for a single channel system (13 seconds for each channel)
LCD will display
1-800-227-1592 www.emergencycaller.com
Press 1 (YES) to listen to your OGM that you recorded.
After the OGM has been played, the LCD will display:
Press 1 (YES) if you are satisfied with your OGM.
Press 2 (NO) if you wish to re-record your OGM and it will bring you
back to:
Follow the steps above from Step 6 until you are satisfied with
recording your OGM.
Once you are satisfied with your OGM Press 1 (YES) to Accept.
The LCD will display
Autres manuels pour EC-4
1
Autres manuels Emergency Caller Products Système de sécurité
Manuels Système de sécurité populaires d'autres marques
EDM
EDM Solution 6+6 Wireless-AE Manuel utilisateur
Highway Safety Group
Highway Safety Group EA401 Manuel utilisateur
Siren
Siren LED GSM Manuel utilisateur
Detection Systems
Detection Systems 7090i Instructions de montage
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuel utilisateur
Siemens
Siemens FDM273 Manuel utilisateur