Elumen8 ELUM107 Manuel utilisateur

Order codes:

ELUM107 - Black Housing

ELUM107A - White Housing

MP 120 LED Fresnel WW

User Manual

www.prolight.co.uk MP 120 LED Fresnel WW User Manual

Safety advice

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL

CAREFULLY BEFORE YOUR INITIAL START-UP!

• Before your initial start-up, please make sure that there is no damage caused during transportation.

• Should there be any damage, consult your dealer and do not use the equipment.

• To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

• Please note that damages caused by user modications to this equipment are not subject to warranty.

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused by the non-observance

of this manual or any unauthorised modication to the equipment.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual, the product may suffer damage and

the warranty becomes void. Incorrect operation may lead to danger e.g: short-circuit, burns and electric shocks etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and/or property.

CAUTION!

KEEP THIS EQUIPMENT

AWAY FROM RAIN,

MOISTURE AND LIQUIDS

CAUTION!

TAKE CARE USING

THIS EQUIPMENT!

HIGH VOLTAGE-RISK

OF ELECTRIC SHOCK!!

• Never let the power cable come into contact with other

cables. Handle the power cable and all mains voltage

connections with particular caution!

• Never remove warning or informative labels from the unit.

• Do not open the equipment and do not modify the unit.

• Do not connect this equipment to a dimmer pack.

• Do not switch the equipment on and off in short intervals,

as this will reduce the system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when

equipment is not in use or before cleaning! Only handle

the power-cable by the plug. Never pull out the plug by

pulling the power-cable.

• Make sure that the available mains supply voltage is

between 110~240V AC, 50/60Hz.

• Make sure that the power cable is never crimped or

damaged. Check the equipment and the power cable

periodically.

• If the equipment is dropped or damaged, disconnect the

mains power supply immediately and have a qualied

engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic

temperature uctuation (e.g. after transportation),

do not connect power or switch it on immediately.

The arising condensation might damage the equipment.

Leave the equipment switched off until it has reached

room temperature.

• If your product fails to function correctly, stop use

immediately. Pack the unit securely (preferably in the

original packing material), and return it to your Pro Light

dealer for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be

carried out by a qualied technician. THIS UNIT CONTAINS

NO USER SERVICEABLE PARTS.

• This lighting xture is for professional use only - it is

not designed for or suitable for household use. The

product must be installed by a qualied technician in

accordance with local territory regulations. The safety of

the installation is the responsibility of the installer. The

xture presents risks of severe injury or death due to re

hazards, electric shock and falls.

• Warning! Risk Group 2 LED product according to

EN 62471. Do not view the light output with optical

instruments or any device that may concentrate the beam.

• WARRANTY: Two years from date of purchase.

www.prolight.co.uk MP 120 LED Fresnel WW User Manual

Product overview & technical specications

The MP 120 Fresnel lighting xtures come equipped with a 20cm Fresnel lens and are powered with a 120W,

3000K COB LED. Producing a soft edged beam, the units not only have a manually adjustable beam angle

19°- 37°, they also come supplied with barn doors to further adjust the beam angle, making them ideal for stage

and theatrical lighting applications. These fresnels provide a superb light output and benet from temperature

controlled fan cooling for whisper quiet operation. The 4 push button display allows users to select DMX and

manual dimming modes along with dimming curves, whilst the powerCON and DMX inputs/outputs allow multiple

units to be daisy chained in an array, further enhancing their usage.

• 1 x 120W warm white

COB LED (3000K)

• Manually adjustable beam angle:

19°- 37°

• 14,800 Lux @ 2m (full on)

• 1.5kHz refresh rate

• DMX channels: 1/3 or 5 selectable

• 0-100% dimming and variable strobe

• 4 dimming curves in both LED and

halogen proles: Linear, square law,

inverse square law and S-curve

• 4 push button menu

with LCD display

• PowerCON input/output

• 5-Pin XLR input/output

• 3-Pin XLR input/output

• Temperature controlled fan

for whisper quiet operation

• Filter frame and

barn doors included

MP 120 LED Fresnel WW

0m 2m 3m 4m 5m

19° - Lux

37° - Lux

14800

3349

59200

13400

6580

1490

37°

3700

838

2370

536

19°

215mm

185mm

245mm

147mm

36mm

301mm

142mm

318mm

450mm

298mm

220mm

371mm

Specications MP 120 LED Fresnel WW

Power consumption 136W

Power supply 100~240V, 50/60Hz

Fuse T2A 250V

Dimensions 371 x 301 x 450mm (with bracket)

298 x 245 x 450mm (without bracket)

Weight 8.6kg

Order code ELUM107 - Black Housing

ELUM107A - White Housing

www.prolight.co.uk MP 120 LED Fresnel WW User Manual

POWER INPUT:

100-240V~50/60Hz

POWER OUTPUT:

100-240V~50/60Hz

DMX INPUTS DMX OUTPUTS

FUSE:

T2A 250V

09 10

03 0302 0412

05 06

Technical specications

01 - Earth point

02 - LCD display

03 - Function buttons

04 - Function knobs

05 - 3-Pin DMX input

06 - 3-Pin DMX output

07 - 5-Pin DMX input

08 - 5-Pin DMX output

09 - PowerCON input

10 - PowerCON output

In the box: 1 x xture,

1 x barn door

1 x PowerCON cable

& 1 x user manual

11 - Fuse T3A 250V

12 - Barn doors

13 - Hanging bracket

14 - Hanging bracket adjustable knob

www.prolight.co.uk MP 120 LED Fresnel WW User Manual

Operating instructions

DMX MODE DMX address setting

DMX MODE

ADDR:001

DMX MODE

ADDR:512

DMX FAIL

HOLD

DMX FAIL

BLACKOUT

Blackout if no DMX

signal present

Hold last command

DIMCURVE

Linear

DIMCURVE

I-Square

DIMCURVE

Square

Dimmer Curves

DIMCURVE

S-Curve

CHANNEL

1CH

CHANNEL

5CH

DMX channel setting

CHANNEL

3CH

SLAVE

MODE

DIMMODE

LED

DIMMODE

HALOGEN

LED/Halogen selection

MANUAL

STR:000

Panel.Ctrl

STR:255

MANUAL

DIM:000

MANUAL

DIM:255

Manual mode

TEMP

___ C/F

Soft Ver

V_.___

BACKLIG

OFF

BACKLIG

Backlight setting

FacReset

Yes

Factory reset

www.prolight.co.uk MP 120 LED Fresnel WW User Manual

DMX mode:

Operating in a DMX control mode environment gives the user the greatest exibility when it comes

to customising or creating a show. In this mode you will be able to control each individual trait of the

xture and each xture independently.

To access the DMX address mode, press the “MENU” button on the front of the unit to show

“DMX MODE” on the LCD display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons

to set the required DMX address. Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

To access the DMX channel mode, press the “MENU” button on the front of the unit to show

“CHANNEL” on the LCD display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons

to set the required DMX channel. Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

To choose what the xture does when it loses DMX signal, press the “MENU” button on the front of

the unit to show “DMX FAIL” on the LCD display. Now press the “ENTER” button and use the “UP” and

“DOWN” buttons to choose between “HOLD” or “BLACKOUT”.

Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

Operating instructions

Channel Value Function

1 000-255 Master dimmer (0-100%)

1 channel mode:

Channel Value Function

1 000-255 Master dimmer (0-100%)

2 000-255 Dimmer ne (0-100%)

3 000-005 LED on

006-255 Strobe (slow-fast)

4 000-005 No function

006-063 Linear dimmer curve (hold 3s)

064-127 Square dimmer curve (hold 3s)

128-191 I-Square dimmer curve (hold 3s)

192-255 S-Curve dimmer curve (hold 3s)

5 000-005 No function

006-063 LED dimmer mode (hold 3s)

064-127 Halogen dimmer mode (hold 3s)

128-255 No function

5 channel mode:

Channel Value Function

1 000-255 Master dimmer (0-100%)

2 000-255 Dimmer ne (0-100%)

3 000-005 LED on

006-255 Strobe (slow-fast)

3 channel mode:

Master/slave mode:

To set the master unit, put the xture into manual mode.

To set the other units in slave mode, press the “MENU” button and use the “UP” and “DOWN” buttons to

show “SLAVE MODE” on the LCD display. Press the “ENTER” button to conrm the setting. The unit will

now run in sequence with the master unit.

To exit out of any of the above options, press the “MENU” button.

Please ensure that all slave units are set to the same DMX channel mode as the master unit.

www.prolight.co.uk MP 120 LED Fresnel WW User Manual

Dimming curves

To access the units dimmer curves, press the “MENU” button to show “DIMCURVE” on the LCD display.

Press the “ENTER” button and use the “UP” and “DOWN” buttons to set the dimming curve required.

“Linear” - LELinear dimming curve

“S-Curve” - LED S-Curve dimming curve

“I-Square” - LED Inverse Square dimming curve

“Square” - LED Square dimming curve

Press the “ENTER” button to conrm the setting.

To choose between Halogen and LED dimmer curves, press the “MENU” button to show “DIMMODE” on

the LCD display. Press the “ENTER” button and use the “UP” and “DOWN” buttons to set the dimming

curve mode required.

“LED” - LED dimming curves

“HALOGEN” - Halogen dimming curves

To exit out of any of the above options, press the “MENU” button.

Manual mode:

To access manual mode, press the “MENU” button on to show “MANUAL” on the LCD display. The unit

is now in manual mode. Press the “ENTER” button and use the “UP” and “DOWN” buttons to set the

dimmer from “000” - “255”. Press the “ENTER” button and use the “UP” and “DOWN” buttons to set the

strobe from “000” - “255”.

(000 = LED off, 255 = LED at full brightness).

(000 = Strobe off, 255 = Strobe fast).

To exit out of any of the above options, press the “MENU” button.

Backlight:

To access the backlight setting, press the “MENU” button on the rear of the unit to show “BACKLIG” on

the LCD display. Press the “ENTER” button and use the “UP” and “DOWN” buttons to select between

“OFF” or “ON”. Press the “ENTER” button to conrm the setting.

To exit out of any of the above options, press the “MENU” button.

Software version:

To access the xtures software version, press the “MENU” button and use the “UP” and “DOWN” buttons

to show “Soft.Ver” on the LCD display. The unit will now display the xtures software version.

To exit out of any of the above options, press the “MENU” button.

Fixture temperature:

To access the xtures temperature, press the “MENU” button and use the “UP” and “DOWN” buttons to

show “TEMP” on the LCD display. The unit will now display the xtures temperature.

To exit out of any of the above options, press the “MENU” button.

Operating instructions

www.prolight.co.uk MP 120 LED Fresnel WW User Manual

Factory reset:

To access factory reset, press the “MENU” button on the rear of the unit to show “FacReset” on

the LCD display. Press the “ENTER” button and use the “UP” and “DOWN” buttons to select “Yes”.

Press the “ENTER” button to conrm the setting. The xture will reset to factory default settings. To exit

out of any of the above options, press the “MENU” button.

Operating instructions

www.prolight.co.uk MP 120 LED Fresnel WW User Manual

Setting the DMX address:

The DMX mode enables the use of a universal DMX controller. Each xture requires a “start address”

from 1- 512. A xture requiring one or more channels for control begins to read the data on the channel

indicated by the start address. For example, a xture that occupies or uses 7 channels of DMX and was

addressed to start on DMX channel 100, would read data from channels: 100, 101, 102, 103, 104,

105 and 106. Choose a start address so that the channels used do not overlap. E.g. the next unit in

the chain starts at 107.

DMX 512:

DMX (Digital Multiplex) is a universal protocol used as a form of communication between intelligent

xtures and controllers. A DMX controller sends DMX data instructions form the controller to the xture.

DMX data is sent as serial data that travels from xture to xture via the DATA “IN” and DATA “OUT”

XLR terminals located on all DMX xtures (most controllers only have a data “out” terminal).

DMX linking:

DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all xtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX xtures try to use the shortest

cable path possible. The order in which xtures are connected in a DMX line does not inuence the

DMX addressing. For example; a xture assigned to a DMX address of 1 may be placed anywhere in

a DMX line, at the beginning, at the end, or anywhere in the middle. When a xture is assigned a

DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that unit,

no matter where it is located in the DMX chain.

DATA cable (DMX cable) requirements (for DMX operation):

This xture can be controlled via DMX-512 protocol. The DMX address is set on the back of the unit.

Your unit requires either a standard 3-pin or 5-pin XLR connector for data input/output,

see images below.

Also remember that DMX cable must be daisy chained and cannot be split.

DMX setup

Further DMX cables can be purchased from all good sound and lighting suppliers or Prolight Concepts dealers.

Please quote: CABL10 – 2m CABL11 – 5m CABL12 – 10m3-Pin:

CABL185 – 2m CABL187 – 5m CABL188 – 10m5-Pin:

www.prolight.co.uk MP 120 LED Fresnel WW User Manual

Notice:

Be sure to follow the diagrams below when making your own cables.

Do not connect the cables shield conductor to the ground lug or

allow the shield conductor to come in contact with the XLRs

outer casing. Grounding the shield could cause a short circuit

and erratic behaviour.

Line termination:

When longer runs of cable are used,

you may need to use a terminator on

the last unit to avoid erratic behaviour.

Using a cable terminator will decrease

the possibilities of erratic behaviour.

(3-pin - Order ref: CABL90,

5-pin - Order ref: CABL89)

5-pin XLR DMX connectors:

Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-pin XLR xtures

may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a

3-pin line a cable adaptor must be used. The diagram below details the correct cable conversion.

5-pin XLR (female)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

3-pin XLR (female)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

3-pin XLR (male)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

5-pin XLR (male)

Pin 1: GND (screen)

Pin 2: Signal (-)

Pin 3: Signal (+)

Pin 4: N/C

Pin 5: N/C

DMX setup

Termination reduces signal

transmission problems and

interference. It is always

advisable to connect a DMX

terminal, (resistance 120

Ohm 1/4W) between pin 2

(DMX-) and pin 3 (DMX+) of

the last xture.

5-Pin

2 4

3-Pin

1 2

Pin Conguration

3-Pin 5-Pin

Pin 1 - Ground

Pin 2 - Negative

Pin 3 - Positive

– Pin 4 - N/C

– Pin 5 - N/C

DMX 512

3-Pin XLR output

DMX 512

3-Pin XLR input

GROUND

DMX +

DMX –

DMX 512

5-Pin XLR output

DMX 512

5-Pin XLR input

GROUND

N/C

DMX –

N/C DMX +

1 ground

3 hot

2 cold

3-Pin XLR male 3-Pin XLR female

2 cold

3 hot

1 ground

2 cold

1 ground 5 N/C

3 hot 4 N/C

5-Pin XLR male 5-Pin XLR female

4 N/C

5 N/C 1 ground

3 hot 2 cold

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Elumen8 Matériel de DJ

Elumen8

Elumen8 Virtuoso 2000 Fresnel RGBAL Manuel utilisateur

Elumen8

Elumen8 Virtuoso 1000 Profile WW Manuel utilisateur

Elumen8

Elumen8 Evora 600 Beam Manuel utilisateur

Elumen8

Elumen8 Evora CMY470 Hybrid Manuel utilisateur

Elumen8

Elumen8 MP60 LED Fresnel WW Manuel utilisateur

Elumen8

Elumen8 tz250 Manuel utilisateur

Elumen8

Elumen8 DB1300 Manuel utilisateur

Elumen8

Elumen8 Kudos 700 Beam Manuel utilisateur

Elumen8

Elumen8 Kudos 60 Beam Manuel utilisateur

Elumen8

Elumen8 Kudos 350ZS Manuel utilisateur

Elumen8

Elumen8 ELUM021 Manuel utilisateur

Elumen8

Elumen8 Titan Beam T3 Manuel utilisateur

Elumen8

Elumen8 Endura 1Q120 Manuel utilisateur

Elumen8

Elumen8 ELUM085 Manuel utilisateur

Elumen8

Elumen8 Evora Zoom Spot CMY300 Manuel utilisateur

Elumen8

Elumen8 MP180 LED Fresnel RGBALC Manuel utilisateur

Elumen8

Elumen8 Evora 850 Zoom Spot Manuel utilisateur

Elumen8

Elumen8 MP 15 LED Fresnel DTW Manuel utilisateur

Elumen8

Elumen8 TZ 250PC WW Manuel utilisateur

Elumen8

Elumen8 Evora 500 Spot Manuel utilisateur

Elumen8

Elumen8 Endura 1Q60 RGBW COB Exterior Fixture Manuel utilisateur

Elumen8

Elumen8 9RE Beam Manuel utilisateur

Manuels Matériel de DJ populaires d'autres marques

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuel du propriétaire

Chauvet

Chauvet OVATION E-930VW Manuel utilisateur

Zumtobel

Zumtobel APHRODITE Home Manuel utilisateur

Snow Masters

Snow Masters Zig Oscillator Manuel utilisateur

EuroLite

EuroLite 50530554 Manuel utilisateur

Beamz

Beamz BUV243 Manuel utilisateur

thomann

thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur

Eagletone

Eagletone 6 Eyes Flower Manuel utilisateur

EuroLite

EuroLite FLD-1508 Manuel utilisateur

Technical Pro

Technical Pro LG8xSEA Manuel utilisateur

JB Systems

JB Systems Lounge Laser DMX Manuel utilisateur

Lightmaxx

Lightmaxx Vega Halo 90 Manuel utilisateur

Elation

Elation FUZE WASH Z350 Manuel utilisateur

Maverick

Maverick MK3 WASH Manuel utilisateur

Infinity

Infinity TF-260C7 Fresnel Manuel utilisateur

Chauvet

Chauvet EVE E-50Z Manuel utilisateur

Eliminator Lighting

Eliminator Lighting E 138 Manuel utilisateur

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur