ELTEX RR-10 Manuel utilisateur
IP address:192.168.0.1
Username:admin
Password:password
Wi-Fi signal repeater
RR-10
User manual
Firmware version1.2.0
RR-10 wireless signal repeater. User manual
2
Contents
1 Device description......................................................................................................................4
1.1 Purpose.........................................................................................................................................4
1.2 Device specification .....................................................................................................................4
1.2.1 Connection diagrams for RR-10 ........................................................................................... 5
1.2.2 RR-10 use case:...................................................................................................................... 6
1.3 Technical features........................................................................................................................6
1.4 Design ...........................................................................................................................................8
1.4.1 Front panel of the device. State indication ......................................................................... 8
1.4.2 Rear panel of the device. LAN connection indication ......................................................... 8
1.4.3 Bottom panel of the device .................................................................................................. 9
1.5 Resetting to factory settings......................................................................................................10
1.6 WPS button management .........................................................................................................10
1.7 Delivery package ........................................................................................................................10
2 Installation order .....................................................................................................................11
2.1 Safety rules.................................................................................................................................11
2.2 Installation recommendations..................................................................................................11
2.3 Connecting RR-10 to a network.................................................................................................12
2.3.1 Method 1. UsingWPS button.............................................................................................. 12
2.3.2 Method 2. Via web interface in repeater mode.................................................................. 12
2.3.3 Method 3. Via web interface in access point mode ........................................................... 14
2.4 EasyMesh agent mode ...............................................................................................................15
2.4.1 Connecting to EasyMesh network using WPS button ....................................................... 15
3 Device management via the web interface ..........................................................................17
3.1 Getting started ...........................................................................................................................17
3.2 Device control panel ..................................................................................................................18
3.3 Repeater mode...........................................................................................................................19
3.3.1 The «Status» tab.................................................................................................................. 19
3.3.2 The «Wi-Fi» tab .................................................................................................................... 21
3.3.3 The «Network» tab .............................................................................................................. 25
3.3.4 The «System» tab ................................................................................................................ 26
3.4 EasyMesh agent mode ...............................................................................................................28
3.4.1 The «Status» tab.................................................................................................................. 28
3.4.2 The «EasyMesh» tab ............................................................................................................ 29
4 Problems and solutions...........................................................................................................30
RR-10 wireless signal repeater. User manual
4
•
•
•
•
•
•
•
•
•
1 Device description
1.1 Purpose
RR-10 – universal wireless signal repeater designed to expand the coverage area of wireless networks and
amplify Wi-Fi signal. The device allows you to eliminate blind spots and optimize the performance of your Wi-Fi
network.
With support for IEEE 802.11n/ac standards, RR-10 repeater provides high data transfer rates and is capable to
provide high-quality multimedia transmission of 4K content. The use of MIMO technology and internal
antennas makes RR-10 a universal solution for expanding your home network.
RR-10 supports EasyMesh technology and can be used in EasyMesh network as an agent.
1.2 Device specification
The device is powered by an external 5.3V adapter from 220V power network.
Interfaces:
LAN: 1 port of Ethernet RJ-45 10/100/1000BASE-T;
WLAN: IEEE 802.11b/g/n 2.4 GHz and 802.11a/n/ac 5 GHz.
Functions:
Support for WPA/WPA2 encryption standards;
Support for WMM;
Support for WPS;
Wireless Multicast Forwarding;
Support for Wi-Fi IEEE 802.11a/b/g/n/ac/k/v;
MIMO 2x2;
EasyMesh.
RR-10 wireless signal repeater. User manual
5
1.2.1 Connection diagrams for RR-10
2.4 GHz repeater:
5 GHz repeater:
Access point:
RR-10 wireless signal repeater. User manual
6
1.2.2 RR-10 use case:
1.3 Technical features
General parameters
Processor Realtek R TL8197F S -V G
Clock frequency 1 GHz
RAM 128 MB
ROM 16 MB
Operating system Linux 3.10
LAN Ethernet interface parameters
Number of interfaces 1
Connector type RJ-45
Data rate, Mbps 10/100/1000, autonegotiation
Agent in EasyMesh network
When used with the RG-35-WZ router (firmware version 2.2.0 or later), the RR-10 repeater will act as
an EasyMesh agent after being configured via WPS.
RR-10 wireless signal repeater. User manual
7
Standards BASE - T
Wireless interface parameters
Number of antennas 2
Antenna type internal
Standards 802.11 a/b/g/n / ac/k/v
Frequency range 2412-2472 MHz
5180-5320 MHz
5660-5825 MHz
MIMO 2. 4 MHz 2х2
5 MHz 2х2
Modulation 2,4 MHz: DSSS, CCK, BPSK, QPSK, 16QAM, 64QAM
5 MHz: BPSK, QPSK, 16QAM, 64QAM, 256QAM
Data transfer rate 802.11b: up to 11 Mbps
802.11 a: up to 54 Mbps
802.11 g: up to 54Mbps
802.11 n ( HT 20): up to 144Mbps
802.11 n ( HT 40): up to 300Mbps
802.11 ac ( HT 80): up to 866Mbps
Maximum transmitter output power 12.4 GHz: up to 18 dBm
5 GHz: up to 20 dBm
Receiver sensitivity 2.4 GHz: up to -98 dBm
5 GHz: up to -96 dBm
Security WPA (TKIP+AES), WPA2 (TKIP+AES), WPA/WPA2
(TKIP+AES)
Control
Remote control web interface
Access restriction by password
Physical specifications
Power external 5.3V DC, 2Аpower adapter
Maximum power consumption 7 W
Range of operation temperatures from +5 to +40°C
Relative humidity at 25°C up to 80%
Dimensions (Diameter x Height) 100 x 23 mm
Weight 85 g
1The value of the maximum output power will vary according to the rules of radio frequency regulation in your
country
RR-10 wireless signal repeater. User manual
8
1.4 Design
RR-10 wireless signal repeater is implemented in a plastic case with dimensions ofØ100 x 23 mm.
1.4.1 Front panel of the device. State indication
Front panel of RR-10
Description of front panel LED indicators
#LED LED status Device state
1 LED shows the device
operation status
Solid red The device is launching (1 minute max.)
Red, flashing rapidly The device is updating/reseting
Red, flashing slowly The device is turned on, there is no connection to the
access point (router)
Green, flashing rapidly The device is connecting to an access point (router)
through WPS technology
Green, flashing slowly The device is connected to an access point (router), no
access to the Internet
Solid green The device has been connected to an access point
(router) and has access to the Internet
1.4.2 Rear panel of the device. LAN connection indication
Rear panel of RR-10
RR-10 wireless signal repeater. User manual
9
#Rear panel element Description
1 Button for client connection via the WPS protocol
2 LAN 10/100/1000BASE-T (RJ-45) port for connection to external networks
3 LEDs LAN connector indicators
4 5v DC Connector for power adapter connection
LAN connection indication
LED status Device state
Only green lights The connection is established at 10/100 Mbps
Green and orange lights The connection is established at 1000 Mbps
Flashes green The process of packet data transmission through LAN interface
1.4.3 Bottom panel of the device
Bottom panel of RR-10
Description of bottom panel controls
#Bottom panel element Description
1 F Button for reseting to factory settings
RR-10 wireless signal repeater. User manual
10
•
•
•
1.5 Resetting to factory settings
To reset the device to factory settings, press and hold the «F» button for more than 3 seconds until the
indicator on the front panel flashes red.The device will automatically restart within 5 seconds, and the
indicator will light up red. When the device is ready, the indicator flashes red slowly.
1.6 WPS button management
The device supports connection to the router Wi-Fi networks via WPS. To configure the connection, activate
the WPS function on the router and press and hold the WPS button on the back of the device for 3 seconds.
After that the device will connect to the router automatically. Connection to the router takes no more than two
minutes. In case the connection is not successful, try again and make sure that the WPS function on the
repeater was activated no later than 2 minutes after the WPS function was activated on the router.
1.7 Delivery package
RR-10 standard delivery package includes:
RR-10 wireless signal repeater;
230/5.3V 2.0A power adapter;
Device quick configuration guide.
By default, the DHCP server is running on all interfaces;
LAN interface address is 192.168.0.1;the subnet mask is 255.255.255.0;
the username/password for access via the web interface: admin/password.
Configuring with WPS technology as a client is only available for non-configured devices. Before
using the WPS button, you must reset the device to the factory settings.
After configuring the device, a DHCP client is launched on all interfaces.
Autres manuels pour RR-10
1
Table des matières
Autres manuels ELTEX Répétiteur
