Remo 8 wireless remote control 1
Remo 8 hand-held transmitter software version 1.1 and up • Issued 28/07/2011 • The right to make technical changes is reserved. Errors excepted.
Elsner Elektronik GmbH • Herdweg 7 • D-75391 Gechingen • Germany • Phone: +49 (0) 70 56/93 97-0 • Fax: -20 • info@elsner-elektronik.de • www.elsner-elektronik.de
1. Description
The Remo 8 wireless remote control offers an Up/Down/Stop or On/
Off control for eight channels and can be set up with vari-
ous devices. If the remote control is not being used, it is sa-
fely placed in the included magnetic wall-holder.
Remo 8 is suitable for the following devices:
• WS1000 Color control (version 1.1 and up), WS1 Color
• Solexa control (v. 3.6 and up), Arexa (v. 3.7 and up)
• WL305, WL610 ventilators (version 4.0 and up), WFL
air supply (version 2.0 and up)
• RF-Relay (version 2.0 and up), RF-MSG motor control
unit, RF-VM ventilation module
• XS MSG2-AP wireless motor control unit (v.2.0 and up)
• Lixa control unit
The software version of the device must be appropriate for interaction
with the remote control!
Moisture is harmful to the electronic components of
the hand-held transmitter. You must therefore:
• Not leave it in the rain
• Not leave it outside overnight
• Protect it from frost
1.1. Scope of delivery
• Hand-held transmitter with battery
• Wall-mounted holder with screw covers
1.2. Technical data
The following standards were consulted during the evaluation of this
product with respect to electromagnetic compatibility:
• EN 301 489-1 V1.8.1:2008-04
• EN 300 220-2 V2.1.2:2007-06
The product was tested by an accredited EMC-lab in compliance with
the above-named standards.
2. Installation and commissioning
2.1. Installing the wall-mounted holder
2.2. Notes on radio devices
The design of radio communication devices must pay attention to suf-
ficient radio signal reception. The range of radio controls is limited by
legal regulations applicable to radio devices and by local structural con-
ditions. Avoid source of disturbance and obstacles between transmitter
and receiver that could disrupt radio communication. These include for
example:
• Walls and ceilings (especially concrete).
• Metallic surfaces close to the radio network participant (e.g.
aluminum frame of a winter garden).
• Other network participants and strong local transmitting devices
(e.g. radio headphones) transmitting on the same frequency (868.2
MHz). Therefore, keep a minimum distance of 30 cm between
radio transmitters.
2.3. Configuring and deleting a connection
Each of the hand-held transmitter's eight channels can control one or
more radio channels (units).
2.3.1. WS1000 Color / WS1 Color control systems
Configuration:
Deletion:
2.3.2. XS MSG2-AP motor control unit
Configuring and deleting should only be performed
by a trained electrician!
Configuration:
Deletion:
Housing Plastic
Colours • white/light grey
• aluminium/graphite (partially painted)
Installation with magnetic wall-holder
Protection category IP 40
Dimensions Transmitter approx. 41 x 140 x 21 (WxHxD,
mm), Holder approx. 54 x 150 x 11 (WxHxD,
mm)
Total weight approx. 95 g
Ambient temperature Operating 0…50 °C, storage -10…+60 °C
Ambient humidity max. 95% rH, avoid condensation
Operating voltage 3 V CR2032 type battery
Radio frequency 868.2 MHz
Channels 8
The holder must be firmly screwed to the wall.
Please use suitable dowels and screws as
supports. The screws should then be covered
with the provided screw covers.
The hand-held transmitter is held in position in
its tray with magnets.
1. Bring the control unit into the set-up readiness state: Menu
System > Installation > Wireless connection > Setup.
Please also follow the instructions in the manual.
2. Press the centre of the +/- button on the hand-held
transmitter until an "S" for Setup and a number
(channel) are displayed.
The channel selected will not affect the configuration of
the WS1000 Color/WS1 Color.
3. Press the Up arrow button to establish the wireless
connection with the control system.
4. The remote control is now configured for the control system.
The System > Installation > Wireless connection > Status menu
item allows you to give the hand-held transmitter a separate
name and assign individual drives and devices to the hand-held
transmitter channels.
1. Delete the hand-held transmitter on the control system menu:
Menu System > Installation > Wireless connection > Delete.
Please also follow the instructions in the manual.
1. Bring the desired channel of the motor control unit into the set-
up readiness state (see manual chapter "Motor control unit
wireless connection
- Remo 8").
2. Bring the hand-held transmitter into the set-up
readiness state by pressing the centre of the +/- button
on the hand-held transmitter until an "S" for Setup and
a number (channel) are displayed.
3. Using + or - change the hand-held transmitter channel
that you would like to connect to the motor control unit
channel (L 1 to L8).
4. Press the Up arrow button to establish the wireless
connection with the motor control unit.
The hand-held transmitter channel is now configured
to the channel of the motor control unit.
1. Bring the desired channel of the motor control unit into the set-
up readiness state (see manual chapter "Motor control unit
wireless connection - Remo 8").
2. Bring the held-held transmitter into the deletion
readiness state. For this purpose press the +/- button in
the centre till "S" appears in the display. Then press
again till a "C" for Clear appears in the display.
3. Using + or - change to the hand-held transmitter that
you want to delete (C 1 to C 8).
4. Press the Up arrow button to delete the wireless
connection to the motor control unit channel.
