Elsner IP KNX interface Manuel utilisateur
IP KNX interface
for Mobotix IP cameras
Technical specifications and installation instructions
Item number 70199
EN
Elsner Elektronik GmbH Control and Automation Engineering
Sohlengrund 16
Germany Fax +49 (0) 70 33 / 30 945-20 www.elsner-elektronik.de
Technical service: +49 (0) 70 33 / 30 945-250
2 Description
IP KNX interface • Version: 13.03.2017 • Technical changes and errors excepted.
1. Description
The IP KNX interface serves to transmit data between the Mobotix IP cameras and
the KNX bus system. For this purpose, the KNX telegrams are converted into the Ether-
net protocols and sent to the LAN in which the cameras are installed (and vice versa).
Features:
• Communication with 8 IP cameras with 8 input and 8 output objects each
• Transfer of the camera events to the KNX bus
• Controlling the camera via the KNX bus
• KNX Bus Terminal and Ethernet / IP Connection (POE)
• Suitable for IP cameras that meet the communication requirements as
described in the camera settings in the manual
Configuration is made using the KNX software ETS. The product file can be downloa-
ded from the Elsner Elektronik website on www.elsner-elektronik.de in the “Ser-
vice” menu.
1.0.1. Scope of delivery
•IPKNXInterface
1.1. Technical specifications
The product is compliant with the provisions of EC guidelines.
Housing Plastic
Colour White
Assembly Series installation on a mounting rail
Protection category IP 20
Dimensions approx. 53 x 88 x 60 (W x H x D, mm), 3 modules
Weight approx. 110 g
Ambient temperature Operation at 0...+65°C, storage at -40...+70°C
Ambient humidity max. 90% RH, avoid condensation
Operating voltage • POE (Power Over Ethernet), IEEE 802.3af, Category 1
• KNX bus voltage
Power on bus: 10 mA
Ethernet/IP connection LAN jack RJ45
KNX bus connection KNX +/- bus connector terminal
BCU type integrated micro-controller
PEI type 0
Group addresses max. 1,024
Assignments max. 1024
Communication objects 897
3 Installing and commissioning
IP KNX interface • Version: 13.03.2017 • Technical changes and errors excepted.
2. Installing and commissioning
2.1. Installation notes
Installation, testing, operational start-up and troubleshooting should
only be performed by an electrician.
CAUTION!
Live voltage!
There are unprotected live components inside the device.
• National legal regulations are to be followed.
• Ensure that all lines to be assembled are free of voltage and take
precautions against accidental switching on.
• Do not use the device if it is damaged.
• Take the device or system out of service and secure it against
unintentional use, if it can be assumed, that risk-free operation is no
longer guaranteed.
The device is only to be used for its intended purpose. Any improper modification or
failure to follow the operating instructions voids any and all warranty and guarantee
claims.
After unpacking the device, check it immediately for possible mechanical damage. If it
has been damaged in transport, inform the supplier immediately.
The device may only be used as a fixed-site installation; that means only when assem-
bled and after conclusion of all installation and operational start-up tasks and only in
the surroundings designated for it.
Elsner Elektronik is not liable for any changes in norms and standards which may occur
after publication of these operating instructions.
4 Installing and commissioning
IP KNX interface • Version: 13.03.2017 • Technical changes and errors excepted.
2.2. Setting up and connecting the device
2.3. Instructions for assembly and initial start-up
Never expose the device to water (e.g. rain). This can damage the electronics. A relative
air humidity of 90% must not be exceeded. Avoid condensation.
After the operating voltage has been applied, the device will enter an initialisation pha-
se lasting a few seconds. During this phase no information can be received or sent via
the bus.
Fig. 1
Series installation on the mounting rail (3
TE)
1) IP connector
2 Programming LED and programming
buttons (PRG)
3) Bus terminal slot (KNX +/-)
4) Power LED (supply voltage/Bus)
3
4
1
2
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Elsner Équipement d'enregistrement
Manuels Équipement d'enregistrement populaires d'autres marques
Strymon
Strymon NIGHTSKY Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuel utilisateur
Tews Technologies
Tews Technologies TPMC465 Manuel utilisateur
Honeywell
Honeywell Excel 50 Manuel utilisateur
SeaLevel
SeaLevel COMM+8.LPCI Manuel utilisateur
Arturia
Arturia AUDIOFUSE STUDIO Manuel utilisateur
