Elsema Intelligent Swing iS400 Manuel utilisateur



iS400/iS400D/iS400SolarSWINGGATEOPENERMANUAL

iS400 / iS400D / iS400Solar

SWING GATE OPENER with LIMIT SWITCH

USER MANUAL



iS400/iS400D/iS400SolarSWINGGATEOPENERMANUAL

INDEX

1.1 GENERAL SAFETY PRECAUTION ...........................................................P.1

1.2 INSTALLATION

A. STANDARD INSTALLATION ................................................................P.2

B. INSTALLATION CHECK .......................................................................P.3

C. REAR BRACKET INSTALLATION .......................................................P.4

D. FRONT BRACKET INSTALLATION …………......................................P.4

E. MOTOR FIXING .....................................................................................P.5

F. WIRE CONNECTION .............................................................................P.5

G. EMERGENCY RELEASE ......................................................................P.6

H. LIMIT SWITCH ADJUSTMENT .............................................................P.6

1.3 TECHNICAL FEATURES

A. TECHNICAL FEATURES .....................................................................P.7

B. DIMENSION ..........................................................................................P.7

1.4 MAINTENANCE ..........................................................................................P.8



iS400/iS400D/iS400SolarSWINGGATEOPENERMANUAL

1.1 GENERAL PRECAUTION

WARNING:

This user manual is only for qualified technicians who are specialized in

installations and automations.

1) All installations, electrical connections, adjustments and testing must be

performed only after reading and understanding of all instructions carefully.

2) Before carrying out any installation or maintenance operation, disconnect the

electrical power supply by turning off the mains switch connected upstream

and apply the hazard area notice required by applicable regulations.

3) Make sure the existing structure is up to standard in terms of strength and

stability.

4) When necessary, connect the motorized gate to reliable earth system during

electricity connection phase.

5) Installation requires qualified personnel with mechanical and electrical skills.

6) Keep the automatic controls (remote, push buttons, key selectors. Etc) placed

properly and way from children.

7) For replace or repair of motorized system, only original parts must be used.

Any damage caused by inadequate parts and methods will be not claimed to

motor manufacturer.

8) Never operate the drive if you suspect that it might be faulty or will cause

damage to the system.

9) The motors are exclusively designed for gate opening and closing

application, any other usage is deemed inappropriate. The manufacturer will

not be liable for any damage resulting from the improper use. Improper usage

should void all warranty, and the user accepts sole responsibility for any risks

thereby may accrue.

10) The system may be operated in proper working order. Always follow the

standard procedures by following the instructions in this installation and

operating manual.

11) Only operate the remote when you have the full view of the gate.

ELSEMA PTY LTD shall not be liable for any injury, damage, or any claim to

any person or property which may result from improper use or installation

of this system.

Please keep this installation manual for future reference.

1



iS400/iS400D/iS400SolarSWINGGATEOPENERMANUAL

1.2 STANDARD INSTALLATION

A. STANDARD INSTALLATION

2



iS400/iS400D/iS400SolarSWINGGATEOPENERMANUAL

B. CHECKS BEFORE INSTALLATION

Before proceeding with the installation check the following:

1) Check that the motor mounting position on the gate pillar can be done with the measurements

in Figure 1 and Graph 1

2) Be sure that gate moves freely

3) There are no obstacles in the moving gate area

4) Hinges are properly positioned and greased

5) There should be no friction between the gate leaf’s

6) There should be no friction with the ground while moving the gates

7) Check that the gate structure is suitable to install automatic gate motors

8) “C” value is 140mm

9) “D” can be measured from the gate easily

10) “A” = “C” + “D”

11) The value of “B” can be calculated from the value of “A” and the leaves opening angle

**Please make sure “B” and “A” are similar or the same in value that the leaf’s can be operated

smoothly, also to reduce the burden of the motor.

Fig 1 Graph 1

3



iS400/iS400D/iS400SolarSWINGGATEOPENERMANUAL

C. INSTALLATION OF REAR BRACKET

Step 1: Before securing the rear bracket to the pillar check the front bracket can be welded to a solid point

on the gate leaf.

Fully close the gate.

Connect the rear and front brackets to the motor.

Hold the rear bracket onto the pillar with the calculated Aand Bvalues.

Move the motor in a vertical direction until the fixing zone is in a solid area of the gate leaf for

the front bracket.

Step 2: Then fix the rear bracket to the pillar.

D. INSTALLATION OF FRONT BRACKET

For proper operation, the front bracket should be fixed so the motor has the correct angle. Use Table 1 to

calculate the location of the front bracket.

Table 1

(

)

(

)

190 1330

200 1320

210 1310

220 1300

230 1290

240 1280

250 1270

260 1260

270 1250

4



iS400/iS400D/iS400SolarSWINGGATEOPENERMANUAL

E. MOTOR FIXING

While the motor is disengaged, remove the wire cover and fix the rear bracket with the pin. The

pin will slot into the hole with the threaded side up as shown in no.1. No screw is required to

hold the pin in place. Attach the front bracket to the drive unit with the pin (A) and the set screw

(B) provided as shown in no.2

Make sure the motor is mounted in a horizontal position, especially in these positions:

1) Gate in “CLOSE” position

2) Gate in “OPEN” position

3) Gate at “45° angle” position

Prior to welding the bracket on the gate leaf (if necessary), cover the gate opener to prevent

damages from sparks.

F. WIRE CONNECTION

Avoid tension in the cable during opening and closing cycles

Limit switches are Normally Closed Type.



5



iS400/iS400D/iS400SolarSWINGGATEOPENERMANUAL

G. EMERGENCY RELEASE

In case of power failure, slide the lid of the manual release chamber forward. Insert the key and

turn clockwise to unlock, and then turn around the knob to release.

H. LIMIT SWITCH ADJUSTMENT

After installation of the motor and the bracket, navigate to the “Tools” option on the control card and to “Test

Inputs”. Manually move the gate to fully open and closed position and make sure the Limit switch input is

activated. Move the Limit switch if needed. The gate will stop in the position at which the control card detects

the limit switch activation. Input name will change to “UPPER CASE” when it is activated.

Step1. Slide the lid of the release chamber forward

Step2. Insert the key and turn clockwise into the unlock position

Step3. Then turn the knob clockwise to release the motor.

Make sure the white bar on the knob is on the position opposite to the

triangle indicator.

To restore the automation, simply reverse the above procedure.

6



iS400/iS400D/iS400SolarSWINGGATEOPENERMANUAL

I. ELECTRICAL CONNECTION

After successful motor installation, refer to the user manual of the control card

for automatic operation setup.

1.3 TECHNICAL FEATURES:

A. Technical Features:

B Dimension:

Motor Voltage 24Volts DC motor

Gear Type Worm gear

Max Absorbed Power 144 Watts

Peak Thrust 4500N

Nominal Thrust 4000N

Stroke Length (CD) 450mm

Power Supply 240 Volts AC

Nominal Input Current 2 Amps

Maximum Operating Current 5.5 Amps for maximum 10 sec

Maximum Gate Weight 450 kg per leaf

Maximum Gate Length 4.5 metres

Duty Cycle 20%

Operating Temperature -20°c ~ +50°c

Dimension 1110mm x 123mm x 124mm

7



iS400/iS400D/iS400SolarSWINGGATEOPENERMANUAL

1.4 MAINTENANCE:

Maintenance should be performed at least every six months. If it is used in high traffic area, a

more regular maintenance should be performed.

Disconnect the power supply:

(1) Clean and lubricate the screws, the pins and the hinge with grease.

(2) Check the fastening points are properly tightened.

(3) Check and make sure that the wire connections are in good condition.

Connect the power supply:

(1) Check the power adjustments.

(2) Check the function of the manual release

(3) Check the photocells or other safety device.

Service History

Date Maintenance Installer

8

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Elsema ouvre-porte de garage

Elsema

Elsema Eclipse MC Series Manuel

Manuels ouvre-porte de garage populaires d'autres marques

Dorma

Dorma ES 90 Manuel utilisateur

Garaga

Garaga SECURITY+ 3265GCM 1HP Manuel utilisateur

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Manuel utilisateur

Chase Doors

Chase Doors DuraShield Manuel utilisateur

CSI

CSI Classic Manuel utilisateur

HATO

HATO 120 Manuel utilisateur

Chamberlain

Chamberlain Elite 3575S Manuel utilisateur

Richmond

Richmond GTR156 Manuel utilisateur

Raynor

Raynor 1280RGD Manuel utilisateur

CAME

CAME F4000 Series Manuel utilisateur

B&D

B&D Controll-A-Door 5 Manuel utilisateur

BFT

BFT PRV AA SL Manuel utilisateur

Craftsman

Craftsman 139.53924 Manuel utilisateur

Chamberlain

Chamberlain MyQ 940ESTD Manuel utilisateur

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Manuel utilisateur

Westfalia

Westfalia 19 36 07 Manuel utilisateur

Chamberlain

Chamberlain HD520EVP Manuel utilisateur

Cardin

Cardin BL Series Manuel utilisateur