elnitor RoadSpark slim Mode d’emploi
RoadSpark slim
mounting manual
Luminaire maintenance and servicing
Luminaire internal parts are durable and require no maintenance. If required, the luminaire
shield can be wiped or washed at a distance.
Warranty
Standard warranty – 5 years;
Warranty does not apply to mechanical damages, e.g. scratches;
It is possible to receive an extended warranty based on additional agreement.
IMPORTANT: Luminaire servicing only to be conducted by certified personnel!
• SIA Elnitor • Latvia (EU) • Phone: (+371) 6 606 56 31 • e-mail: elnitor@elnitor.lv • www.elnitor.lv •
℗2015 elnitor
Setting up
The standard mode of operation is as follows:
switch on-offfrom night-sensor, with automatic
dimming to 50% intensity from 01:00 until 05:00.
Settings may be changed based on clients timely
request. In case settings need to be changed
aſter installation, this can be done by using
RoadSpark MCU programming unit.
Troubleshooting
PROBLEM
POSSIBLE REASONS
SOLUTION
Luminaire does not
switch on in test
mode
There is no electricity
in the circuit
Check connection to
electrical power
supply
Luminaire does not
switch on during
nighttime
Incorrect settings of
the astronomical
clock
Check connection to
electrical power
supply
Luminaire does not
switch on during
nighttime
Incorrect grouping
programming
Check and correct
clock settings
Luminaire does not
switch on during
nighttime
No radio channel
connection
Change luminaire
group accordingly
Luminaire does not
switch on during
nighttime
there is no electricity
in the circuit
Check distance to the
next operating
luminaire
Luminaire does not
dim at “deep” night
Dim time is not set
Input the dim time
parameter
Cautions
It is forbidden to:
- use a power supply with different parameters from the originally installed;
- servicing of the lamp by unqualified personnel;
- block nigh-sensor;
- use inadequate lamp pole bracket or other luminaire bracket;
- connect the lamp to circuit under voltage. The luminaire must be connected to the circuit
first, and only then voltage is to be applied.
Bracket mounting
Pole-top
mounting
General data
LED luminaire is to be used for street lighting,
pedestrian and bicycle routes. The LED luminaire
is fitted with radio channel. The luminaire set
includes the luminaire (1 unit), mounting manual
(1 unit).
Mounting
WARNING: luminaire to be installed by qualified
personnel! Use installation gloves!
1. Insert the cable from the luminaire on the
inside of the console inside the pole.
2. Loosen two screws (a, b), put an arm on the
console until it stops, tighten the two screws (a,
b), then tighten the lock nut.
3. If necessary to change the angle of the lamp,
release the two screws (a, d), release the two
side bolts (e, f), tool set RSL (optional) to set the
angle of the light, put on the device RSL right
angle, turn the light up coincidence of levels (g,
h), and to tighten the two screws (c, d), and then
tighten the two lateral bolts (e, f).
4. Behind hatch at the bottom of the pole (tower),
connect the cable from the lamp to the cable
from the power supply (i) via connectors (j, k),
according to the polarity of the color of the
cable according to the markings on the power
supply (i).
5. Connect the power supply cable to the
automatic fuse in the pole (tower).
6. Lower the power supply into the hatch on the
bottom of the pole (tower).
Manuels Équipement d'éclairage populaires d'autres marques
Qazqa
Qazqa Suplux SL 3 Black 103062 Manuel utilisateur
Commercial Electric
Commercial Electric 54568141 Manuel utilisateur
CREE LIGHTING
CREE LIGHTING 304 Series Manuel utilisateur
Goobay
Goobay 49867 Manuel utilisateur
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manuel utilisateur
Alkalite
Alkalite Krypton KT-81 Manuel utilisateur
