Ellard Fire Door Control Panel Feuille d'instructions

PRODUCT INSTRUCTIONS

Fire Door Control Panel (FDCP) Floats Rd, Wythenshawe,

Manchester. M23 9WB

T: +44 (0)161 945 4561

F: +44 (0)161 945 4566

Stock Code Description Doc No: PI-115

00133

00134 Ellard Fire Door Control Panel

Ellard Slave Repeater Unit Iss: 1

FDCP V.1

Contents

1) Specification and Installation ....................................................................................

2) Connection and Indication ...........................................................................................

2.1 Mains Power Supply - In....................................................................................

2.2 Mains Supply - Out.............................................................................................

2.3 Battery...............................................................................................................

2.4 Fire Alarm Signals...............................................................................................

(2.4.1) Zone 1

(2.4.2) Zone 2

2.5 Push Button Connection....................................................................................

2.6 Key Switch Connection......................................................................................

2.7 Panic Button.......................................................................................................

2.8 Photo Beam.......................................................................................................

2.9 Relays................................................................................................................

2.10 Solenoid Release Output .................................................................................

3) Motor Configuration Examples ....................................................................................

3.1 230v AC Tubular Motors

3.2 24v d.c Tubular Motors

3.3 JM Fire shutter Motors

3.4 Volt Free (Other Motors with built on controlers)

4) Smoke and Heat Detector Configurations ...................................................................

5) Programing ...................................................................................................................

6) Repeater Panel...............................................................................................................

6.1 Connection to Repeater Panel

7) Trouble Shooting...........................................................................................................

Power Supply

General

230v - 50Hz

Working Temp

Max Accessories Load

Protection Fuses

1) Specification and Installation

Max Motor Load

Dimensions (mm)

3.0

Weight (Kg)

Batteries 2 x 12V 1.3Ah

Ext 24v d.c: F1 = T4A, Delayed

Mains: F2 = T200mA, Delayed

Relays: F3 = T6.3A, Delayed

236 (w) x 286 (h) x 108 (h)

6.3A @ 230v

4A @ 24v d.c

Cable Entry

The FDCP is designed so the cable entry can be positioned at

the top or bottom of the panel by means of removing the PCB

fixing screws, then rotating either board or box 180° and

refitting (see Fig 1.2)

Mounting

Mount the unit using the fixing holes provided (see Fig 1.1)

BOTTOM CABLE ENTRY

'A'

Fig 1.1

Enclosure Mounting

TOP CABLE ENTRY

Fig 1.2

Cable entry positions

Remove fixing screws 'A' and rotate

board or box

WARNING

FIRE

SHUTTER

CLOSING

Standards and Conformity

Directive 2004/108/EC

Directive 2006/95/EC

EMC Directive:

Low Voltage Requirements:

and In association with: EN 60204-1: 2006+A1: 2009

EN 61000-6-1: 2007

EN 61000-6-2: 2005

EN 61000-6-3: 2007+A1: 2011

EN 61000-6-4: 2007+A1: 2011

EN 12453:2001

EN 50272-2: 2001

The FDCP complies to the following EMC and Low Voltage

standards and directives

-20 to +70°C

Connection - TS3A

Mains power supply - EARTH

Mains power supply - LIVE

Mains power supply - NEUTRAL

Connection - TS3

Mains power supply - EARTH

Mains power supply - LIVE

Mains power supply - NEUTRAL

Ext. Siren

Connection - TS5

Ext. Warning Light

Ext. 24v d.c

1Zone 1 - Main Fire signal +24v d.c (+)

Connection - TS1

11 Push Button - COM

Connection - TS1A

15 + 16

Photo Beam Supply - (+24v)

Photo Beam Contact - ( COM)

Zone 1 - Main Fire signal - N/O, N/C, 8k2

Zone 2 - Local Fire signal +24v d.c (-)

Zone 2 - Local Fire signal N/O, N/C, 8k2

Ext. 24v d.c. Supply (200mA Max)

Push Button - STOP (N/C)

Push Button - OPEN (N/O)

Push Button - CLOSE (N/O)

Panic Button - (N/O)

Photo Beam Supply - (0V)

Photo Beam Contact - ( N/C)

3 + 4

7 + 8

9 + 10

1 + 2

3 + 4

5 + 6

1 + 2 Stop Relay (N/C)

Connection - TS6

Open Relay (N/O)

Aux 1 Relay (N/C)

3 + 4

5 + 6

Close Relay (N/O)

Aux 1 Relay (COM)

Aux 1 Relay (N/O)

Aux 2 Relay (N/C)10

Aux 2 Relay (COM)

Aux 2 Relay (N/O)

Solenoid (0V)

Solenoid (+24V)14

+Battery (+)

Connection - TS4

Battery (-)-

2 Zone 1 - Main Fire signal +24v d.c (-)

Zone 2 - Local Fire signal +24v d.c (+)

Mains ok

Indication

Fault

Alarm

FDCP v.1 (Software Ver 06)

Multi Function Control System for Roller Shutters and

Smoke curtains

Features

·Large visual warning 'FIRE SHUTTER CLOSING' and

102 dB sounder

·Internal easy read display

·Easy to program using the 'intelligent' dial

·Built in batteries to maintain fire signal activation, and to

operated a 24v brake release device in the even of a

power failure

·Select able fire signal - Normally Open (N/O) or

Normally Closed (N/C) volt free potential (Dry contact)

or 2 -30V d.c direct input

·Low Voltage external push button control

·3 closing options - Solenoid Only, Power Closing or 2

Stage Drop

·Programmable relays

·Automatic reset and optional opening once the fire

signal is removed

·Panic Button option for emergency escape

·Complies with latest EU Directives

·Fully CE compliant

Application

·Whilst maintaining the function of every day use the

FDCP gives advanced warning in the event of a fire

before closing the shutter or curtain, protecting both

personnel and property from the effects of smoke and

fire

·Built in comprehensive diagnostics which include mains

fail and low battery charge

·Can be fully interfaced with building management

systems

Installation

·The enclosure should be mounted vertically and

secured using the provided fixing holes (see fig 1.1)

·Consideration must be given to the incoming cables

and the panel rotated accordingly to give top or bottom

entry (see fig 1.2)

·To protect both motor and personnel, this product must

be connected to a suitable EARTH point

·All electrical work should be undertaken by a suitable

competent person

2) Connections and Indication

GREEN Automatic when mains power applied

RED

Switched on when Alarm Signal applied

Switched on when a fault has occurred

(see display message for more information)

Stop ok RED On if Stop circuit - ok

Photo ok GREEN On if Photo Beam circuit - ok

(+24)

(-)

(+24)

(-)

Fig 3. Activation by removal of a

Permanent +24v d.c Fire Signal

(Select +24V)

2.4) Fire Signals (Connections and types)

2.4.1) Alarm Zone 1 - Main Fire Alarm Signal

Normally Open (N/O)

Triggers the panel by a N/O volt free signal which CLOSES

when the fire alarm is activated

Note: an 8k2 resistor must be fitted across input

connections

Normally Close (N/C)

Triggers the panel by a N/C volt free signal which OPENS

when the fire alarm is activated

+24v d.c

Triggers the panel by removing a permanently connected +24v

d.c fire signal when the fire alarm is activated

2.4.2) Alarm Zone 2 - Local Fire Alarm Signal

Normally Open (N/O)

Triggers the panel by a N/O volt free signal which CLOSES

when the fire alarm is activated

Note: an 8k2 resistor must be fitted across input

connections

Normally Close (N/C)

Triggers the panel by a N/C volt free signal which OPENS

when the fire alarm is activated

+24v d.c

Triggers the panel by removing a permanently connected +24v

d.c fire signal when the fire alarm is activated l

OFF

Disables Zone 2 Input

TS1

142 5 6 789 103

8k2

RESISTOR 8k2

RESISTOR

Zone

1Zone

Fig 1. Activation by a

N/O Fire Signal

(select Normally Open)

Zone

1Zone

Fig 2. Activation by a

N/C Fire Signal

(Select Normally Closed)

142 567 8 9 103TS1

142 5 6 7 8 9 103

TS1

Zone

1Zone

(+24)

(-)

(+24)

(-)

Fig 4. Activation by

Applying a +24v d.c Fire Signal

(Select N/O)

1 42 5 6 7 8 9 103

TS1

Zone

1Zone

8k2

RESISTOR 8k2

RESISTOR

2.1) Mains Power - In (TS3A)

2.2) Mains Power - Out (TS3)

2.3) Battery (TS4)

TS3A

230V AC

50Hz

Mains In

TS3A

230V AC

50Hz

Mains Out

BLACK

RED

WARNING

FIRE

SHUTTER

CLOSING

TS5

TS1 TS1A

TS6

Terminal

Block Positions

and LED

Indicators

TS6

TS3

TS3A

TS4

TS6

LED

INDICATION

Fit Link

2.8) Photo Beam (optional - see programming)

Stops and re-opens a closing door for a

pre-determined number of operations

in fire condition

2.9) Relays Outputs

The unit is fitted with individual relays to provide different functions as required

All contacts are at a volt free potential (dry contact) and are rated at 230v AC

16A

Typical Reflective

photocell

(style and wiring colours may vary)

(N/C)

(COM)

(-)

(+)

Photo Beam

STOP - Relay (1 + 2)

ANormally Closed contact that will open

circuit when the Stop button is pressed

(Disabled on receipt of a Fire signal)

OPEN - Relay (3 + 4)

ANormally Open contact that will provide a

closed circuit when the Open button is

pressed

(Disabled) on receipt of a Fire signal)

CLOSE - Relay (5 + 6)

ANormally Open contact that will provide a

closed circuit when the Close button is

pressed

(Disabled) on receipt of a Fire signal)

AUX 1 - Relay (7, 8, 9)

ANormally Closed Relay that will change

state when activated

Relay is only switched upon receipt of a fire

signal

AUX 2 - Relay (10, 11, 12)

ANormally Closed Relay that will change

state when activated

Relay is programmable to simulate other

relays or switch upon Low Battery power or

Mains Fail

(N/O) (not used)

2.10) 24v d.c Solenoid Output

A brake release device or solenoid unit can

be activated when connected to the output

provided

This output can operate a brake release unit

rated at 24v d.c

To 24v d.c

Brake Release

Device

11 1412 15 16 17 18 19 20

TS1A

11 1412 15 16 17 18 19 2013

TS1A

11 1412 15 16 17 18 19 2013

TS1A

11 1412 15 16 17 18 19 2013

TS1A

OPEN

STOP

CLOSE OPEN

COM

2.5) Push Button (optional)

Connection of a typical 3 push button station to

operate the door under normal conditions

2.6) Key Switch (optional)

Connection of a typical keyswitch to

operate the door under normal condition

2.7) Panic Button (optional)

Connection of a normally open panic button to

re-open the door under an emergency to 75% of

full close time

11 = COM

12 = STOP

13 = OPEN

14 = CLOSE

11 + 12 COM (LINKED)

13 = OPEN

14 = CLOSE

17 = +24V DC

18 = 0V

19 = COM

20 = N/C

Function ( to be used on power closing)

A connected Photo Beam will stopand

re-open a closing door when in firealarm

condition only

It is programmed for a pre-set numberof

attempts to close the shutter if thebeam is

broken

On the final attempt the Photo Beam will

ignore any furtehr obstrutions and close the

shutter as far as possible

(Always active on power and 2 stage closing)

NEUTRAL (COM)

EARTH

DIRECTION (L1)

Note:

THIS CIRCUIT IS PROTECTED BY FUSE 'F3' WITH A

MAXIMUM RATING OF 6.3A

THE PANEL MUST THEN BE SET FOR 'POWER CLOSING

(SEE PROGRAMMING INSTRUCTION)

CONSIDERATION MUST BE TAKEN FOR THIS

CONFIGURATION, DOOR WILL ONLY RUN PROVIDING 230V

AC MAINS SUPPLY IS AVAILABLE

A SUITABLE BATTERY BACK UP THEREFORE MAY NEED

PROVIDING IN THE EVENT OF LOSS OF MAINS POWER

DIRECTION (L2)

230V AC

3.1 Typical Connection for 230v AC Tubular Motors

(Use with "Power Closing" or "2 Stage Closing")

(+VE)

(-VE)

Note:

THIS CIRCUIT IS PROTECTED BY FUSE 'F1' WITH A

MAXIMUM RATING OF 4A

THE PANEL MUST THEN BE SET FOR 'POWER CLOSING

WITH AUX 2 SELECTED FOR 'OPEN'

(SEE PROGRAMMING INSTRUCTION)

CONSIDERATION MUST BE TAKEN FOR THIS

CONFIGURATION, DOOR WILL ONLY RUN PROVIDING 230V

AC MAINS SUPPLY IS AVAILABLE

A SUITABLE BATTERY BACK UP THEREFORE MAY NEED

PROVIDING IN THE EVENT OF LOSS OF MAINS POWER

24V d.c

3.2 Typical Connection for 24v d.c Tubular motors

(Use with "Power Closing" or "2 Stage Closing")

JM POWER SUPPLY CONNECTION

FOR 3 PHASE OPERATORS, AN

INDEPENDENT SUPPLY (3PH, N, + E)

MUST BE INSTALLED

FOR 1 PHASE OPERATORS THE

MOTOR SUPPLY CAN BE SUPPLIED

VIA AN INDEPENDENT SUPPLY OR

TAKEN DIRECTLY FROM TERMINAL

TS3 -PE, L, N

3.3 Connection for 'JM' series motors

fitted with 24V DC brake release solenoid unit

(Use with "Power Closing" , "2 Stage Closing" and Solenoid Only")

Table des matières

Autres manuels Ellard Alarme incendie

Ellard

Ellard FDCP-03 Manuel utilisateur

Manuels Alarme incendie populaires d'autres marques

Zeta Alarm Systems

Zeta Alarm Systems INFINITY ID2 Manuel utilisateur

System Sensor

System Sensor 22051TLE-RF-26 Manuel utilisateur

Pittway

Pittway Notifier AM2020 Manuel utilisateur

Ampac

Ampac ZoneSense Manuel utilisateur

Kidde

Kidde VM-1 Manuel du produit

LST

LST SIM016-3 Manuel utilisateur

Fireboy- Xintex

Fireboy- Xintex FBD-MZ Instructions originales

bolid

bolid S2000-IP-03 Manuel utilisateur

GST

GST DI-9204 Manuel utilisateur

E2S

E2S BExTBG05D Manuel utilisateur

Notifier

Notifier UZC-256 Manuel utilisateur

Fire-Lite Alarms

Fire-Lite Alarms MS-2 Manuel utilisateur

Siemens

Siemens FDOOT221 Manuel utilisateur

hyfire

hyfire HY5000 Series Manuel utilisateur

FlameStop

FlameStop PFSIFP8 Manuel utilisateur

Radionics

Radionics Radionics 9124 Manuel utilisateur

UniPOS

UniPOS FD 7120 Manuel utilisateur

FIREWOLF

FIREWOLF FW-C01224 Manuel utilisateur